Origin 21 W3006LMB Brushed Gold Iron Corner Curtain Rod with Finials Instruction Manual
- June 13, 2024
- Origin 21
Table of Contents
W3006LMB Brushed Gold Iron Corner Curtain Rod with Finials
Instruction Manual
W3006LMB Brushed Gold Iron Corner Curtain Rod with Finials
ITEM #5276581, #5276583, #5276585
DRAPERY ROD SET
MODEL #W3006LMB, #W3006LBN, #W3006LBG
ORIGIN 21 and logo design are trademarks or
registered trademarks of LF, LLC. All rights reserved.
Thank you for purchasing this ORIGIN 21 product. We’ve created these easy-to-
follow instructions to ensure you spend your time enjoying the product instead
of putting it together. if you need more information than what is provided
here, please visit Lowes.com, search the item number and refer to the Guides &
Documents tab on the product’s page.
If the item is no longer for sale, or if you have any questions or problems,
please call our customer service department at
888-251-1026, 8 a.m. – 8 p.m. EST,
Monday – Sunday. You could also contact us at
ascs@lowes.com
TROUBLESHOOTING
| PROBLEM | POSSIBLE CAUSE | CORRECTIVE ACTION |
|---|---|---|
| Cannot access the top screw hole on brackets to install properly. | Supporting | |
| bracket arm is in the way. | Swivel the arm to the side and install the top |
screw hole
BEFORE swiveling the bracket arm back to original position and installing the
bottom screw hole.
Rod does not extend to desired length / Rod is too short for desired length.|
Only two rods were used, and the third larger
diameter rod was not applied.| Add the third larger diameter rod to form a
longer 3-piece telescopic rod (see step 4).
Rod is too long for desired length.| Three rods were all used, but only two
rods are needed.| Discard one larger diameter rod and install just the 2-piece
telescopic rod (see step 4).
Rods slide / slip when curtain panels are pulled left and right.| The rods are
not properly secured in the brackets.| Tighten the rod-securing-screws on the
brackets (see step 6).
PREPARATION
Before beginning installation of product, make sure all parts are present.
Compare parts with package contents list and hardware contents list. If any
part is missing or damaged, do not attempt to assemble or install the product.
Estimated Assembly Time: 15 minutes.
TOOLS REQUIRED
CARE AND MAINTENANCE
Dust gently with dry cloth.
Periodically check to make sure all components are properly positioned, free
from damage and firmly connected.
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble or
install the product.
FEELING CONFIDENT? START YOUR NEXT PROJECT
• Visit lowes.com for more information.
PACKAGE CONTENTS
|
---|---
Larger bracket/Sported grandee x 1 (noted with “L” at the back of bracket)|
Smaller bracket/Sported paquebot x 1 (noted with “S” at the back of bracket)
HARDWARE CONTENTS
INSTALLATION OVERVIEW
Unfasten screws between rods and side brackets [A&B] to remove side brackets.
Please note the removed screws and washers will be used later, so please keep
them within sight.
Use both brackets [A&B] as guides to mark desired locations on wall for
mounting screws. Use level to ensure screw holes alignment.
Stud installation is recommended, use a stud finder to locate stud. If no
studs are present, provided drywall anchors can be used.
For
wood/stud installations, anchors [CC] are not required. Pre drill 3/32”
pilot holes at market locations.
For drywall/paneling installations, anchors [CC] are required.
Predrill 1/4” pilot holes at market locations, then screw anchors [CC] into
pilot holes.
INSTALLATION OVERVIEW
For installation rod length shorter than 96” (for 72”-144” rod set), attach
drapery panel (sold separately) onto outer rod [C], place rods on center
bracket [AA] and secure outer rod [C] onto larger bracket [A] with the washer
and screw removed from Step 1. Repeat this operation on the other side for
inner rod [D] and smaller bracket [B]. 
For installation rod length wider than 96” (for 72”-144” rod set), attach drapery panel (sold separately) onto outer rod [C], place rods on center bracket [AA] and secure rod onto larger bracket [A] with the washer and screw removed from Step 1. Insert inner rod [D] into the other outer rod [C] to extend rod length. Attach another drapery panel onto last outer rod [C], and secure rod onto smaller bracket [B] with washer and screw.
Printed in Vietnam