Rinnai S26i Continuous Flow Solar Hot Water Booster User Manual
- June 6, 2024
- Rinnai
Table of Contents
Models:
S26i (REU-VRM2632FFUG) (70)
S28i (REU-VCM2837FF) (70)
S32 (REU-VRM3237WG) (70)
Continuous Flow Solar Hot Water Booster
Operation & Installation Manual
Congratulations on the purchase of your Rinnai Continuous Flow Solar Hot Water
Booster. We trust you will have many years of comfort and enjoyment from your
appliance.
BEFORE USING THIS APPLIANCE
Before proceeding with the operation or installation read this manual
thoroughly and gain a full understanding of the appliance, to ensure safe and
correct use.
This appliance must be installed in accordance with:
- Manufacturer’s Installation Instructions
- Current AS/NZS 3000, AS/NZS 3500 & AS/NZS 5601
- Plumbing Code of Australia (PCA)
- Local Regulations and Municipal Building Codes including local OH&S requirements
This appliance must be installed, maintained, and removed by an Authorised
Person.
For the continued safety of this appliance, it must be installed and
maintained in accordance with the manufacturer’s instructions.
WARNINGS & IMPORTANT INFORMATION
REGULATORY INFORMATION
Your Rinnai Continuous Flow Solar water heater has been certified by the
Australian Gas Association.
The A.G.A. Certification Number is shown on the data plate.
This Appliance must be installed correctly by an authorized person. The
installation of gas, water, and electricity must conform to local regulations.
The installation must also comply with the instructions supplied by Rinnai.
All dimensions referred to in these instructions are in millimeters, unless
otherwise specified.
Please keep this instruction booklet in a safe place for future reference.
Notice to Victorian Consumers
This appliance must be installed by a person licensed with the Plumbing
Industry Commission.
Only a licensed person will have insurance protecting their workmanship.
So make sure you use a licensed person to install this appliance and ask for
your Compliance Certificate. For further information contact the Plumbing
Industry Commission on 1300 815 127.
**WARNING ABOUT HOT WATER
**
This appliance MUST only be installed in accordance with the acceptable
plumbing configurations specified in these instructions. Failure to do so may
result in conditions where delivery temperature control is inadequate.
This appliance may deliver water at high temperature. Refer to the Plumbing
Code of Australia (PCA), local requirements and installation instructions to
determine if additional delivery temperature control is required.
Hot water can cause scalding. Those most at risk are children and disabled,
elderly and infirm persons. (65°C water can severely burn a child in half a
second).
Rinnai has water heater models which limit the delivery temperature to 50°C
which significantly reduces the scald hazard. Temperature limiting devices may
also be able to be fitted. Contact Rinnai for further information.
Always test the water temperature before use, such as when filling a bath or
basin or entering a shower, to ensure it is suitable for the application and
will not cause scald injury.
Always supervise children whenever they are in the bathroom or near other
sources of hot water. Ensure any hot water taps are closed firmly after use.
APPLICATIONS
Rinnai continuous flow Solar models S26i, S28i and S32 are suitable ONLY for
installation as gas boosters in Rinnai solar hot water systems (see picture
right).
These models are not suitable for use as ‘stand-alone’ appliances for the
purposes of supplying hot water.
For nonsolar hot water applications, Rinnai has a dedicated range of
continuous flow water heaters available.
Contact Rinnai for more details.
Operational Safety Information
Always check water temperature carefully before use.
Refer to the “WARNING ABOUT HOT WATER” on page 4 for important safety
information.
DO NOT touch the unit cover or the flue outlet.
DO NOT insert objects into the flue outlet.
DO NOT spray water directly into the flue outlet.
Keep, trees, shrubs, etc. well clear of the flue outlet.
On colder days steam may discharge from the flue outlet. This condition is
normal for high-efficiency appliances and does not indicate a fault.
At low water flows, the hot water unit may extinguish without warning.
Opening the tap further will restart the heating appliance.
DO NOT Spray aerosols in the vicinity of this appliance while it is in
operation.
DO NOT use or store flammable materials in or near this appliance.
DO NOT place articles on or against this appliance.
DO NOT modify this appliance.
DO NOT store pool chemicals near this appliance.
If freezing conditions are expected, ensure the electric power supply to the
gas booster remains ‘ON!’. This will assure the automatic Anti-frost
protection can operate when required.
However, if freezing conditions are expected and power will not be available,
then turn off water and gas, and drain all water from the appliance.
Features & Benefits
Congratulations on purchasing the latest technology Rinnai continuous flow water heating system.
- The Rinnai solar range of continuous flow water heaters NEVER RUN OUT of hot water even during times of limited solar radiation and/or high hot water demand. Whilst the electricity, water and gas supplies are connected, hot water is available whenever hot water taps are open.
