LEXIN-B4FM-EN Motorcycle Bluetooth Headset Instruction Manual

June 4, 2024
LEXIN

Table of Contents

LEXIN-B4FM-EN Motorcycle Bluetooth Headset

Watch Instruction Video Online
Subscribe to our Youtube channel lexinmoto and find B4FM with X icon button Instruction videos. For the most updated instruction video, please click on the link that shows the X icon button and USB-C connector.

Function Introduction

  • Bluetooth 5.0
  • Hands free calling
  • Built-in CVC/DSP noise reduction
  • USB-C quick charge equipped
  • Support voice prompts, power voice announcement
  • Support Siri and other voice assistants
  • Support universal pairing with most Bluetooth Intercom
  • Support 1-10 B4FM devices connection, the longest intercom distance is 2Km/l.2miles.
  • Connect to GPS Navigation
  • Plays music and FM Radio
  • Support Music Sharing
The B4FM is compliant with Bluetooth Specification

VS.O supporting the following profiles

  • Headset Profile (HSP)
  •  Hands-Free Profile (HFP) and Advanced Audio Distribution Profile (A2DP).

It supports universal pairing with almost all Bluetooth headsets on the market.

Battery

The B4FM features an 800 mAh battery which can provide the intercom device with 15 hours of music or 15 hours of intercom talk with over one week of standby time.

Function Priority

The B4FM operates in the following order of priority)

  1. Mobile phone
  2.  lntercom Talk
  3. Music/FM Radio/GPS

Note
A lower-priority function is always interrupted by a higher-priority function. For example, stereo music can be interrupted by an intercom call, intercom talk can be interrupted by an incoming phone call.

WARNING
PLEASE CHECK ALL LOCAL LAWS AND REGULATIONS REGARDING THE USE OF IN-HELMET SPEAKERS WHILE OPERATING MOTORIZED VEHICLES.

Package Contents

  • B4FM Main Unit
  • 36mm HD Ultra Slim Speakers Boom/Button Microphones Boom Microphone Holder
  • Mounting Bracket
  • Clamp Plate
  • Add on Mounting Pad
  • 3M Tape Bracket
  • User Manual/Quick Start Guide
  • USB-C Cable
  • Speaker Pad
  • llen Wrench & Screws  4
  • Rubber Pad for Clamp Plate 2
  • Dismounting Stick

LEXIN-B4FM-EN Motorcycle Bluetooth Headset 1

Installation Instructions

Installing Bracket for B4FM to Helmet  With Screws

LEXIN-B4FM-EN Motorcycle Bluetooth Headset 2

Mount the bracket between the internal padding and external shell of the helmet. Tighten the two screws between the bracket and Mounting Pad by using the included Allen wrench.

Note
According to the thickness of your helmet shell to add  plastic mounting pad on position and please use the two longer screws, if not, please use two shorter screws.

With Adhesive Pad

If you don’t want to use the clamp plate mounting bracket or you have some problems with using it, you can use the 3M tape bracket to adhere it onto the helmet. Just peel off the protective backing sheet of the 3M tape bracket and adhere the bracket onto the helmet. Press for 15s and to allow the glue 24hours to dry.

Note
Even though the 3M Tape bracket is provided for convenience, LEXIN recommends using the bracket mounting. The 3M Tape bracket is offered as an option that you may use at your own risk and responsibility, LEXIN does not assume any responsibility for use of it.

Mounting the 84FM Unit of Bracket

Mount the B4FM main unit on the bracket. Slide the main unit down onto the bracket until it clicks firmly into the bottom portion of the bracket.

LEXIN-B4FM-EN Motorcycle Bluetooth Headset 4

To remove the main unit from the bracket, use the Dismounting Stick to insert it between B4FM unit and the mounting bracket, then push the B4FM main unit up from the bracket.

LEXIN-B4FM-EN Motorcycle Bluetooth Headset 5

Installing Speakers

Note
The speaker with the shorter wire is for the left ear and the speaker with the longer wire is for the right ear, this will enhance the FM radio reception as well.

Step 1

Place the one half of the speakers velcro pad into the helmets inner padding.

Step 2

Push the speakers firmly against the velcro pads. If the helmet has deep ear pockets, you can use the provided spacers to place the speakers closer.

Step 3

Hide the wires between the helmet liner and shell.

Note

For helmets with deep ear pockets, you can use the included speaker pads to increase the thickness of speakers.

Installing Microphone

Note
The button microphone and boom microphone can be interchanged between full face or open face helmet. Choosing between the two is based on your preference and what fits best in the helmet(s).

Full Face Helmet/Button Microphone
Step 1

Locate an area in the center of the mouth section of the helmet to install and adhere half of the microphone velcro pad.

Step 2

Attach the button microphone to the attached velcro.

Step 3

Connect it to the headphone connector from the left.

Open Face Helmet/Boom Microphone

Step 1

Adhere one half of the velcro pad to the base of the microphone and the other half to inside of the helmet under padding.

Step 2

Adjust the direction of the microphone so that the triangular mark on the microphone is pointing towards your mouth.

Step 3

Use the boom microphone holder for additional support to the microphone if necessary.

General Operation Instructions

Power on/off Hold +  menu  for 1 second simultaneously.

LEXIN-B4FM-EN Motorcycle Bluetooth Headset 10

Powering On/Off

Power On

Long press the Power Button and Intercom Button for about 1 second to power on. The LED will blink blue only. The speaker will report power on and the current battery level.

Power Off

Long press the Power Button and Intercom Button for about 1 second to power off. The LED will blink red only. The speaker will report power off.

Battery

Charging

Plug the USB-C cable into the USB-C port of the main unit and plug USB into the USB port on any DC SV power supply to charge, such as mobile phone charger, computer, laptop or power bank, Etc. The LED turns red while charging and then turns blue when the main unit is fully charged. It takes about3 hours to be completely charged.

Low Battery Alert

The device will notify you when the battery life drops low (below 30%). It will remind you every 5 minutes with a voice alert until the device powers off. This indicates around 1-1.Sh of use remains. It will automatically shut down when the battery is below 20%.

Battery Life Prompt

Every time you turn on the unit, it will automatically report the current battery life. While in standby mode, long press the Down Button for about 1 second, the B4FM device will prompt the current battery life.

Note
It will report one of five levels: 100%, 80%, 50%, 30%, LOW.

Pairing B4FM with Bluetooth Devices

Note
In the group intercom mode, one LX-B4FM device can connect up to two LX-B4FM devices and one mobile phone at the same time. It can automatically connect to your last paired device as long as Bluetooth is enabled or when the device is not connected and is in standby mode, click the Power Button to connect to the Bluetooth device.

Pairing Phone

Step 1

While Powered off, long press the Power Button for about 5 seconds until the LED light flash blue and red alternately to enter pairing mode.

Note
Please do not use the Intercom Button instead of Power Button pairing your phone and GPS devices.

Step 2

Go to Bluetooth settings on your phone. Select “LX-B4FM”, Some mobile phone may need PIN. Enter “0000” for the PIN if needed;

Step 3

Please confirm your phone if the pairing is completed;

Note
The LED will blink blue on B4FM device which indicates the connection is completed.

Pairing Bluetooth GPS Navigation

Step 1
While powered off, long press the Power Button for about 5 seconds until the LED light flash blue and red alternately to enter pairing mode.

Step 2

Follow pairing instructions for your specific GPS Navigation to connect to B4FM;

Note
You will be able to listen to Bluetooth voice instructions from Bluetooth GPS navigation once paired.

Phone calls

Answer Call

Click the Power Button to answer when phone call is coming.

Auto Answer

Incoming calls will automatically be answered after 12 seconds.

Preset On/Off Automatic Answering

With power on state, long press the Up Button for about 5 seconds, the blue light quick flashes 3 times, indicating that automatic answering is on, or long press the Up Button for about 5 seconds the red light quick flashes 3 times, indicating that automatic answering is off.

End Call

Click the Power Button to end the call.

Decline Call

Double click the Power Button to reject the call.

Redial

When in standby mode, double click the Up Button, the last phone call will redial.

Voice Dial

While the device was paired with your phone, double click the Down Button to activate Siri or S-Voice. Simply speak the name from your phone list to dial.

Volume and Music Controls

Volume Up/Down: Long Press the Volume Up or Down Button, and it will prompt both when volume is maximum and minimum.

