Fuzhou Emax Electronic 2241BT Food Thermometer User Manual
- June 6, 2024
- Fuzhou Emax Electronic
Table of Contents
BEGAN TO USE:
OVERVIEW
DISPLAY UNIT-FRONT VIEW
- Cook temperature
- Alert temperature
- Bluetooth indicator
- °C/°F: temperature measurement unit
- Alerts
- Pairing indicator
a. – : Enter mode set-up; confirm setting; press and hold for 3sec to power off
b. + : Decrease the value of the setting; °C/°F temperature measurement unit
c. Increase the value of the setting
d. Metal Probe Connector Wire
e. Silicone sleeve
f. Metal probe
DISPLAY UNIT-REAR VIEW
-
Magnet
-
Reset button
-
Pay feet
-
Battery compartment
-
Install your battery
-
Carefully plug the meat probe into the bottom socket
-
Download APP (Smart Thermo)
3.1 Connect the APP Store to search Smart Thermo with the following device
iPhone (4S and later)
iPad (3rd generation and later)
iPad mini (all generations)
3.2 Download Android APP application software URL https://play.google.com/store/apps/details?id=com.bbq.project
Support Android 4.3 and later -
Pairing your smart thermo
4.1open the APP software, click the icon to open the APP ( ) – > Enter Bluetooth interface
click on the search -> waiting for data reception.
4.2, button operationkey
- press [SET] key to wake up.
- press 3sec the [SET] key to enter the sleep state.
- short press [SET] key, enter alarm temperature setting state.
- short press [SET] key to exit setup.
<+> key - short press [+] button, the alarm parameters accumulated.
- long press [+] button, alarm quickly accumulate parameters.
< – > key - short press [-] keys, alarm parameters decrease.
- long press button, the alarm parameters rapid decline.
- short press key [-],switching temperature units( ºC/°F ).
4.3 LED backlight - LED display 3 colors are green, blue, red.
green:Cook temperature<(Alert temperature -10 ºC)
blue:(Alert temperature -10 ºC)≤Cook temperature<Alert temperature
red:Alert temperature≤Cook temperature - When no operation, the LED will turn off after about 10 seconds.
4.4, low voltage alarm - when the battery power is low, screen displays “LO”.
- send low power information to the APP, APP prompts to replace the battery and alarm.
*SMART THERMO shows “LO” about 3sec and then automatically goes to sleep.
4.5 temperature measurement range - device measuring temperature from-25°C to 300ºC (-13°F to 572°F)
- Display “LLL” when the temperature is below the minimum temperature or when the probe plug is not inserted.
- when the temperature is higher than the maximum temperature, displays “HHH” .
5. APP function
5.1 automatic or manual searches for Bluetooth devices - open APP to enter the match screen beneath the display [search] or [lift] button
- click [search] APP automatically find the surrounding Bluetooth devices, automatically
connect and enter the temperature display interface - when Bluetooth connection failed the main interface [pairing] flashes
- after unbound the device, the user can connect to the new equipment.
5.2 APP main interface - display device temperature
- set temperature (file mode and temperature mode)
- set countdown setting time (countdown mode)
- menu setting key
- pairing key
- task start (stop) key
5.3 select the measurement unit - tap to view the Profile options of food
- tap on your food type
- tap to select cooking degree and temperature can be adjusted up and down 2 degrees
- Tap to go back to the previous screen to save.
5.4 file selection function - click the settings button to enter the settings menu.
- click on file options
- click to add food or delete the food that has been set
- alarm temperature settings.
5.5 timer settings - tap to view the Profile options of timer
*slide down and up to set time you need. Timer measurement range: 23H 59M 59S - tap to go back to the previous screen to save.5.6 alarm bell setting.
5.6 select alarm - tap to view the Profile options of rings
- tap to choose your favorite ring
- tap to go back to the previous screen to save
*if food is cooked, the alarm ring will ring and show the notification menu.
The temperature will show on the device screen and the LED backlight will flash 5 times.
5.7 sharing - Tap to view the Profile options of the camera
- Tap on the camera button.
- Tap on the share button and food cooking photos you took will be shared in your community
Warning
Meat Probe acceptable temperature range: -13°F to 572°F (-25ºC to 300ºC)
The Meat Probe should always be inserted into the center of the item which is
being cooked for an accurate temperature.
The Stainless-steel probe and wires will get hot. Always wear heat-resistant
gloves when handling.
Do not use a probe in a microwave oven or be exposed to flames or temperatures
exceeding 572°F (300°C).
Keep the probe and wires away from children.
Not intended for children under 12 years old.
Care
Clean the probe after each use.
Wash the stainless-steel probe with hot soapy water and dry thoroughly.
Do not immerse the probe in the water while cleaning.
Do not expose the probe plug to water or other liquids. This will result in
bad connections and faulty readings.
Wipe the thermometer base with a damp cloth. Do not use immerse in water.
To avoid damage, do not use cleaning agents or abrasive cleaners.
SPECIFICATION
T YPE
|
DESCRIPTION
---|---
DISPLAY UNIT
LxW| 52×45 mm
Temperature measuring range| -25°C to 300°C (-13°F to 572°F)
Temperature unit| °C/°F
Power| 2xAAA batteries
PROBE WRAP
LxWxH| 84×58.5x 28mm
METAL PROBE
Lerici| 122mm
Heat resistance for metal probe| Around 300°C(572°F)
Temperature range| -25°C to 300°C (-13°F to 572°F)
Battery life| 1 Year
Bluetooth Range| 25 meters(open territory)
Warning Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This device generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause harmful interference to
radio or television reception, which can be determined by turning the device
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the device and receiver.
–Connect the device into an outlet on a circuit different from that to which
the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment