aspire NX100 Classic Box Mod User Manual

: June 13, 2024
: aspire

Table of Contents

aspire NX100 Classic Box Mod
Product Information
PRODUCT OVERVIEW
Specifications
Protection Features
NX100 Button Functions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

aspire NX100 Classic Box Mod

aspire-NX100-Classic-Box-Mod-PRODUCT

Product Information

Model: NX100 mod
Connector: Spring-loaded 510 connector
Buttons: Fire button, W Button, T Button
Screen: 0.9 inch TFT color screen
Charging Port: Micro-USB port
Battery: 3.7V single 26650 high-rate discharge battery
Protection Features:
- Automatic Cut Off
- Short Circuit Protection
- Low Resistance Protection
- Overheat Protection
- Overcharge Protection
- Over-Discharge Protection

Specifications

Wattage Range: 1-100W
Output Voltage Range : 0.00-8.50V
Resistance Parameters: NX100 can fire coil resistance from 0.1 to 3.5 (Wattage may be less than 100 watts when coil resistance exceeds 0.1-0.4)
Continuous Fire Time: Adjustable from 5s to 15s
Screen: 0.9 inch TFT color screen
Firmware Update: Via Micro-USB port
Dimensions: 304778.5mm
Battery: 3.7V single 26650 high-rate discharge battery

Product Usage Instructions

To lock/unlock the mod: Click the fire button 5 times.
To enter or exit stealth mode: Click the fire button 3 times.
To change between different modes (VV, VW, Bypass, and CFBP): Press the W button.
To change coil materials and TCR settings under TC mode: Press the T button.
To increase or decrease Voltage, Temperature, or Wattage: Use the + and – buttons.
To fire or confirm: Press the fire button.
To customize Firing Button Profiles (CFBP): Press the W button for 1.5 seconds to enter the CFBP interface. Use the W or T button to set time, and use the + and – buttons to adjust wattage. Press the fire button to save settings.
To charge the mod: Connect your NX100 mod to the charger. The screen will show a flashing battery icon. When the battery charge reaches 4.2V or is fully charged, the mod will stop charging and the screen will remain off. Note: The battery cannot be replaced while charging. Unplug the USB cable before changing your battery.
To upgrade firmware: Download the driver software from the Aspire website. Connect your NX100 to your PC. The driver will detect your NX mod automatically. Choose the correct firmware file and click Update to upgrade your NX mod.
To use an 18650 battery instead of a 26650 battery: The NX100 comes with an 18650 battery adapter sleeve. Install the battery adapter sleeve and select the battery type (18650 or 26650) displayed on the screen. Note: The maximum wattage output when using the 18650 battery is 75W, while the maximum wattage output when using a 26650 battery is 100W.

PRODUCT OVERVIEW

$aspire-NX100-Classic-Box-Mod-FIG- $1$$

Specifications

Wattage Range: 1-100W
Output Voltage Range: 0.00-8.50V
Resistance Parameters: While in both Wattage Mode and TC Mode, NX100 can fire coil resistance from 0.1Ω to 3.5Ω (Wattage may be less than 100 watts when coil resistance exceeds 0.1-0.4Ω).
- Continuous Fire Time can be adjusted from 5s to15s
Charging Port: Micro-USB charging port
Screen: 0.9 inch TFT color screen
- Firmware update via Micro-USB port
Dimensions: 304778.5mm
Battery: 3.7V single 26650 high-rate discharge battery

Temperature Control

Temperature Range (F): 200-600F
Temperature Range (C): 100-315℃

Protection Features

Automatic Cut Off
Short Circuit Protection
Low Resistance Protection
Overheat Protection
Over charge Protection
Over-Discharge Protection

Note:

SS under TC Mode only supports SS316L coils.
The mod supports passthrough charging. To lengthen the life of the mod, we do not recommend vaping while charging (passthrough).

NX100 Button Functions

Click fire button

5 times

| To Lock/Unlock Mod
---|---
Click the fire button 3 times| To enter or exit stealth mode
“W” + “+”| Lock and Unlock

buttons

“W”

| To change between VV, VW, Bypass, and CFBP(C1, C2, C3) modes

“T”

| To change coil materials and TCR settings(M1,M2,M3) under TC mode

“+” / “-”

| To increase or decrease Voltage, Temperature, Wattage
Fire button| To fire or to Confirm

Customizable Firing Button Profiles (CFBP)

Customizable Firing Button Profiles (CFBP) Intro:

The CFBP feature allows for heat ramp-up (power curve) to be fine-tuned.
Press the W button to select VW, VV, Bypass, C1, C2, and C3. C1, C2, C3 are CFBP. While in CFBP, pressing the W button for 1.5 seconds will bring you to the CFBP interface. While in the CFBP setting interface, press the W or T button to set time, press the “+” button to increase wattage, and press the “-” button to decrease wattage. To save settings simply press the fire button.

Charging

Connect your NX100 mod to the charger and the screen will show a flashing battery icon. When the battery charge reaches 4.2V or is fully charged, the mod will stop charging and the screen will remain off.
The battery can not be replaced while charging. Please unplug the USB cable before changing your battery.
When the battery charge drops below 0.5V or the battery is incorrectly installed the mod will stop charging.
To accomplish 2the A charge current, the adaptor output should be 5V/2A.

Firmware Upgrade

Download the driver software from Aspire website: http://www.aspirecig.com/upgrade/
Connect your NX100 to your PC. The driver will detect your NX mod automatically.
Click “OpenFile” to choose the correct firmware file.
Click “Update” to upgrade your NX mod.
If it failed during the update process please repeat step 3 to step 4.

The NX100 also comes with an 18650 battery adapter sleeve. The 18650 adapter sleeve allows you to use the 18650 battery instead of the 26650 battery. Upon battery installation, the NX100 screen will display 2 battery icons labeled 18650 and 26650. Please select the battery type you inserted.

Note : The maximum wattage output when using the 18650 battery is 75W, while the maximum wattage output when using a 26650 battery is 100W.

To learn more about your products and how to use them, please visit: www.aspirecig.com

https://manual-hub.com/