Lepro R2 Smart LED Downlight User Guide

: May 15, 2024
: Lepro

Table of Contents

App Connection
Voice Control
How to reset the light.
INSTALLATION INSTRUCTIONS
MOUNTING INSTRUCTION
FCC Warning
Customer Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Lepro R2 Smart LED Downlight

Lepro R2 Smart LED Downlight

App Connection

|
---|---
App Connection |
|

Turn on the phone’s Bluetooth and connect to the WiFi network.
App Connection

Switch the light on
App Connection

Follow the on-screen steps to finish set up.
App Connection

Voice Control

If the light does not work, please go to Amazon Alexa or Google Home APP and click DISCOVER DEVICES.
Voice Control

How to reset the light.

Switch the light off and on four times (with a 2-second interval between each).

How to reset the light.

INSTALLATION INSTRUCTIONS

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE/FIXTURE.

This luminaire is intended for installation in accordance with the National Electrical Code and local regulations. To ensure full compliance with local codes and regulations, consult with a qualified electrition before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding. Allow fixture to cool before handling.

WARNING

RISK OF FIRE OR ELECTRIC SHOCK CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.
RISK OF FIRE, Use MIN 90°C SUPPLY CONDUCTORS
DO NOT alter or make any extra holes in the wiring enclosure or electrical components during installation.
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp
objects.
SUITABLE FOR OPERATION IN AMBIENT LIGHT NOT EXCEEDING 40°C.
COVERED CEILING MOUNT ONLY.
FOR USE IN NON-FIRE-RATED INSTALLATIONS ONLY.
ACCESS ABOVE CEILING REQUIRED.
TYPE IC, INHERENTLY PROTECTED.

CAUTION

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
Edges may be sharp. Please wear gloves while handing.
Product is designed for dimming with many 120V TRIAC phase cut control dimmers.
Product can be installed directly into a ceiling without requiring separate J-box or recessed housing.
Connect fixture to a 120V 60Hz power source. Any other connection type voids the warranty.

MOUNTING INSTRUCTION

Installation (for new construction & remodeling)

Mounting Instruction

PRE-MOUNTING FOR NEW CONSTRUCTION

Install drywall directly over rough-in plate. NOTE: Locate the center of the aperture hole.
Cut an opening in the ceiling (use a hand saw, hole saw, etc.) using the provided template (fig. 1). CAUTION: Do not cut hole larger than the plate opening.

MOUNTING

Make sure the POWER IS TURNED OFF (at the source) to the location in which you are mounting the luminaire.
Open the cover of the provided J-BOX and use three “Quick connect” push-in terminals to make connections with power supply. Place splices in J-BOX before closing cover (fig. 2).
Connect the J-BOX to light module (fig. 3).
Place the J-BOX through the cut-out hole and mount according to local electrical code.
Rotate and hold both spring clips upward to allow passage through the hole in the ceiling. Continue to press the light module through the hole until it is securely fixed and flush with the ceiling (fig. 4).

REMOVAL

Turn off power to the luminaire.
Simply pull down firmly on the light module until the spring clips release from the ceiling. Reach through the ceiling to hold the clips up and away from the ceiling as you continue to pull the light module from the ceiling opening.
CAUTION: DO NOT PLACE HANDS UNDER SPRING CLIPS DURING REMOVAL OF THE LIGHT MODULE.
Disconnect wiring.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in ac chordwise with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will out occur in a particular installation. If this equipment does cause handful interference to radio or television reception, which caw, be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment wad receiver.
connect the equipment into an outhit an a circuit different from that to which the receiver is connected.
consult the dealer or w, experienced radio/TV technician for help.

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limit set forth for an uncontrolled environment. This transmitter must not be ca – located or operating in conjunction with any other wireman or transmitter.
This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.

ISEDC Warning This device complies with Innovation, Science and Economic Development Canada licence-exempt ASS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

ISEDC Radiation Exposure Statement:

This equipment complies with ISEDC RF radiation exposure limits set forth for an uncontrolled environment This transmitter must not be co-located or operating in conjunction with other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.