Transtyle Technology MZX5100 AL Nanobuds Pro True Wireless Earbuds User Guide
- June 6, 2024
- Transtyle Technology
Table of Contents
MZX5100
AL Nanobuds Pro
Quick Start Guide
IN the Box
Large Medium Smal
Different Size Ear Tips
Medium Memory Foam Tips
|
---|---
Nanobuds Pro and Charging Case| USI3-C Cable
FCC 10:2ALN9-TW91
A Closer Look
Charging
Place the earbuds into the case to charge:
Charging (indicator breathing red every 35)
Fully charged (indicator breathing blue every 3S)
The LEDs turn off after about SOS to conserve power
The LED indicator will flash when charging:
Connect the USB-C cable into the charging port to charge the case.
The case’s indicator will flash momentarily to indicate a low battery.
Powering On
For the first use, place earbuds into the case then remove them from the case.
This will activate earbuds.
To turn on, place earbuds into the case then remove them from the case.
To turn off, place the earbuds into the case.
If the LEDs do not turn on when the earbuds are removed from the case, charge the case then try again. In the event that the earbuds do not pair together, perform the Manual Reset function.
Bluetooth Pairing
The AL Nanobuds PRO has automatic pairing technology. Once removed from
the case, they will automatically turn on and pair to each other within a
few seconds.
After the earbuds have paired to each other, to connect the earbuds to your
smartphone, go to settings then select the Bluetooth page. Look under
‘available devices’ and connect to “AL Nanobuds PRO”.
Touch Button Functions
Left Earbud :
Decrease Volume: Press Once
Previous Selection: Press Twice
Voice Assistant Press & Hold 2 Sec.
Answer Cal: Press Once
Define Call: Press Twice
Hang Up Call: Press & Hold 2 Sec.| Right Earbud:
Increase Volume: Press Once
Next Selection: Press Twice
Pause/ Play: Press & Hold 2 Sec.
Answer Cal: Press Once
Define Cal: Press Twice
Hang Up Call: Press & Hold 2 Sec.
---|---
Manual reset
Soft Reset
To perform a Soft reset simply drop the earbuds back in the case and hold the
touch button, the LED will go off, let go after 2S and the earbud will be
reset without losing any pairing information. In the unlikely event that you
need to fully reset the earbuds and dear their pairing information you can do
a Hard reset as follows: Hard Reset
- Forget the earphones in your phone (important).
- Take ONE earbud out of the case. If the LED is flashing purple wait for it to go red/blue/red/blue. Now Press and Hold the earbud touch button for 12S. The LED wd change to Red for 55 and the earbud will reset
- Put it back in the case and do the same operation for the other one.
- Finally, take them both out together, the earbuds will flash purple while they look for each other. Then when they pair together the Primary will go Red/Blue/Red/Blue (the Secondary LED will turn off).
- The earphones are now ready to pair to your phone.
- Reconnect the earbuds to your phone. You should see them in your phone’s pairing list as AL Nanobuds PRO.
Notes
To use Sid or Google Assistant, you must have a phone that is compatible with one of those two voice assistants (i0S or Android, respectively). You must be within Bluetooth,,’ range to use Siri or Google Assistant via your Wireless Earbuds. Your Wireless Earbuds will not work with Sid or Google Assistant if the assistant is not first enabled within the settings on the phone. For more information, see your phone’s user manual.
For additional user materials and warranty information, please visit alteclansing.com
FIRST
Changes or r indications not expressly approved by the party responsible or
compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1)this device may not cause harmful interference,
and (2)this device must accept any interference received, including
interference that may cause undesired operation. This equipment has been
tested and found to comply with the knits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used In accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that Interference wl does not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>