TRANSTYLE TW92-X True Wireless Earphone User Manual
- June 6, 2024
- TRANSTYLE
Table of Contents
User manaul for
Truly Wireless Earphones
In the Box
A Closer Lock
Charging
Connect the USB-C cable into the charging port to charge the case. The case’s indicator will flash momentarily to indicate a low battery.
Powering on
For the first use, place earbuds into the case then remove them from the case.
This will activate earbuds.
To turn on, place earbuds into the case then remove them from the case. To
turn off, place the earbuds into the case.
If the LEDs do not turn on when the earbuds are removed from the case, charge the case then try again. In the event that the earbuds do not pair together, perform the Manual Reset function.
Bluetooth Pairing
The NanoPods have automatic pairing technology. Once removed from the case,
they will automatically turn on and pair to each other within a few seconds.
After the earbuds have paired to each other, to connect the earbuds to your
smartphone, go to settings then select the Bluetooth page. Look under
‘available devices’ and connect to “NanoPods”.
Touch Button Functions
Decrease Volume: Press Once
Previous Selection: Press Twice
Voice Assistant: Press & Hold 2 Sec. Answer Call: Press Once
Decline Call: Press Twice
Hang Up Call: Press & Hold 2 Sec.| Increase Volume: Press Once
Next Selection: Press Twice
Pause/ Play: Press & Hold 2 Sec.
Answer Call: Press Once
Decline Call: Press Twice
Hang Up Call: Press & Hold 2 Sec
---|---
Manual Reset
Only do this function experience issues that are not solved by simply turning the earbuds on/off, or by placing them back into the case.
- Remove both earbuds from the case, the LEDs will flash blue 3 times.
- Now gently press and hold both touch buttons for 9 seconds, the LEDs will flash red/blue before resetting, then flash blue 5 times and the earbuds will reset.
- Now place both earbuds back into the case to activate the earbuds and take both earbuds out of the case and wait a few seconds for them to find each other and connect back together as a pair. The LEDs will flash blue then red/blue a few times. Once they are connected together only one earbud will flash red/blue. They are now ready to pair to your phone.
- Now simply re-connect to the earbuds on your phone, you should see them in your phone’s pairing list as ‘NanoPods’.
Notes
To use Ski or Google Assistant, you must have a phone that is compatible with
one of those two voice assistants (iOS or Android, respectively).
You must be within Bluetooth0 range to use Ski or Google Assistant via your
Wireless Earbuds.
Your Wireless Earbuds will not work with Siri or Google Assistant if the
assistant is not first enabled within the settings on the phone. For more
information, see your phone’s user manual.
To use Sid or Google Assistant, you must have a phone that is compatible with
one of those two voice assistants (iOS or Android. respectively).
You must be within Bluetooth® range to use Sid or Google Assistant vial your
Wireless Earbuds. Your Wireless Earbuds will not work with Sid or Google
Assistant if the assistant is not first enabled within the settings on the
phone. For more information, see your phone’s user manual.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help. The
device has been evaluated to meet general RF exposure requirements. The device
can be used in portable exposure conditions without restriction
FCC ID: 2AVTV-TW92
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>