Note

  1. Only when in the music playing mode/FM Radio Mode/Intercom Mode/Phone Call status that you can adjust the volume.
  2. When listen to the audio sources from your phone, you have to adjust the volume on your phone to get louder volumes.
  3.  Please single click the volume button to adjust the volume gradually, and long press the volume button to adjust the volume continuously.
Pause/Play

Click the Power Button to pause a song, click the Power Button again to resume playing.

Change Song

Double click the Up Button for next song, double click the Volume Down Button for the previous song.

Music Sharing

A B4FM device (A) that is playing music can share music to another B4FM device (B). When device A is playing music, double click Power Button on device A to enter music sharing mode. Then make sure device Bis in standby state, double click Power Button on device B to search and connect device A, it will play the same music automatical­ly once connected.

Stop Music Sharing

To quit music sharing mode, double click Power Button on either B4FM device.

Intercom Connection

The B4FM Bluetooth headsets use full-duplex Bluetooth intercom talk, pairing group internal intercom, divided into 4-way intercom mode and multi-way intercom mode, multi-way intercom mode can achieve up to 10 riders to be connected.

Note
Prior to pairing B4FM units for communications and riding, we strongly suggest that existing connections be cleared from unit. To clear existing connections, long press the Up and Down Button together for about 1 second until the red LED flashes quickly, all previous connections will be cleared from the unit. Every time you turn on the B4FM device, the default is 4-way intercom mode, to switch into the multi-way intercom mode which is for more than 5 riders including 5 riders), in the standby state, you need to long-press Power Button for about 8 seconds on all units, there will be a beep sound and the indicator light quick flashes red at the same time. There is no memory function for this operation, so you have to switch it every time when connects over 5 units.

Bluetooth Intercom Pairing & Connection

2 Way Pairing
  • Press the Intercom Button to pair2 B4FM devices.
  • Power on two B4FM units.
  • Long press the Intercom Button on both two units about 1 second.
  • LED of both two units will flash red and blue alternately which indicate they enter pairing mode.

LEXIN-B4FM-EN Motorcycle Bluetooth Headset 11

Unit One

Long press the Intercom Button about 1 second until LED flash red and blue.

Unit Two

Long press the Intercom Button about 1 second until LED flash red and blue.

Click the Intercom Button on either unit to search and pair the other unit, the LED light flash blue quickly. Once pairing is completed, the LED will blink blue slowly on both two units.

LEXIN-B4FM-EN Motorcycle Bluetooth Headset 12

After pairing is completed, LED of both two units will flash blue slowly and voice prompt pairing successful.

Note
If you only need to pair two B4FM devices, you only need to complete Step CD, and then start the intercom talk .

Start the intercom talk

Once the pairing is successful, click the intercom button on any one of these units to start an intercom talk. When in intercom mode, the LED light will blink blue and red simultaneously. Click the Power Button on any one of these units to make the device temporarily disconnect the current intercom. Click the Intercom Button on any one of these units again to resume the intercom talk.

3 Way Pairing

While completed Step CD, units 1&2 are paired, press the Intercom Button and down button to pair the second and third B4FM devices. Power on both the second B4FM unit and the third B4FM unit. Long press the Intercom Button and Down Button on both two units about 1 second. The LED of both two units will flash red and blue alternately which indicate they enter pairing mode.

LEXIN-B4FM-EN Motorcycle Bluetooth Headset 13

Unit Two

Long press the Intercom Button & Down Button about 1 second until LED flash red and blue.

Unit Three

Long press the Intercom Button & Down Button about 1 second until LED flash red and blue. Click the Intercom Button on either unit to search and pair the other unit, the LED light flash blue quickly. Once pairing is completed, the LED will blink blue slowly on these three units.

LEXIN-B4FM-EN Motorcycle Bluetooth Headset 14

After pairing is completed, LED of these three units will flash blue slowly and voice prompt pairing completed.

Note

  1. If you only need to pair three B4FM devices, you only need to complete and then start the intercom talk .
  2. If the second device is disconnected, other devices will also be disconnected.

Start the intercom talk

Once the pairing is successful, click the intercom button on any one of these units to start an intercom talk. When in intercom mode, the LED light will blink blue and red simultaneously. Click the Power Button on any one of these units to make the device temporarily disconnect the current intercom; Click the Intercom Button on any one of these units again to resume the intercom talk.

