SuperFish E4020250 10W Aqua LED Spot Instructions
- June 6, 2024
- SuperFish
Table of Contents
SuperFish E4020250 10W Aqua LED Spot
Read this manual carefully before using this device. Keep this manual for future reference.
Symbols
The following warning symbols and/or signal words are used in this manual:
DANGER!
This means an imminent danger due to electric current. Failure to follow the
safety instructions can result in serious or fatal injury and/or serious
damage to the product or environment.
WARNING!
This means a dangerous situation. Failure to follow the safety instructions
can result in moderate or minor personal injury and/or damage to the product
or environment.
NOTICE!
This means caution, useful information or advice.
Meaning of the symbols on the device itself:
This device may only be used inside the house for aquarium purposes.
This device has protection class III.
This device is waterproof.
This device complies with all applicable EU standards.
This device may not be disposed of with normal household waste but must be
collected separately for recycling.
Use
Only suitable for indoor use for aquarium purposes.
Safety
Always follow the safety instructions below for safe use of the device. Failure to follow these instructions may endanger persons or the environment.
- This device must be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30 mA.
- Ensure the voltage shown on the label matches the mains supply voltage.
- Protect the socket and plug against moisture. Use a drip loop to ensure that water cannot reach the socket, adapter, switch and cable connector via the power cord.
- Don’t use the product if the device, cord or adapter is damaged. Return the device to your dealer for repair or recycling. The adapter can be replaced.
- Be careful with the combination of water and electricity. Do not operate with wet hands. Dry hands before carrying out maintenance.
- Always switch off all devices in the aquarium before maintenance. Disconnect the plug(s) from the socket.
- Do not immerse the LED lighting in water. Although the lighting is waterproof, there must be at least 15 mm distance between the lighting and the water surface.
- Install the LED lighting correctly above the aquarium. Only then plug in the mains plug.
- If the lighting falls into the water, first pull the plug out of the socket. Then lift the lighting on the cord out of the water.
- NOTICE! The LED lighting becomes warm. Allow the lighting to cool down before carrying out maintenance.
- This device can be used by children aged from 8 years and above, persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, if they have been given supervision or instructions concerning the use of the device in a safe way and understand the hazards involved. Children shall not play with the device. Cleaning and maintenance of the device shall not be done by children without supervision.
- Modifications to the device may affect the safety. The warranty will also expire.
Function
The Aqua LED Spot is a spotlighting for open aquariums. Suitable for tropical and coldwater aquariums with a glass thickness up to 10 mm.
Installation
Fig. Attach the lamp clamp to the aquarium glass and tighten it securely. Connect the cable of the lamp to the adapter and put the plug in the socket.
Maintenance
- Clean the lighting regularly with a damp cloth. This extends the longevity and improves the light output. The LEDs cannot be replaced. Replace the lighting if the LEDs no longer work.
- For maintenance of the aquarium you can tilt the LED lighting up.
Recycling
This symbol indicates that this product (if it is discarded) may not be
disposed of with normal household waste. Instead it must be handed in at an
official collection centre (e.g. HWRC). Or can be returned to the dealer when
purchasing a similar new product. Follow the applicable rules in your country
for the separate collection of electrical and electronic products.
Separate collection and recycling are better for the environment, public
health and reduces waste.
Warranty
2 years manufacturer’s warranty on materials and construction defects. Devices
must be returned complete with all components, accompanied with an official
proof of purchase confirming a purchase date for any warranty claims.
Incomplete devices of which parts are missing, and devices without proof of
purchase are not eligible for warranty. After receiving and checking, we will
determine whether the device will be repaired or replaced. For a device
repaired or replaced under warranty, the remaining time of the original
warranty period applies.
Carefully read the instructions on installation, use and maintenance. Damage
due to incorrect use, damage due to immersion in water, damage due to
contamination or not cleaning the device and damage to the cord are not
covered by the warranty. Always keep the proof of purchase, without proof of
purchase the warranty will be void!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>