EMAX EATIWH1S1P 1 Inch Air Impact Wrench Instruction Manual
- June 6, 2024
- Emax
Table of Contents
OPERATOR’S MANUAL
FOR 1 in. AIR IMPACT WRENCH 3,500 RPM
Model No. EATIWH1S1P
Operator Instructions
Includes Please Read and Comply, Warnings, Product Configuration and
Specifications Table, Parts Page, Parts List, Work Stations, Putting the Tool
Into Service, Compressor Layout and Safety Information.
Important
Read these instructions carefully before installing, operating, servicing or
repairing this tool. Keep these instructions in a safe accessible location.
Required Personal Safety Equipment
| | |
---|---|---|---
Safety Glasses| Safety Gloves| Breathing Masks| Ear Protection
Recommended Airline
Size – Minimum
10 mm 3/8 in| Recommended Maximum
Hose Length
8 meters 25 feet| Air Pressure
Maximum Working Pressure 6.2 bar 90 psig
Recommended Minimum NA NA
---|---|---
Please Read and Comply with
- General Industry Safety & Health Regulations, Part 1910, OSHA 2206, available from: Superintendent of Documents; Government Printing Office; Washington DC 20402
- Safety Code for Portable Air Tools, ANSI B186.1 available from: American National Standards Institute, Inc.; 1430 Broadway; New York, New York 10018
- State and Local Regulations.
****Warning
Always wear eye protection when operating or performing maintenance on this tool. Always turn off the air supply and disconnect the air supply hose before installing, removing or adjusting any accessory on this tool, or before performing any maintenance on this tool. Improper operation or maintenance of this product could result in serious injury and property damage. Read and understand all warnings and operation instructions before using this equipment.
Parts Page
Item No| Part No.| Description| Qty.| Item No|
Part No.| Description| Qty.
---|---|---|---|---|---|---|---
1| 516W02| AIR INLET| 1| 27| 517EW27| PLATE THRUST| 1
2| SO070| O-RING| 1| 28| 517AW28| HAMMER CAGE| 1
3| 517AW03| SPRING| 1| 29| 517AW29| DRIVE CAM| 1
4| AA06-15| STEEL BALL| 1| 30| 517AW30| HAMMER PIN| 1
5| 517AW05| VALVE STEM| 1| 31| 517AW31| HAMMER DOG| 1
6| 516W01| SCREEN| 1| 32| 517AW32| ANVIL| 1
7| 517AW07| RUBBER BUSHING| 1| 33| SO052| O-RING| 1
8| SP012| PIN-SPRING| 1| 34| 516W44| RETAINING RING| 1
9| 517AW09| LEVER-REVERSE VALVE| 1| 35| 516W39| BUSHING| 1
10| SP018| PIN SPRING| 1| 36| 517AW36| HOUSING COVER| 1
11| 517AW11| TRIGGER| 1| 37| 516W55| OIL SEAL| 1
12| SH012-1| SCREW & SPRING WASHER| 8| 38| 516W04| COVER| 4
13| 517AW13| THROTTLE HANDLE| 1| 39| SH009-1| SCREW & SPRING WASHER| 1
14| 517AW14| GASKET| 1| 40| SH043| SCREW| 1
15| CA6204Z| BEARING BALL| 1| 41| 516W62-31| HANDLE DEAD| 1
16| 517AW16| REAR PLATE| 1| 42| AA06-8| STEEL BALL| 1
17| 517EW17| PIN| 1| 43| 517AW43| SPRING| 1
18| 517AW55| RETAINER| 1| 44| 517AW44| VALVE REVERSE| 1
19| 517AW19| CYLINDER| 1| 45| 517AW45| SPRING-THROTTLE VALVE| 2
20| 517AW20| ROTOR| 1| 46| SP013| PIN-SPRING| 1
21| 517AW21| ROTOR BLADE| 5| 47| 2201D09-1| SCREW| 1
22| 517AW22| FRONT PLATE| 1| 48| SO017| O-RING| 1
23| CA6005ZZ| BEARING BALL| 1| 49| 510W38| RUBBER| 1
24| 517AW24| HOUSING| 1| 50| 516W15| OIL SEAL| 1
26| 517AW26| GASKET| 1| 51| 517AW52| SPACER| 1
| | | | 52| SO070| O-RING| 1
Product Configuration/Specifications
Model Number| Free Speed
(rpm)| Square Drive
in. (mm)| Maximum
Torque
ft-lb| Product Net
Weight
Pound (kg)| Height
in. (mm)| Length
in. (mm)| Air
Consumption
dm (LPM)
---|---|---|---|---|---|---|---
EATIWH1S1P| 3,500| 1 (25.4)| 1,400| 26.0 (11.82)| 6.57 (167)| 22.8 (580)| 14
(396)
Specifications subject to change without prior notice.
The actual exposure values and amount of risk or harm experienced to an
individual is unique to each situation and depends upon the surrounding
environment, the way in which the individual works, the particular material
being worked, work station design as well as upon the exposure time and the
physical condition of the user. EMAXTM cannot be held responsible for the
consequences of using declared values instead of actual exposure values for
any individual risk assessment. Further occupational health and safety
information can be obtained from the following
websites:https://osha.europa.eu/en (Europe); http://www.osha.gov (USA)
Work Stations
The tool is intended to be operated as a hand held tool. It is always recommended that the tool be used when standing on a solid floor. It can be in any position but before any such use, the operator must be in a secure position having a firm grip and footing and be aware that the tool can develop a torque reaction. See the section “Safety Information”.