- The Rinnai solar range of continuous flow water heaters are fan-assisted appliances. This makes them COMPACT saving both floor and wall space.
- GNITION IS ELECTRONIC, so there is no pilot light. When the hot water tap is off, no gas is used.
- Operating NOISE LEVEL IS VERY LOW.
- The “Smartstart ® ” system (when fitted) can pre-heat the water in the pipework between the continuous flow unit and hot water outlets. This results in water savings and reduces waiting time for heated water at the outlets.
Troubleshooting & Warranty Conditions
These are outlined in detail in the following Rinnai publications:
- Operation / Installation Manual Rinnai Split Solar Hot Water Systems
- Operation / Installation Manual Rinnai Close Coupled Solar Hot Water Systems
- Operation / Installation Manual Rinnai Evacuated Tube Split Solar Hot Water Systems
These publications are supplied separately with your solar hot water system and should have been handed to the end-user by the system Installer. If a copy of either of these publications is required please contact Rinnai.
INSTALLATION, COMMISSIONING
Rinnai continuous flow Solar models S26i, S28i, and S32 are specifically designed for installation as gas boosters in Rinnai Solar Hot Water Systems. They are not suitable for use in any other applications.
The Installation, Commissioning, Maintenance, and Service information for Rinnai Solar hot water systems and components including the gas booster is detailed in the following Rinnai publications:
- Operation / Installation Manual Rinnai Split Solar Hot Water Systems
- Operation / Installation Manual Rinnai Close Coupled Solar Hot Water Systems
- Operation / Installation Manual Rinnai Evacuated Tube Split Solar Hot Water Systems
These publications are supplied separately with your solar hot water system
and should have been handed to the end-user by the system Installer. If a copy
of either of these publications is required please contact Rinnai.
Solar models S26i, S28i and S32 are factory pre-set and sealed to a delivery
temperature of 70°C to meet regulator requirements. This setting cannot be
altered. Local regulations and/or the requirements of AS/NZS 3500 must be
considered regarding the temperature limitations to areas primarily used for
personal hygiene. Temperature limiting devices may be required. Refer to the
above-mentioned Rinnai publications for more information.
A pouch behind the front cover of continuous flow models contains gas pressure
setting and diagnostics information and a wiring diagram of these appliances.
This information must be read in conjunction with the relevant solar system
Operation / Installation manual. This gas pressure setting and diagnostics
information is usually not required during installation.
Installation, Commissioning, Maintenance, and Service by an Authorised person
only. DO NOT attempt to install any solar hot water system components
(including the gas booster) without first studying the relevant Rinnai
publications.
S28i (REU-VCM2837FF) (70) has an integrated control module. This control
module includes UP / DOWN buttons, ON / OFF buttons, Priority Button and LED
Digital Display. Solar models are pre-set and sealed to a delivery temperature
of 70°C. The water temperature cannot be adjusted using UP / DOWN Buttons.
OTHER ACCESSORIES
Use of a Recess Box permits the recessed installation of a Rinnai S32 gas
booster into a wall cavity while saving precious space they are also suitable
for painting. Available in either plastic (Smart Box) or metal.
Conceal the pipes and valves of the Rinnai S32 gas booster with easily
attached Pipe Covers. These pipe covers may also be joined to one another to
conceal longer pipework runs.
Protect the Rinnai S32 gas booster from theft and damage with a Security Cage.
Secure the Rinnai S26i, S28i, and S32 gas booster from theft with a custom-
designed Security Bracket.
Pre-heat your hot water to reduce hot water delivery times and water wastage
with a Smartstart pre-heat system.
Contact Rinnai for more information about our accessory range and model
suitability, or visit: www.rinnai.com.au.
NOTES
Rinnai Australia Pty Ltd
ABN 74 005 138 769 | AU45204
100 Atlantic Drive, Keysborough, Victoria 3173
P.O. Box 460, Braeside, Victoria 3195
Tel: (03) 9271 6625
Fax: (03) 9271 6622
National Help Line
Tel: 1300 555 545 Fax: 1300 555 655
Monday to Friday, 8.00 am to 5.00 pm EST.
After Hours Hot Water Service Line
Tel: 1800 000 340
*Cost of a local call is higher than a mobile or public phone.
For further information visit www.rinnai.com.au or
email enquiry@rinnai.com.au
Rinnai has a Service and Spare Parts network with personnel who are fully
trained and equipped to give the best service on your Rinnai appliance. If
your appliance requires service, please call our National Help Line. Rinnai
recommends that this appliance be
serviced every 3 years.
With our policy of continuous improvement, we reserve the right to change, or
discontinue at any time, specifications or designs without notice.
HW_CF_SOLAR OIM Issue 3 Workshop – October 2021
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>