Four-way Pairing

While completed Step  and Step, units 1&2&3 are paired, press the Intercom Button to pair the third and forth B4FM devices. On the standby mode, long press the Intercom Button on the third and the fourth units about one second, the voice will prompt pairing, then the LED light on both two units will flash red and blue alternately which indicate enter pairing mode.

LEXIN-B4FM-EN Motorcycle Bluetooth Headset 15

Click the Intercom Button on either unit to search and pair the other unit, the LED light flash blue quickly. Once pairing is completed, the LED will blink blue slowly on these four units.

LED of  four units

After pairing is completed, LED of these four units will flash blue slowly and voice prompt pairing completed

LEXIN-B4FM-EN Motorcycle Bluetooth Headset 16

Unit Three

Click the Intercom Button until LED flash blue quickly.

Unit Four

LED flash blue quickly.

Start the intercom talk

Once the pairing is successful, click the intercom button on any one of these units to start an intercom talk. When in intercom mode, the LED light will blink blue and red simultaneously. Click the Power Button on any one of these units to make the device temporarily disconnect the current intercom. Click the Intercom Button on any one of these units again to resume the intercom talk.

Note
When one of the devices disconnects, the intercom group will be divided into two separate groups from the unit. Click the intercom button again to re- establish the intercom, the two independent intercom groups will be reconnected.

Multi-way group intercom

t
Long press the power button about 8 seconds on each unit till the red light flash quickly then it will switch to multi-way group intercom mode.  Every time you turn on the B4FM device, the default is 4-way intercom mode, and to switch into the multi-way intercom mode which is for more than five riders including five riders, in the standby state, you need to long press Power Button for about 8 seconds on all units, there will be a beep and the indicator light flashes red quickly at the same time. There is no memory function for this operation, the default 4-way intercom mode is used every time you turn on the device, so you need to long press Power Button for about 8 seconds on all units to switch it into mutil way intercom mode every time when you need it.

Group Pairing

Repeat the following steps to pair with more than five B4FM devices.

LEXIN-B4FM-EN Motorcycle Bluetooth Headset 18

Note
Each B4FM device can only be paired with two other B4FM devices at the same time, that means, we pair the unit one after another in series to realize multiple group connections. For example, if unit three is paired with unit two and unit four, and it will not be able to pair with other devices.

Start the intercom talk

Once the pairing is successful, click the intercom button on any one of these units to start an intercom talk. When in intercom mode, the LED light will blink blue and red simultaneously. Click the Power Button on any one of these units to make the device temporarily disconnect the current intercom; Click the Intercom Button on any one of these units again to resume the intercom talk.

Note
The intercom talk in the group will be divided into 2 separate intercom groups from the disconnected unit. Click the intercom button again to re-establish the intercom, the two independent intercom groups will be reconnected.

Clear The Pairing

Long press the Up and Down Button at the same time for about 1 second to clear the pairing, the red light will flash quickly.

Universal Pairing

To enter pairing mode

Step 1

With power on state, long press the Intercom Button for about 1 second until the LED begins flashing blue and red alternately;

Step 2

Follow your other Bluetooth device pairing instructions to enter pairing mode; Step 3: Click the Intercom Button on B4FM to search the other device and the LED light will flash blue and red quickly. After the pairing is completed, the LED light returns to the blue light flashing slowly;

Step 4

To initiate universal intercom, click the Up Button and Down Button together to initiate intercom talk;

Step 5

Click the Power Button to end the intercom talk.

FM Radio On/Off

Turn On FM Radio

Long press the Power Button for about 1 second to enter radio function.

Turn Off FM Radio

When the radio is on, Long press the Power Button for about 1 second to end radio function.

FM Radio Station Search

Turn up
Double click the Down Button, the voice will prompt to adjust the radio station upwards.

Turn down
Double click the Up Button, and the voice will prompt to adjust the radio station downward.

Store up to 6 FM Radio Stations

In FM radio mode, when a favorite station is found, double click the Power Button to save it and there will be a tone to prompt. Support storing up to 6 FM radio stations. Once 6 stations have been saved, saving a new station will overwrite the oldest saved station. Click the Power Button to cycle through the saved station.

