iTrybrand VT08F GPS Vehicle Tracker User Guide
- June 6, 2024
- iTrybrand
Table of Contents
GPS Vehicle Tracker
User Guide
(Version V2.1)
At
a Glance
- Overview
- Accessories Power cable/Relay/Microphone/SOS alarm Button
- Wiring Diagram
**Getting Started
**
Installing the SIM card
Important:
- A SIM card is required in order to use cellular services when connecting to GSM/LTE networks.
- Keep the SIM card cellular network available.
- Note down the SIM card phone numbers which is device contacting numbers.
Notice: Please install the SIM card before switching on the device.
Setting up and activating the device
To set up and activate the device, you should send SMS to devise numbers by
mobile phone.
Setting server SMS: SERVER,1,vt.protrack365.com,8842,0#
Installing the device
Connect according to wires to your car by referring to Wiring Diagram in
Install the device in the following three suggested places:
Important:
- Make it covert for security factors.
- Keep away from high power electrical devices, such as reversing radar, anti-theft devices or other vehicle communication equipment which may affect the device signal.
- Keep the device front face up & No metallic cases above the device which may affect the signal as well. Such as the windshield which is pasted with metal thermal-protective coating or heating coating.
Checking location
3.1 Via SMS
WHERE#
3.2 Via tracking platform
www.protrack365.com
Ask your distributor for a log-in account and password.
Basic
4.1 LED indication
4.1 1 Red LED -Power status
| Slow flashing | Normal working (backup battery) |
|---|---|
| Solid bright | Normal working (external power supplying) |
| Off | Power off |
4.1.2 Green LED -Network status
| Quick flashing | GSM/LTE initialization |
|---|---|
| Slow flashing | Normal working with GSM/LTE network |
| Off | No GSM/LTE signal |
4.1.3 Blue LED -GPS status
| Quick flashing | Searching GPS signal |
|---|---|
| Slow flashing | Normal working with GPS fixed |
| Off | No GPS fixed |
4.2 Power/ACC/Tele-cutoff (petrol/electricity) control line (4 pin)
4.2.1 The standard voltage is 9V-90VDC. Please use the power line which is
provided by the manufacturer. The red line is positive. The black line is
negative. The negative should be earth alone or link iron during installing.
Do not connect it to other ground wires.
4.2.2 ACC line (orange) is connected to the ACC switch of the vehicle. Please
make sure to connect the ACC line. The tracker will decide whether to enter
ignition detection according to ACC status. It does not connect to the ACC
line, the device will enter ignition detection status. If the vehicle vibrates
when moving, it will activate the vibration alarm. If there is no need for the
theft-proof function, connect the ACC line to the positive in parallel and
keep a high level.
4.2.3 Tele-cutoff (petrol/ electricity) control line (yellow) is connected to
pin 86 of the Tele-cutoff (petrol/ electricity) relay (equal to the yellow
line of the relay socket).
4.3 Input and Output cable (3 pins) Firmware updating interface/expanded
function to reserve space.
4.4 MIC line (2 pins) Externally connect to microphone for voice monitor
function
4.5 SOS line (2 pins) Externally connected to SOS switch for SOS function.
Alarm management
*When any kinds of alarms happened, the device will send alarm SMS&CALL SOS numbers.
5.1 Vibration Alarm When ACC is off and some vibration happened, the device
will alarm.
5.2 Cut-off alarm When external power is cut, the device will alarm.
5.3 Geo-fence alarm After setting the geofence range, if the device comes in &
out of the range, it will alarm.
5.4 Low-power alarm When external power is cut, the device will keep working
with its backup battery and when its battery is too low, the device will
alarm.
5.5 Movement alarm When ACC is off, if the vehicle is moved, the device will
alarm.
Note : For other alarm settings and parameter settings, please check the
command list provided by the supplier.
**Troubleshooting
**
6.1 When a device in the background display not on-line or off-line, First observe the device 3 indicator is normal, according to the device lights status to judge device work condition, if the red light flashes, the green light is not bright, please check
that the SIM card is installed correctly, if the installation is no problem, please replace the SIM card test again. Under no condition to observe the situation, use mobile phone dial SIM card device number, if not connect successful, indicating that the device Area is no GSM/LTE signal or signal is weak, please try it again in a good signal place; if the device is an insufficient balance or out of service, please try again after recharge; if connect successfully, please consult the appropriate operator if SIM card is open cellular network function; if not connected, prompt power off, please check that the device is installed properly.
6.2 When the GPS signal reception is abnormal, please take it into the broad
place positioning, general first positioning needs 1-2 minutes. If a long time
does not position, please check the device installation location if meets the
requirements, the normal installation without metal shielding.
6.3 When the GSM/LTE signal reception is abnormal, please check the device SIM
card is installed correctly; or the location may not cover GSM/LTE signal
(such as a basement), please use it in the place where signal coverage.
6.4 When power-up, the red power light is off, please check the wiring is
correct, and after excluding the internal device problem then can power up
again.
**Maintain Information
**
Customer Name:…………………………………………
Tel: …………………………………………………………….
Add: ………………………………………………..
IMEI:……………………………………………
Purchase Date:……………………………………..
Maintain Records
| Date | Problem Description | Records | Debug Engineer |
|---|---|---|---|
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>