Powertech Industrial PR-91W 10 Outlet Smart Surge Protector Rack with Wi-Fi and USB User Guide
- June 6, 2024
- Powertech Industrial
Table of Contents
Brand: ProTek
Document: OUICK SETUP GUIDE SOURCE FILE
Product: 10 Outlet smart surge protector rack with Wi-Fi and USB
Model#: PR-91W
FEATURES
- Wi-Fi enabled to remotely control outlets by Elac ProTek app
- Set schedules and timers to automatically control outlets
- Alexa and Google Home compatible
- Total 10 outlets (9 in back, 1 in front)
- 4 USB-A ports (2 in back, 2 in front)
- 6480 joules of surge protection
- Electronic noise filtration 70dB
- 8ft power cord with 360 degree rotating plug
SYSTEM REQUIRMENTS
- Home Wi-Fi network 2.4Ghz
- Elac ProTek app (free download at [Elac app url])
PACKAGING CONTENTS
- Surge protector
- Quick Setup Guide
OVERVIEW
USING YOUR BLUETOOTH SMART SURGE PROTECTOR
-
Connect your mobile to Wi-Fi network
*Note: Must be same network you’re planning to connect PR-91W to -
Download Elac ProTek app from mobile app store [app logo here]
-
Plug your smart surge strip to electrical outlet
-
Open your app and follow the on-screen instruction to complete setup
UNDERSTANDING BUTTONS & LED INDICATORS
Item|
Behavior
---|---
Power Button| 1. Short press 0.5 -1 sec on/off all back outlets (G1 – G4)
2. Long press 10 second factory reset and in pairing/setup mode
Power Button LED| 1. Flashing: (a) Factory reset and in pairing/setup mode
2. Solid LED: Connected, relay ON
3. No LED: Connected, relay OFF
Reboot Button| 1. G1 outlet and LED always on
2. Short press reboot button 0.5 -1 sec, relay OFF 3 secs and back ON
LCD Dimmer Button| 1. Short press cycle through dimmer 10,35,70,100%
Voltage/Current Button| 1. Short press cycle through Voltage or Current
readings
G1 – G4 LED| 1. Light On: Relay on
2. Light off: Relay off
Protected / Clean Power| 1. Light On: Protected / Clean Power
2. Light off: Surge protection failed and must replace device
Ground OK| 1. Light On: Ground
2. Light Off: No Ground
Reverse Polarity| 1. Light off: Normal
2. Light On: Reverse polarity detected, check wiring
Unsafe Voltage| 1. Light off: Normal Voltage
2. Light On: Unsafe voltage detected
SPECIFICATIONS
- Surge suppression:
- Max. energy dissipation: 6480 joules
- Load rating: 15 amps
- Line voltage: 125V AC @ 60 Hz
- Over & Under voltage protection: Yes (auto shut off)
- Over voltage 135V auto shut off
- Under voltage 95V auto shut off
- USB output: 4 ports 5V/2.4A each pair
- Surge protection: To L-N only
- Clamping voltage: L-N = 500 volts
- UL-1449 certified
- FCC and IEC certified
SAFETY INFORMATION
-
RISK OF ELECTRIC SHOCK – Use only in dry locations and only indoors.
-
DO NOT plug into another relocatable power tap.
-
DO NOT “daisy chain” surge protectors.
-
DO NOT plug into 220V outlet or power source
-
DO NOT use with any aquarium equipment.
-
DO NOT use if correctly grounded outlets are not available
-
DO NOT install this device if there is not at least 30 feet (10 meters), or more of wire between the electrical outlet and electrical service panel.
-
This device features internal protection that will disconnect the surge protective component at the end of its useful life, but will maintain power to outlet – WHICH WILL
BE UNPROTECTED. If you don’t want your equipment at risk, follow the manufacturer’s instructions for replacing the device. -
DO NOT use in any circumstance that would affect the operation or reliability of life support equipment, any medical applications, or patient care.
FCC and IEC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Label Compliance Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
To assure continued FCC compliance:
- Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.
- This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
This radio transmitter (IC: 3653A-PR91W) has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Antenna Type: Dipole antenna Model Name: Q0211 Gain (Peak): 2.0dBi
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>