Putting the Tool into Service
Use a clean lubricated air supply that will give a measured air pressure at
the tool of 90 psig (6.2 bar) when the tool is running with the lever fully
depressed. It is recommended to use an approved 3/8 in. (10 mm) x 25 ft (8 m)
maximum length airline. It is recommended that the tool be connected to the
air supply as shown in Figure 1.
Do not connect the tool to the airline system without incorporating an easy to
reach and operate air shut off valve. The air supply should be lubricated. It
is strongly recommended that an air filter, regulator and lubricator (FRL) be
used as shown in Figure 1 as this will supply clean, lubricated air at the
correct pressure to the tool. Details of such equipment can be obtained from
your supplier. If such equipment is not used then the tool should be manually
lubricated
To manually lubricate the tool, disconnect the airline and put 2 to 3 drops of
suitable pneumatic Airbase synthetic air tool oil must be used for lifetime
warranty. Part# OIL012 into the hose end (inlet) of the machine. Reconnect
tool to the air supply and run tool slowly for a few seconds to allow air to
circulate the oil. If the tool is used frequently, lubricate it on a daily
basis or lubricate it if the tool starts to slow or lose power. It is
recommended that the air pressure at the tool be 90 PSI (6.2 Bar) while the
tool is running so the maximum RPM is not exceeded. The tool can be ran at
lower pressures but should never be ran higher than 90 PSI (6.2 Bar). If ran
at lower pressure the performance of the tool is reduced.
Safety Information
- Read all instructions before using this tool. All operators must be fully trained in its use and aware of these safety requirements. All service and repair must be carried out by trained personnel.
- Never direct air at yourself or anyone else.
- Install air fitting into inlet bushing of tool.
- Always remove the air supply to the tool before fitting, adjusting or removing the abrasive/accessory.
- Always wear required safety equipment when using this tool.
- When operating always place the tool on the work then start the tool. Always remove the tool from the work before stopping. This will prevent gouging of the work due to excess speed of the abrasive/accessory.
- Always adopt a firm footing and/or position and be aware of torque reaction developed by the tool.
- Use only correct spare parts.
- Always ensure that the workpiece is firmly fixed to prevent its movement.
- Check hose and fittings regularly for wear. Do not carry the tool by its hose; always be careful to prevent the tool from being started when carrying the tool with the air supply connected.
- Dust can be highly combustible. Keep working area clean.
- Dust from some work processes can cause cancer, birth defects or other respiratory diseases. Risk assessment of these hazards and implementation of appropriate controls is essential.
- Direct the exhaust so as to minimized disturbance of dust in a dust filled environment
- Do not operate the tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. The abrasives are able to create sparks when working material, resulting in the ignition of the flammable dust or fumes.
- Do not exceed maximum recommended air pressure. Use safety equipment as recommended.
- The tool is not electrically insulated. Do not use where there is a possibility of coming into contact with live electricity, gas pipes, water pipes, etc. Check the area of operation before operation.
- Take care to avoid entanglement with the moving parts of the tool with clothing, ties, hair, cleaning rags, etc. If entangled, it will cause the body to be pulled towards the work and moving parts of the machine and can be very dangerous.
- Keep hands away from rotating or accessories, spindles or other moving parts during use.
- If the tool appears to malfunction, remove from use immediately and arrange for service and repair.
- Do not allow the tool to free speed without taking precautions to protect any persons or objects from the loss of the abrasive/accessory.
- Do not allow tool to free run for an extended period of time as this will shorten its life.
Year Standard Warranty
Our Standard warranty covers defects or failures in workmanship or materials
in our air tools 2 years from the date of purchase. EMAX will repair or
replace; at their discretion any defective part or unit which proves to be
defective. This warranty does not cover incidental/consequential damages and
failures due to misuse, abuse or normal wear and tear. Any modification,
repair or repair attempts not authorized are not covered under this warranty.
Shipping for warranty claims are included in this warranty for the first 90
days.
*Limited Extended Lifetime Warranty
Our LIMITED EXTENDED LIFETIME WARRANTY is our no questions asked warranty. It
covers defects or failures in workmanship or materials in our air tools for
the life of the tool. EMAX will repair or replace; at their discretion any
defective part or unit which proves to be defective. This warranty does not
cover incidental/consequential damages and failures due to misuse, abuse or
normal wear and tear (sanding pads and discs, chisels, tips, needs, nozzles,
etc).
ANY MODIFICATION, REPAIR OR REPAIR ATTEMPTS NOT AUTHORIZED ARE NOT COVERED
UNDER THIS WARRANTY. SHIPPING FOR WARRANTY CLAIMS ARE INCLUDED IN THIS
WARRANTY FOR THE FIRST 90 DAYS.
3 SIMPLE STEPS TO QUALIFY FOR YOUR EXTENDED LIFETIME AIR TOOL WARRANTY :
- Register your air tool purchase at www.emaxwarranty.com , be sure to have your original receipt of purchase in hand for important information needed in your registry.
- Write a review on the site where you purchased your air tool
- Send us a screen shot or photograph of your review to NGRUBE@EMAXCOMPRESSOR.COM to complete your extended lifetime warrantyregistration.
For warranty claims or more information call EMAX directly at: 1-866-294-4153
EMAX PHONE: 1-866-294-4153
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>