TUNAI Z10W06 Qi Wireless Car Charger User Guide

USER GUIDE
Ｍagnetic suction automatic positioning
wireless charging mobile phone holder
This product is compatible with iPhone 12/ 13 series
Please read this operation
Instruction carefully and keep it properly before using this product

Product introduction

Thank you for purchasing and using this product! In order to ensure that you can provide a better operating experience for your mobile phone or electronic products.

5V 2A | 9V 1.67A | 12V 2A

| Output power| 5V 5W | 9V 7.5W
12V 10W| 12V 15W
Frequency| 110-205KHZ| Efficiency| 80%-83%
Product name| Qi Car Charger| Model name| Z1OW06
Operating

temperature

| 0°C∼45°C| Importer| Sagittech Technology
Address| 3rd Floor, No. 30, Section 1, Chongqing North Road, Datong District Taipei City

PS： The above information is based on real sample testing, it will be a little bit different for various products in different conditions.

Operation

1. Please wipe the car dashboard carefully with the damp cloth
   

2. Tear off the protection film of the tape
   

3. Paste the bracket on the dashboard
   

4. Plugin the charging cable, shake the phone to align the magnet then complete the installation
   

5. Another bracket base can be replaced
   

6. Loose the nut and open the air outlet chuck
   

7.  Install the bracket to the vent, tighten the bracket by rotating the nut, and then connect the car charger and mini USB cable that meets QC3.0 standard for power supply

NCC Warning：
For low-power radio frequency equipment that has been certified, companies, firms, or users are not allowed to change the frequency, increase the power, or change the characteristics and functions of the original design without approval. The use of low-power radio frequency equipment must not affect flight safety and interfere with legal communications; if interference is found, it should be stopped immediately and improved to no interference before continuing to use. Legal communications in the preceding paragraph refer to radio communications that operate in accordance with the provisions of the Telecommunications Administration Law. Low-power radio frequency equipment must endure the interference of legal communications or industrial, scientific, and medical radio wave radiation electrical equipment.

Note!

1. Please align the phone magnet with the wireless charging magnet to avoid the magnetic attraction does not work.
2. Please make sure you are using Magsafe cases. It can’t compatible with non-MagSafe cases. Non-MagSafe cases will make magnetic force is weak and can’t charge.
3. No metal plate on the back of the phone, because it will stop phone charging.
4. Don’t use the wireless charger in high temperatures, humidity, or corrosive environment, avoid damaging the circuit and avoid leakage.
5. Take care of children to ensure they will not play with wireless chargers as a toy, in order to avoid unnecessary accidents.
6. To ensure fast and safe charging, we select the QC2.0/QC3.0 standard car charger and the best four-core universal data cable, other nonstandard car chargers or cables will make the charging slow.
7. If the car temperature inside is too high, the charging will become slow; with the cold wind from the air outlet, charging on the air outlet will be much better, with the hot wind from the air outlet, please charge the mount on the dashboard.

Equipment name  Type designation (Type)  Z10W06

Unit| Restricted substances and their chemical symbols
(Pb)| (Hg)|

(Cd)

|

Hexavalent
chromium
(Cr+6)

|

Polybrominated
biphenyls
(PBB)

| Polybrominated
diphenyl ethers
(PBDE)
Circuit board| 0| 0| 0| 0| 0| 0
Metal board| 0| 0| 0| 0| 0| 0
Silicone| 0| 0| 0| 0| 0| 0
Metal glue| 0| 0| 0| 0| 0| 0
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of a present condition.
Note 1: “O” indicates that the percentage content of the restricted substance does not exceed the percentage of the reference value of presence.
Note 3: “The “—”. indicates that the restricated substance corresponds to the expeditions.

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment.
During the operation of device, a distance of 15cm surrounding the device and 20cm above the top surface of the device must be respected

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>