EMAX E8 Transmitter Instructions
- June 6, 2024
- Emax
Table of Contents
EMAX E8 Transmitter
E8 Transmitter is a new wireless controller released by EMAX. It has a built-
in 2.4GHz dual-band antenna and a 2.4GHz RF module. The RF module supports 8
channels. The channel ange is configurable and compatible with most receivers
on the market. It is equipped with a wired trainer interface and simulation.
The Mode of the device can switch between left and right-hand modes, and the
ergonomic design can bring a good user experience paired together with a
built-in battery that can be charged via USB.
1. structure diagram
Specifications
Product model: EMAX E8 Transmitter
Weight: 260g (without battery)
Size: LWH=150x140x45mm
Working voltage : 3.7V-4.2V
Channel: 8 channels, all channels can be configured
External interface : Micro USB interface, 3.5mm audio interface (wired
trainer interface)
Transmitting module: built-in 2.4GHz dual-frequency FPC antenna, 2.4GHz
RF transmitting module
Working frequency band: 2.4GHz (2400MHz-2483.5MHz) Maximum output power:
22dbm
Charging system: Built-in USB 5V–1A linear lithium-ion battery charging
system
Use operation
1. Toggle switch operation instructions (factory default)
Toggle switch AUX1 : 3 sections: unlocking
Toggle switch AUX2: 3 sections: flight mode
Toggle switch AUX3: 2 stages: buzzer
Toggle switch AUX4: 2 stages: anti-turtle mode
Description of Turtle mode (as an example in the left-hand mode):
Sometimes the drone falls to the ground while flying. Turtle mode can be used
to reverse the drone upright. First Disarm switch AUX1, turn the Turtle Mode
AUX4 switch up, then Rearm, then shake the pitch and roll sticks to turn the
aircraft over.
Key operation instructions
Trim Buttons
When in left-hand mode (left-hand throttle):
1. L1+, L2- are the parameters “+, -” of the throttle [T] 2. L3-, L4+ are
the parameters “-, +” of the direction [R] 3. R1+, R2- are the parameters “+,
-” of the pitch [E] 4. R3 -, R4+ are the parameters “-, +” of the roll [A]
Mode switching
D8 mode : press the power switch and the “L1+” button at the same time:
turn on and enter D8 mode, then the mode indicator will turn solid red.
D16 mode : press the power switch and the “L2-” button at the same time:
turn on and enter D16 mode, then the mode indicator light will turn solid
green.
D16 LBT mode: Press the power switch and the “L4+” button at the same
time: Turn on the controller and enter D16 LBT mode, then the mode indicator
light will turn solid yellow.
3. Charging system and battery installation instructions
Power charging indicator status:
When Red LED is solid: charging is in progress.
When Green LED is solid: charging is finished.
Note: Use a 5V-1A adapter to charge. When the voltage is low, it will
alarm. Please recharge when low.
Battery & Charging
The E8 Transmitter is compatible with a 18650 battery, with a working voltage
of 4.3V-3.3V. When you need to reinstall the battery, remove the battery
compartment cover and install the battery according to the correct polarity
(the negative pole is on the spring side of the battery compartment). Confirm
that the battery compartment cover and the battery compartment are perfectly
matched then push forward until locked. If the battery is not installed
correctly, charging and starting cannot be performed correctly.
The remote control is charged with the micro USB at the bottom. After the USB
cable is inserted, the power charging indicator status:
When the indicator light is solid red: charging Solid green indicator
light: charging is full
Note: Use a 5V-1A adapter for charging and a micro USB cable for charging.
When the voltage is low (3.3V), it will alarm. Please charge when the battery
is low.
Note: It can be turned on and charged only when the battery polarity is
correct, it will not turn on or charge.
Instructor port and simulator operation
Trainer Port for Simulators
Insert one end of 3.5mm male to male into the trainer port (3.5mm audio
interface), and plug the other end into the simulator (sold separately) to
output the corresponding channel value. Plug the micro USB cable into the
remote control to output the corresponding channel value.
5. Gimbal Trim
Each joystick has a corresponding Trim button. Each Trim button adjusts the
direction of the corresponding joystick control. Each time it is adjusted, a
beep will sound. When it is adjusted to the center position, it will make a
longer beep. Please pay attention to the sound. With joysticks centered, use
the Trim buttons until the drone is steadily hovering in place.
Calibration of joystick
The E8 Transmitter is pre-calibrated, but recalibration can help solve some
common issues:
1. With the E8 Transmitter turned off, press the “L3-” button and the power
button at the same time as the controller turns on.
2. Wait for the center indicator to light up and change from fast flashing to
slow flashing, and push the joysticks of the E8 Transmitter to the maximum
travel in the four directions up, down, left, and right.
3. Press the “L3-” button, the prompt will sound, exit the calibration mode
** and the E8 Transmitter will then boot up.
Regarding the Mode change and switching between left and right-hand operation
instructions
7. Changing Modes:
Left-handed mode: the left-hand joystick, up and down for throttle
adjustment, left and right for direction adjustment; the right joystick, up
and down for pitch adjustment, and left and right for roll adjustment.
Right-handed model: the left joystick, up and down for pitch adjustment,
left and right for roll adjustment; the right joystick, up and down for
throttle adjustment, and left and right for direction adjustment.
Schematic diagram of the left and right-handed joysticks (the picture shows
the lefthanded mode, and of the joystick control reversed in the right-handed
mode ) Switch left and right hands**
Remove the screw and open the back cover of the E8 Transmitter housing. There
is a toggle switch on the left side of the board. Set the toggle switch to “L”
(left-hand throttle mode) or “R” (right-hand throttle mode), and swap the
positions of the levers (the 6Pin cable connecting the joystick to the
mainboard does not need to change positions).
Left-handed mode: E8 Transmitter left stick, controls the throttle and yaw
direction of Tinyhawk III; E8 Transmitter right stick, controls Tinyhawk III’s
pitch and roll. Right-handed model: E8 Transmitter left stick controls the
pitch and roll of Tinyhawk III; E8 Transmitter right stick controls the
throttle and yaw direction of Tinyhawk III.
4. support
EMAX will continue to add and improve functions, users can check through the
EMAX official website, and look forward to your good experience using this
product. More information about EMAX can be found on the following official
website:
WWW.emax-usa.com
WWW.emaxmodel.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>