KONNWei KW710 6V/12V/24V Car Battery Tester User Manual

June 6, 2024
KONNWEI

6V/12V/24V Car Battery Tester KW710

battery tester

User’s Manual

KW710 Battery Tester can test all 6V, 12V, 24V automotive cranking lead acid battery, including ordinary lead acid battery, AGM flat plate battery, AGM spiral battery, and Gel battery, etc. it adopts the state-of-the -art conductance testing technology in the word to easily, quickly and accurately measure the actual cold cranking amps capability of the vehicle starting battery, healthy state of the battery itself, and common fault of the vehicle starting system and charging system, which can help maintenance personnel to find the find the problem quickly and accurately, thus to achieve quick vehicle repair.

Other Feature include:

  • The battery detection range is from 100 to 2000 CCA;
  • Bad cell detection function;
  • Polarity misconnection protection;
  • Measure deeply discharged batteries;
  • Various battery specifications testing (CCA, JIS, EN, DIN, SAE, IEC);
  • Provide multiple language interfaces for selection: Chinese, English, German, French ,Japanese,Korean, Dutch, Russian, Spanish,Italian, Portuguese, Polish, Persian.

Feature

Noted : If test on the vehicle, please make sure to disconnect all loads, and don’t out the key in the ignition position and must close the door . Connect the red clip to the positive (+) terminal of the battery and the black clip to the negative (-) terminal. After connecting, shake the clip back and forth to make the connection firm. Before testing the battery, two clips are required to connect the terminals firmly. The best test location is the connection port of the battery. If the battery cannot be connected from the wiring port, you can try to test on the jumper port, but the measured data may be lower than the actual value.

Menu Selection

Motorcycle menu
After entering motorcycle menu , select “ BatteryRating “ The screen will display the test result ,Press the up and down keys to switch
between SOH and SOC
SOC:state of charge
SOH :state of health
Battery test result includes 5 types as following: ( Good Battery / Good, Recharge / Replace / Bad cell, Replace / Charge, Retest )

Set Battery Rating

Car menu

After entering car menu , Tester will display the following contents in a sequence, select accordingly:“ Battery In-vehicle or Out-of-Vehicle”

Press UP/DOWN key to select the battery location, in vehicle or out of vehicle, then press ENTER key to confirm.

For Example ,Select “ Battery Test out-of- vehicle” , Then show battery type as shown : Regular Flooded,AGM Flat Plate,AGM Spiral,GEL,EFB.

Then select battery standard and input battery CCA value to get the test result .

CCA

Select Type

Truck menu
After entering Truck menu , Tester will display the following contents in a sequence, select accordingly:
“ Battery In-vehicle or Out-of-Vehicle”
Press UP/DOWN key to select the battery location, in vehicle or out of vehicle, then press ENTER key to confirm.
For Example ,Select “ Battery Test out-of- vehicle” , Then show battery type as shown : Regular Flooded,AGM Flat Plate,AGM Spiral,GEL,EFB.
Then select battery standard and input battery CCA value to get the test result .

Battery Location

Waveform menu
Press WAVEFORM FUNCTION button, The screen will display the interface as shown below:
CUR: Current Voltage
MAX: Maximum Voltage during Ignition
MIN: Minimum Voltage during Ignition; The waveform will stay in static until there’s changes in the voltage changes detected

Waveform menu

Battery Test

1. Battery location: select inside or outside the car. During the in- vehicle test, the tester will further test the starting and charging system.

  1. Important note: The performance of the starting and charging system depends on the health of the battery. It is necessary to check the starting and charging system after confirming that the battery is in good performance and fully charged.

  2. Menu: select Car, Motorcycle, Truck

  3. Battery type: select ordinary lead-acid battery, ordinary AGM battery, winding type AGM battery or gel battery.

  4. Battery standard: Please check your own battery standard. The battery

usually uses one or more standard systems.
KW710 battery tester each battery according to the selected system and rating.
Use UP/DOWN key to select according to the actual system standard and rating marked on the battery.

Description

  1. Battery rating: up/down button to select rating, press and hold the up/down button to speed up the scrolling speed.

  2. Press the Enter key to start the test. After a few seconds, the tester
    displays the result of the battery test and the measured voltage.

  3. The tester can also display the type and specifications of the battery tested.

Set Battery Rating

Tester Result

Attention: If “Replace” resulted from IN-VEHICLE mode, it might be the reason that vehicle cable is not well connected with the battery, Ensure to cut off the cable and retest the battery under OUT-OF-VEHICLE before making a decision to replace battery.

Cranking Test
Important note: Before starting the test, check the drive belt of the generator.
If the belt is shiny or worn, or lacks proper tightness, the machine will not reach the speed level required for detection.

  1. When the battery test in the car is completed, the battery test results and prompts will be displayed alternately. Press Enter to test and start the system.
  2. Press the enter key to do cranking system test.
  3.  The tester will prompt to start the engine.
  4. The KW710 tester will displays the test results : the max cranking voltage, the min the cranking voltage, and the cranking time in milliseconds, cranking lower / higher etc.

Cranking Test
TIME: 7554ms
MAX:9.84V
MIN:8.47V
CRANKING LOW

Cranking Test Result

Charging Test
Once the cranking system test is completed, the screen will alternately display the cranking system test results and prompts. Press the Enter key to test the charging system. Press the Enter key to perform charging test.
Follow the instructions on the screen: Increase RPM to 2500 r/min and keep it 5 seconds, Press ENTER to continue

  1. Increase the throttle when closing the load
  2. The engine speed is detected and the engine is idling
  3. Test the generator when the load is off and idling
  4. Turn on the headlights and blower when the engine is idling
  5. Test the generator when the load is clocked in and idling
  6. Increase the throttle when opening the load After the process is over, the tester displays the test results of the charging system.

In - Vehicle

Charging Test Result

High output

  • Discharge Voltage: When the ignition OFF, engine OFF (Over 20 Minutes), the Discharge Voltage should be around 12V. If the discharge voltage is lower than 11V, it will be hard to turn the ignition ON. If the discharge voltage continuously stay under 11V, ii means the battery is aging and replacement is needed.
  • Starting Voltage: During ignition, the voltage will drop to a certain point, at this minimum point is Starting Voltage (Around 7.5- 9.5V). If the Starting Voltage continuously stay under 7.5, it means battery capacity is low and needs to be replaced
  • Charging Voltage: When the ignition ON, engine ON. The alternator will continuously charge the car battery, normally is around 14V

Battery Status

Print Menu & Update
This function allows you to update and print the tool software through a computer .
To update and print your tool, you need the following items

  1. KW710 tool;
  2. A PC or laptop with USB ports;
  3. USB cable

Step :

  1. Downloading the applications from our website www.konnwei.com

  2. Run btlink.exe in your computer( Windows 7 /8/10 /xp)
    Noted : Mac OS and linux does not compatible

  3. Press and hold any button until the USB cable is connected with computer and release it after the tool display a message “Update Mode”

  4. Open the btlink software, click “Check update” button, will download the upgrade file from internet then update to tester tool

  5. Wait for the update process finished, the scanner will be ready to go! we will update to latest version before shipping out, normally there is no need to update for a long while.

  6. Restart tester tool finish the whole update . Notice: Please turn off anti-virus software when installing the update tool, otherwise it will not be able to install the driver properly.

Service

Service Procedures
If you have any questions, please contact your local store, distributor or visit our website at www.konnwei.com
If it becomes necessary to return the tool for repair, contact your local distributor for more information.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals