SAFE FLEET Focus X2 Body Worn Camera User Manual
- June 6, 2024
- SAFE FLEET
Table of Contents
FCC part 15B
Guidelines for Labelling and User Information for Devices Subject to Part 15 ( from FCC 784748 D01 Labelling Part 15 &18 Guidelines v07)
Labelling Requirements for Part 15 Devices:
Verification
The specific labelling requirements for a device subject to the Verification
procedure are contained in Section 15.19(a). These labelling requirements are:
If the device is subject only to Verification, include a label bearing a
unique identifier (Section 2.954) and one of three compliance statements
specified in Section 15.19(a). If the labelling area for the device is so
small, and/or it is not practical to place the compliance statement on the
device, then the statement can be placed in the user manual or product
packaging (Section 15.19(a)(5)). However, the device must still be labelled
with the unique identifier (Verification).
Generally, devices smaller than the palm of the hand are considered too small
for the compliance statement.
Certification
If the device is subject to Certification: (1) Section 2.925 contains
information on identification of the equipment; (2) include a label bearing an
FCC Identifier (FCC ID) (Section 2.926) and (3) include the appropriate
compliance statement in Section 15.19(a). If the device is considered too
small and therefore it is impractical (smaller than the palm of the hand) to
display the compliance statement, then the statement may be placed in the user
manual or product packaging. However, the device must still be labelled with
the FCC ID. If the device is unquestionably too small for the FCC ID to be
readable (smaller than 4-6 points), the FCC ID may be placed in the user
manual. However, it must be determined that the device itself is too small –
the label area allocated to the FCC ID may not be reduced because of the
overcrowded identification of other products and regulatory information.
An electronic display of the FCC ID (see 9. Electronic Labelling below) may be
used for Certification of Section 15.212 modular transmitters and software-
defined radios (Section 2.944).
Declaration of Conformity (DoC)
The labelling requirements for a device subject to the DoC procedure are
specified in Section 15.19(b). The label should include the FCC logo along
with the Trade Name and Model Number, which satisfies the unique identifier
requirement of Section 2.1074 if it represents the identical equipment tested
for DoC compliance. For personal computers assembled from authorized
components, the following additional text must also be included: “Assembled
from tested components,” “Complete system not tested.” When the device is so
small and/or when it is not practical to place the required additional text on
the device, the text may be placed in the user manual or pamphlet supplied to
the user. However, the FCC logo, Trade Name, and Model Number must still be
displayed on the device (Section 15.19(b)(3)).
Equipment certified as software-defined radio may use a means that readily
displays the FCC ID on an electronic display screen, instead of labelling the
device (Section 2.925 (e)).
-
Focus X2 body-worn camera.
Single Office Dock
-
Accessory:
Focus X2 body-worn camera x 1pcs
Single Office Dock x 1pcs
USB cable x 1pcs
V/2.5A AC-DC Power Adapter x 1pcs -
LCD Display
Display the status of Operation/Bluetooth/Battery/WIFI/Storage capacity -
Buttons.****
Button| Power button| Power on/off
---|---|---
SYNC button| WIFI on/off
Recording button| Start/Stop video recording
Fn function button| Users can set different functions via config.ini setting Tag/Bookmark/Snapshot
Mute button| Mute/Un-mute
LCD display backlight button| Press it to turn on the backlight for 5seconds and then turn off the backlight automatically
Force reset button| If BWC crashes, press this button to force reset the BWC. -
RF function.
A. Hold Power button 2secs to turn on BWC
B. NFC tag is in the front of BWC. Use additional NFC writer/reader device to write Bluetooth MAC address to NFC tag.
C. User can link BWC via Bluetooth of computer / mobile phone and remote control BWC to start/stop video recording. When Bluetooth is connected, the STN LCD will display a Bluetooth icon.
D. Hold Sync button 2secs to turn on the WIFI function, the STN LCD will display the WIFI icon. Users can connect BWC via WIFI of computer/mobile phone for files download or video streaming.
FCC STATEMENT:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
RF warning statement:
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
This device complies with Industry Canada licence-exempt RSS standard( s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.”
The device has been tested and is in compliance with SAR limits. This
equipment should be installed and operated with a minimum distance of 10mm
between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>