Mirabella genio I003975 Smart Wi-Fi LED Stick Light 6pc Instruction Manual
- June 6, 2024
- Mirabella genio
Table of Contents
I003975 Genio Smart Wi‐Fi LED Stick Light 6pc
TO ENSURE THE SAFE AND SATISFACTORY OPERATION OF THIS SET PLEASE READ THESE
INSTRUCTIONS CAREFULLY AND
RETAIN FOR FUTURE REFERENCE
FOR ANY QUESTIONS OR TROUBLESHOOTING PLEASE
VISITwww.mirabellagenio.net.au/faqs
We recommend that the set be tested prior to being set up in the desired
location
SAFETY INFORMATION:
- Remove set from the packaging before connecting to the power supply.
- Before using or re‐using the set, inspect carefully
- Use only with transformer supplied
- Do not connect set electrically to another set
- Do not use any set which has: – cut, damaged, or frayed wire insulation, cracks in lamp‐holders,loose connections, or exposed wires
- The LED bulb is not replaceable
Note: When connecting, please ensure the arrows are aligned with one another
Included in the Kit
|
| | 
|
---|---|---|---|---
Installation Screws| Power Adaptor| Installation clips| Extension cables|
Rubber end cap
Link and connect the stick light
It is recommended you connect the stick light according to the ABCD marking. A‐A, B‐B, C‐C D‐D, etc, and cover the end with the rubber end cap.
disable 5Ghz Wi‐Fi for your router.
Your phone must be connected to 2.4Ghz Wi‐Fi and not the 5GHz,
To verify your mobile phone is connected to a 2.4Ghz Wi‐Fi network, Navigate
to the Setting menu and click on Wi‐ fi. In this menu, you will see all
detectable networks in your area. Locate the SSID for your network, select a
Wi‐Fi SSID that doesn’t end with 5GHz.
Check you have a strong Wi‐Fi signal (at least two bars) in the location where
the smart device is installed.
If you don’t have at least two bars signal on your phone, then you may need to
reconsider the location or get a Wi‐Fi extender to boost the Wi‐Fi signal
strength.
If you have a dual-band router but you don’t see two Wi‐Fi names SSID’s, one
with 5G and one without 5G, you MUST log in to the router and manually disable
the 5Ghz Wi‐Fi signal if you’re having connection issues. Please contact
your internet provider on how to
Install the APP and register Account
For the best experience, download the “Mirabella Genio” APP to your smartphone
from the App Store or Google Play, the APP the icon will be displayed after
it’s installed successfully
EZ method – when the light is fast blinking (2 blinks per second)
Connect the stick lightly to the Wi‐Fi controller and power supply, then
switch on power at the wall, wait a few seconds, stick light will start to
rapidly blink (2 binks per second)
-
If it did not automatically start to blink fast when first powered on, press and hold the pairing button on the Wi‐Fi controller until the light starts to blink rapidly
-
Open Mirabella Genio APP, tap on +, add Manually then choose genio strip light from the list
-
Entre your 2.4Ghz Wi‐Fi name and password, (make sure the Wi‐Fi name doesn’t end with ‐5G)
Follow the APP instruction carefully to complete the network pairing process.
if the fast‐blinking method (EZ method, mentioned above) doesn’t work, please
try the slow blinking (AP method) below.
While the strip light is rapidly blinking, press and hold the pairing button
on the Wi‐Fi controller again and then wait for the light to start blinking
slowly (1 blink per every 2 seconds)
1. open up the Mirabella genio APP, tap on +, add Manually then choose
genio strip light from the list Entre your 2.4Ghz Wi‐Fi name and password,
(make sure the Wi‐Fi name doesn’t end with ‐5G) then reset the device first
screen tap on EZ mode in the top right-hand corner just below the battery
image, elect AP Mode (refer to the 1st and 2nd image below) Now Confirm
indicator slowly blinking (refer to image 3), hit Next, then Go to connect
and connect to Wi‐Fi named SmartLife_XXXX 
Note: If you fail to see the Wi‐Fi name beginning with the word
SmartLife_XXXX, then mean the device is not slowly blinking, please reset and
make it slowly blinking 
After being connected to SmartLife_XXXX, return back to
Mirabella Genio, APP will commence adding device
If you don’t have Wi‐Fi at home or cannot pair it but still want to use this
light, simply wait for the light stopped blinking, then you can short press
the pairing button to change different modes without the need for a genio APP.
Should the transformer, supply plug, or supply flexible cord get damaged,
do not attempt to repair.
TO BE REPAIRED BY AN AUTHORIZED PERSON ONLY
THIS IS AN AUSTRALIAN STANDARDS REQUIREMENT IN THE INTEREST OF YOUR SAFETY·
FAQ
Q. I have an internet/power outage and the device went offline and doesn’t
reconnect back online by itself?
A. Go to the strip light co’ settings page (pencil icon), look for “remove
device” Remove it and reset the device, and pair it again through the app.
Q. how do I control two or more lights at the same time?
A. Go to the device’ settings page (pencil icon), look for the “create group”
option, if you are using Telstra/Optus NBN and you still having issues with
pairing when using the AP method, please call our tech support line or check
our online FAQ pages on how to disable the 5Ghz WiFi on the router setting
www.mirabellagenio.com.au/faqs
Mirabella International Pty Ltd
1 Mirabella Drive Tullamarine VIC. 3043 Australia
t: 1800 636 528
e: customerservice@mirabella.com.au
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>