ToSee 2C-10W-1 Watchman Solar Battery Camera User Guide
- June 6, 2024
- ToSee
Table of Contents
ToSee 2C-10W-1 Watchman Solar Battery Camera User Guide
Appearance introduction
Name/ Description
Solar Panels: When the sun is strong, that can charge the device battery.
Infrared Light: When the ambient light is not enough, enable the infrared
light to increase the brightness of the environment.
Light Sensor: Used to collect ambient brightness values, when the
illumination is lower than 2Lux, enable the infrared light.
Pickup Device: Collect ambient sounds and implement voice intercom.
PIR Detection: When the human body moves in front of the device, it can
generate a trigger signal to the mobile phone. Capture image video.
Lens: Capture image videos.
Indicator Light: Red light flashes slowly: the system waits in the WiFi
configuration. The blue light is slow: the system is in normal working
condition. Red and blue flashing alternately: system WiFi connection failed
Name/ Description
Reset Key: The device in the working status, then press and hold for 5
seconds to restore the factory settings.
TF Card: Install TF card to support local recording
Battery Switch: Turn off and turn on the device battery by turning on the
key
USB Interface: Charge the device battery through the USB interface
Bracket mounting: Mounting on the wall using the accessory bracket
Speaker: Issue system prompts and implement voice intercom
Note: You need to open the bottom silicone to see the function interface as shown.
Installation Instructions
Pay attention to the installation polarity: “+” positively installed inward.
Improper installation can cause equipment damage.
Do not disassemble the battery if necessary
Operate as shown, using mounting screwslnstall the bracket and adjust the
angle to make the PIR Enough to detect people.
Installation Notes
Installation:
1. The human body induction effective distance is 3-5 meters, so please
adjust the monitoring angle according to the actual situation.
2. Please avoid the installation position where the temperature changes too much, such as heat source, airoutlet, etc. it will cause frequent alarm of equipment.
Alarm adjustment: The device default setting triggers the alarm immediately. If you need to adjust the sensitivity. please go to the device settings page.
Solar panels: Please ensure that the sun is fully exposed.
Connect Device
How to download the mobile phone App
Please search “Smart Life” in the mobile IOS “app store”, android phone on “Google Play”,
Notice: When running the app for the first time, several windows will pop up to get permission for the phone. For better using experience, it is recommended that you allow the app to obtain the following two permissions.
Allow Smart life to use mobile cellular data and wireless LAN (Function: Whether it is WIFI or using mobile phone traffic, the phone can access the camera).
Allow Smart life to get system push message permissions (Function: When the camera triggers motion detection or sound detection alarm, the phone can receive alarm push).
New users need to register by e-mail, click “Register”, follow the steps to complete the registration of the account, and log in.
A. Username must be a valid email address.
B. Password must be between 6-20 digits in length.
C. Please choose the same country in register and login
D. If you ever forget your password, click “Forgot password” to
retrieve your password via email verification.
Before adding a device, you need to note the followings:
This camera only supports 2.4GHZ WIFI network. Before adding equipment, please ensure that your router supports 2.4GHZ WIFI network, and the mobile phone is connected to 2.4GHZ WIFI network. (For details, please refer to FAQ of this manual)
If the device fails to be added, press and hold the reset button on the device to restore the device to the factory settings. After the device indicator flashes red fast and you hear the beep, try again.
A camera can only be added by one account. If the camera has been already added, it cannot be added twice. You can share the device.
Add the camera by QR Code
- When the device is powered on, the indicator light will be on. After the beep is heard, the device indicator light flashes red quickly.
- After the phone is connected to Wi-Fi, click “+” top right then select ” Video Surveillence”, then select Smart Camera.
- After confirming that the device indicator is flashing red quickly, click “Next”.
- After entering the correct WIFI and password, click Next. (Display the password to check if the password is correct)
- Press continue, then align the QR code on the screen of the mobile phone with the lens of the camera, about 15cm away (do not shake your hands during the process, ensure the screen of the mobile phone is free of cracks)
- You will hear the device beep and click “I hear the beep” (If you don’t hear the prompt, click “no prompts” for help).
- The device indicator starts flashing blue quickly, then the blue light is always on. The mobile app starts counting seconds and is searching for devices waiting for a connection. After the APP prompts that the device has been searched, click “Done”.
The device lens is aimed at the QR code on the phone screen with a distance of 15 cm. After the device recognizes the QR code, it will send out the “Beep”. Then click “I hear the beep”
Q&A
Q: The decice cannot connect to WiFi.
A:
- Please confirm that the wireless network to be connected is the 2.4G protocol.
- Makesure that the indication light is in the red light flashing slowlystate.
- Check if the account password is correct and whether there are extra spaces.
Q: What power supply methods does the device support?
A:
- The device can work alone with 18650 batteries
- Possible to charge the device through USB
Q: What storage methods does the device support?
A: The device can use the TF card for video storage, or it can use the
real-time recording and capture functions of the mobile phone for storage
Technical Specification
Visual Angle: Diagonal 104°
Infrared Light: 850mm 6pcs
WiFi: Support 802.11 b/g/n
Audio: Two-way intercom with echo cancellation
Video: TF card (15 seconds each time)
Storage: 8G/16G/32G
Battery: 2 pcs of 18650 batteries
Push: Speed Push in 2 Seconds
Wake-up Duration: Within 600ms
Wake-up Method: PIR human body induction wake-up Phone Active Wake-up
Solar Power: 1W 5V200mA
Power Consumption: Standby current 300uA Working current 250mA
It can be used for 2-3 months if working 30 minutes a day with 2 pcs of 18650 batteries (6800mAh).
Two pcs 3400mAh original 18650 batteries can be used fort-3 months
Solar charging
Full HD resolution
Support the phone wake-up device
Support the 2.4G wireless connection
Two-way Audio
Support the PIR human body infrared detection, when someone lingers in the doorway, immediately send alarm information to the smartphone APP
Day and night mode switches automatically. The clear and distinct image will help to ensure the safety of you and your family
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>