Guangdong Anjou Robot Technology L100 Pro Robot Vacuum Cleaner User Manual

Guangdong Anjou Robot Technology
100 Pro Robot Vacuum Cleaner
User Manual

Read this user manual carefully before using this product and save it properly for further reference.

Important Safety Instructions

WARNING: TO REDUCE THE RISK OF INJURY OR DAMAGE, READ THE FOLLOWING SAFETY PRECAUTIONS WHEN SE I I ING UP, USING AND MAINTAINING YOUR ROBOT.

Cautions

• This product is designed for indoor floor cleaning only, do not use it outdoors (such as on an open-ended terrace), on any surface other than the ground (such as a sofa ), or in any commercial or industrial environment
• Do not use this product on elevated surfaces without barriers such as the floor of a loft, an open-ended terrace, or on top of furniture.
• Do not use the product when the ambient temperature is higher than 104°F (40°C), lower than 39°F (4°C), or if there are liquids or tacky substances on the floor.
• Before using the product, move wires off the ground or place them to the side to prevent them being pulled on by the cleaner.
• To prevent blocking the product and to avoid damage to valuables, remove light-weight items (such as plastic bags) and fragile objects (such as vases) from the floor before cleaning.
• Children should be supervised to ensure that they do not play with the appliance.
• This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the product by a person responsible for their safety .
• This product can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved. Children shall not play with the Cleaning and user maintenance shall not be made by children without supervision (EU).

Battery and Charging

• Do not charge non-rechargeable batteries.
• For the purposes of recharging the battery, only use the detachable supply unit robot provided with this product.
• Do not dismantle, repair or modify the battery or charging dock
• Keep the charging dock away from heat (such as heating vents).
• The battery must be removed from the appliance before it is scrapped
• The product must be disconnected from the supply mains when removing the battery.
• The battery must be disposed of safely. Do not discard waste batteries, leave them with a professional recycling organization.
• Do not wipe or clean the charger prongs with a wet cloth or wet hands.
• If the power cord is damaged, stop using it immediately. It must be replaced by the manufacturer, service agent or similarly qualified persons to avoid a hazard.

Cautions

• Keep the main brush cleaning tools out of reach of children.
• Do not place any object (including children and pets) on the product, whether it is in operation or not
• Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts.
• Do not use the product on burning objects (such as cigarette butts).
• Do not use the product on high pile carpets (product effectiveness may also be reduced on dark carpets).
• Do not use the product to clean hard or sharp objects (such as decoration wastes, glass, and nails).
• Do not carry the product by using the main unit cover, or collision buffer.
• The product must be switched off and the plug must be removed from the socket-outlet before cleaning or maintaining the product.
• Do not use wet cloth or liquids for cleaning the product.
• Do not use the mopping module on carpets.
• Use the product according to the manual, Any loss or damage caused by improper use will be borne by the user.
• This product contains batteries that are only replaceable by skilled persons.

Product Introduction

Top view

Installation Using the robot

1. Remove the EVA foam on each side.
   

2. Place the charging clock against the wall on a flat surface and plug it into the power socket .
   Note:
   • The charging dock should have more than 1.0rr(3.0ft) of clearance on each side. and more than 2.0m (6. Oft) in the front.
   • If the patter cable is vertical to the ground. st may be caught by the robot. causing the charging dock to be disconnected.
   • The charging dock indicator is on when the charging dock is electrified, and off when the robot is charging.

3. Turn the robot over to install the side brushes.
   

Install the side brushes

Install the side brushes on both sides of the roller at the bottom of the main unit. Pick up the side brushes with your hands and aim at the hole of the side brush installed on the base (note that the square column and the square hole correspond to each other), press it down to hear a “click” sound, indicating that the side brush is installed in place.

Charging

• Auto: After cleaning 1 the robot will automatically return to the charging dock to recharge. The button light keeps flashing.
• Manual: In pause mode, press the button to send the robot back to the charging dock. If the robot is stuck or can not find the charging dock, place the robot directly on the dock to recharge it.
• Recharge by remote control.

Note:

• The battery is fully charged to prolong the battery life.
  5 hours charging time for the first time.

• Please keep charging dock power on. Or the robot can re: fins the charging dock.

• Close the Tuya App to reduce tablet/ phone battery consumption when the vacuum robot is cleaning.

• The furniture must be at least 98 mm in height for the machine to to pass through.

1. Power on and charge
   Placing the robot onto the charging dock and power on.
   Turning on the robot defaults.
   The robot will turn on when turning on the main power switch if the robot is not connected to the charging dock_ The power indicator lights up.
   Turn off the main power switch to turn off the robot if the robot is not onto the charging dock.

2. Pause
   When the robot is cleaning, press the (▶)button to pause it.
   Then press (▶)the button to continue cleaning or the button to stop the current cleaning. Press the button twice to return it to the charging dock

3. Sleep
   If the robot is paused and does not connect to the charging dock for over 10 minutes, it will go to sleep, press any button to wake it back up.

Zone Cleaning (Only App operation support )
Use the app to draw a specific zone for the robot to clean. Then, the robot will only clean the designated zone. After cleaning, the robot will return to the charging dock automatically. 

Selective Room Cleaning (Only App operation support )
Select specific rooms for cleaning in the app. In this mode, the robot will only dean the selected rooms. After cleaning, the robot will return to the charging dock automatically.
Note:

• A full map must be created before this function can be used.
• After cleaning starts. the robot may move beyond the defined areas. Make sure there are ro obstacles preventing the robot’s access to the target rooms.

Virtual Wall (Only App operation support )
Press virtual wall in APP to draw the virtual wall line. You can use a virtual wall to isolate the areas that do not want to be cleaned.
Note:

• A dry vacuum module can be used on either a smooth or carpeted surface.
• Remove/secure all loose floor mats/rugs in the area being vacuumed.
• A vacuum robot is designed to move across surfaces between 0 mm to 15 mm.
  

App Instruction

As the Tuya App is continuously being updated, your App may appear slightly different than what is pictured in this User Guide. The app needs to be used in the networked state and please connect to the home network first.
Make sure the network is normal. Download

1. Scan the QR code and download the “Tuya Smart APP”. For IOS model phones, search foraTuya Smart” in the APP store to download; For Android model phones, search for Tuya Smart in the app store to download.

http://smart.tuya.com/download

Sign up:
New users enter the registration page by clicking create a new account. Use an unregistered mobile phone number/ email, and set a login password by obtaining a verification code. After registration, you can log in to use.

Log in:
If you have an account, enter your account, and password in the APP login interface to log in.if you forget the password click Forgot Password, enter the registered mobile phone  number/email, and obtain the verification code to log in to the account

Add device:

1. After login click Add Device;

2. Click’Small Appliances “and then-robot vacuum cleaners”.

3. Press the pause button(▶ )for 2-3 seconds for the first time to start the smart network connection until there is a voice prompt.
   (WIFI indicator light flashes quickly);

4. Checktonfirm that the indicator light is flashing fast” and click Next.

5. Show that the robot vacuum cleaner is being added.

6. Click Finish after adding successfully.
   

App interface

1. Cleaning modes “Smart Cleaning’, “Designated Area Cleaning “. Note: Change the cleaning mode, the current cleaning mode must be ended first.
2. Recharging: when the robot is in standby mode or auto cleaning mode, if you press the recharging button, the robot will look for the charging dock for recharging.
   

Setting

Click ” Setting” on the home page to enter more pages and click to enter the corresponding function.

1. Manual control: control the direction button/pause button/start cleaning.
2. Room Manage: Reset or Save the map.
3. Click “seek robot “: the robot will voice prompt ” I am here “
4. Use the app to set start times for scheduled cleanups. Select scheduled cleaning and save the scheduled cleaning time
5. Suction power: Quiet? Normal, Strong.

Can adjust voice volume and switch language.
Setting

1. Click the upper right corner on the main control page to enter the robot settings page. And click to enter the corresponding function.
2. Adding share: Enter the robot account to be shared.
3. Remove device: Click “Remove device” to remove the bound device from this account

Reset WiFi

If your phone cannot connect to the robot because you have changed your router configuration, forgotten your password, or any other reason, press and hold the power button until you hear the ” Resetting WiFi “voice alert.

Note:

• Before setting up Wi-Fi, please make sure that the robot and Wi-Fi network meet the following requirements.
  Wi-Fi setup requirements.

• The robot is fully charged.

• The Wi-Fi status indicator flashes slowly in white.

Wi-Fi network:

• Use the correct wireless network password.
• Do not use VPN ( Virtual Private Network) or proxy server.
• The Wi-Fi router supports 802 .11b/g/n and Ipv 4 protocols. ‘ The router frequency band is 2.4 GHz or dual-frequency router that supports the 2.4 GHz, frequency band. The robot does not support the 5 GHz frequency band.
• If the robot is unable to connect in the 2.4/5GHz dual-band Wi-Fi network, please switch to the 2.4 GHz network for Wi-Fi settings. After the setting is complete, you can switch back.
• When connecting to a hidden network, please make sure to enter the correct network name—SSID (case sensitive ) and connect to a 2.4 GHz wireless network.
• When using a wireless extender/ repeater, please make sure that the network name (SSID) and password are the same as the main network.
• Set the firewall and port of the Wi-Fi router to allow the robot to connect to the App server. Network security requirements:
• Use TKIP, PSK, AES/ CCMP encrypted WPA and WPA 2 network.

Cleaning the Dust bin

Step 1. Press the dust bin release buckle and take out the dust bin, as shown in Figure 1.
Step 2. Use one hand to press and hold the release buckle, and the other hand to open the cover to open the dust bin and remove the dust.
Step 3. Clean the dust bin as shown in Figure 3.
Step 4. Take out the filters and clean the dust on them.
Step 5. The dust bin and filters can be cleaned under running water. (Note: The dust bin and filters can only be put back after they are completely dry.)
Step 6.  After cleaning, reinstall the filters and dose the dust bin cover. Finally, insert the dust bin back into the robot.

Note

• Please open the dust bin upwards to avoid spilling anything inside.
• For a new robot, dean the dust. bin once every three days in the first month- After that, clean it once every week. (It is recommended to replace the filter every 3-6 months  to ensure a better cleaning recur )
• Do not place the filter under direct sunlight.

Maintenance

Main brush assembling and cleaning
Note: When replacing main brush after cleaning- make certain it is firmly seated

Primary filter/sponge foam/HEPA filter cleaning
Take out the primary filter/sponge foam/HEPA filter and the_, can be cleaned under the running water. After cleaning,dry them and re-install them .

Side brush cleaning
A. Use a brush cleaning tool to cut off the entangled debris.
B. Use a clean cloth to clean the side brush. Note- Side brush replacement every 3-6 months is recommended to maintain cleaning quality.
Top of vacuum unit cleaning
When the top of the vacuum unit collects dust and fingerprint, you may wipe and clean it with clean cloth

C. When the side brush cannot be used, please remove the, damaged side brush and replace it in time
Note: Clearing water must be lower than 60 degrees celsius

Omnidirectional wheel cleaning

1. Turn the robot over.
2. Pull out the wheel upwards.
3. Reinstall after cleaning and press firmly.
4. Rinse the axle and the wheel with water to remove any hair and dirt
5. Dry and reinstall the wheel then press it back in place.

Robot sensor and cleaning
Use a soft dry doth to clean the sensors.
Note: Do not touch the sensors directly with liquids such as Ovate and thinner.

Troubleshooting

Error

|

Solution

---|---
The main brush tangled up| Please clear the roller brush
The side brush tangled up| Please clear the side brush
A %heel is abnormal and the robot lammed| Please check the drawing wheels
The dust bin abnormal installation| Please install the dust bin
Abnormal cliff sensor / dirty cliff sensor| Please wipe the cliff sensors
The robot is stuck| Please clean any obstacle around it
Our bumper is stuck| Please check the front bumper
The robot is suspended| Please put the robot back on the ground

FAQs

Val signal is poor Make sure that the robot rs In an area with good Wtfi signal reception only powered or press the recharging button for 3-5 seconds for the first Me to start the smart network connection until there is a Were prompt  1 MB indicatOr light flashes Quickly).
Only 2.46 network Is supported

Product parameters

If the above methods cannot solve the problem, you can try the following:

1. Turn on the power switch on the side of the unit again and restart the machine.
2. If the machine keeps moving backward, please pat the bumper with your hand and restart it.
3. If the machine does not move forward, please check whether the cliff sensor is blocked and lean the dust on the sensor cover.
4. If the problem cannot be solved by restarting, please return the machine to the after-sales service center for repair.

Tips :

1. The laser sweeper can automatically recognize the floor plan. During the cleaning process, it will move in zip zag shape.
2. The laser navigation machine has a repositioning function. When using this function, the machine needs to be paused first and be in the area that has been cleaned, otherwise, the positioning will fail,

The robot Parameters

Charging base
Output voltage| 19V
Charging base output current| 1A

Remark Storage temperature 0-45° C

Docking station parameters

Product parameter

Name and content of hazardous substances in the product

Diphenyl Etnies (PBDE)
Circuit| X| 0| 0| 0| 0| 0
Metal Parts| 0| 0| 0| 0| 0| 0
Plastic Casing| 0| 0| 0| 0| 0| 0
Battery| 0| 0| 0| 0| 0| 0
Other parts| 0| 0| 0| 0| 0| 0
This form is compiled in accordance with the regulations of S j/T 11364.
0 Means that the content of the hazardous substance in all homogeneous materials of the part is below the limit requirement specified in GB/T 26572.
X Means that the hazardous substance at least in a certain homogeneous material of the part exceeds the limit requirement of GB/T 26572.

FCC Warning:

This equipment has been tested and found to comply with the limits for a Class B digital device. pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation_ This equipment generates. uses and can radiate radio frequency energy and. if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. However. there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception. which can be determined by turning the equipment off and on. the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. and C2) this device must accept any interference received_ including interference that may cause undesired operation.
The deuce has been evaluated to meet the general RF exposure requirements.
The deuce can be used in mobile exposure condition the use distance is 20cm.. compliance with exposure requirements

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>