Maintenance & Certification

Maintenance and Care

The B4FM should be treated with care and the following suggestions will help maintain your Warranty

  • Do not use or store the device in dusty or dirty environments.
  • Moving parts and electronic components can be damaged.
  • Do not store the device in high heat areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp or melt certain plastics.
  • Do not store the device in cold temperature areas.
  • When the device returns to its normal temperature, moisture can form inside the device and damage electronic circuit boards.
  • Do not attempt to open the B4FM case.
  • Do not drop or knock the device. Rough handling can break internal circuit boards and fine mechanics.
  • Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
  • Do not paint the device. Paint can clog the moving parts and prevent proper operation.
  • These suggestions apply equally to the headset main unit, speaker-microphone clamp unit, and power charger.

Warranty
LEXIN warrants that this product shall conform to and perform in accordance with published technical specifications and the accompanying written materials, and shall be free of defects in materials and workmanship, for a period of one year from the date of purchase by the first consumer purchaser of the Product. The limited warranty extends only to the original consumer purchaser of the Product and is not assignable or transferable to any subsequent purchaser/end-user. This warranty is limited to the repair or replacement, at LEXIN s discretion, of defective or non-conforming Product, and LEXIN shall not be responsible for the failure of the Product to perform specified functions, or any other non- conformance caused by or attributable to any misapplication or misuse of the Product  failure of Customer to adhere to any of LEXIN’ s specifications or instructions  neglect of, abuse of, or accident to, the Product or  any associated or complementary equipment or software not furnished by LEXIN. Limited warranty service may be obtained by delivering the Product to LEXIN or to the international distributor it was purchased through and providing proof of purchase or receipt date. Customer agrees to insure the Product or assume the risk of loss or damage in transit, to prepay shipping charges to LEXIN, and to use the original shipping container or equivalent.

Waivers and General Release

By using the Product, you will waive substantial legal rights including, the right to use. Please read the following carefully before using the device. By using the Product, you agree to this agreement and forfeit the right to pursue legal action. By using the Product, you are irrevocably releasing, indemnifying from any liability, loss, claim and expense (including attorney’s fees) and holding LEXIN harmless for any bodily injuries, harm or death as well as losses or damages in goods, to any vehicles including your own, or to any property or asset that belong to you or to third parties, any of which may result from using the Product under any circumstances or conditions and irrespective of jurisdiction. You, your heirs, legal representatives, successors or assigns, hereby voluntarily and forever release, discharge, indemnify and hold harmless LEXIN from any and all litigation, claims, debts, demands, actions and liability which may arise, directly or indirectly, from using the Product for any distress, pain, suffering, discomfort, loss, injury, death, damages to or in respect to any person or property however caused, WHETHER ARISING FROM THE NEGLIGENCE OR OTHERWISE, and which may hereafter accrue to you on some future date as a result of said use, to the fullest extent permitted by law.
You fully understand and assume the risks in using the Product, including risk of negligent acts or omissions by others. All risks for operating the Product are assumed solely by the user of the Product. You confirm that you are physically capable to use the Product and that you have no medical conditions or needs that may infringe upon your abilities to do so in a safe manner. You confirm that you are at least eighteen (18) years of age and that you have been advised of the risks associated with the use of the Product. You further confirm that you will not consume any alcohol that may affect your alertness or any mind-altering substance, and will not carry, use or consume these substances before or during the use of the Product. You fully acknowledge our warnings and understand that

  • Risks and dangers exist in using the Product while in traffic, including but not limited to injury or illness, strains, fractures, partial and/or total paralysis, death or other ailments that could cause serious disability;
  • These risks and dangers may be caused by the negligence of the manufacturers or its agents or any third party involved in designing or manufacturing the Product.
  • These risks and dangers may arise from foreseeable or unforeseeable causes.
  • You hereby assume all risks and dangers and all responsibility for any losses and/ or damages, whether caused in whole or in part by the negligence or other conduct of others, including LEXIN.
  • By using the Product, you confirm that you have read this release of liability and fully understand and accept its terms and conditions.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. The antenna used for th is transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures search for FCC ID: 2ARGO-LXB4FM This device complies with Industry Canada licence exempt RSS standards. Operation is subject to the following two conditions: (l)this device may not cause interference, and(2) this device must accept any interference, including interference that may cause undesired operation of the device. This EUT is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209. This equipment should be installed and operated with minimum distance of 1cm between the radiator and your body. This device and its antenna(s)must not be co-located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals