ECHELON ECHTES-156 Touch Screen User Manual
- June 6, 2024
- Echelon
Table of Contents
ECHELON ECHTES-156 Touch Screen User Manual
About This Document
No part of this publication may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language or computer
language, in any form or by any means, including, but not limited to,
electronic, magnetic, optical, chemical, manual, or otherwise without prior
written permission of Echelon Fitness Multimedia LLC.
The information in this document is subject to change without notice. Echelon
makes no representations or warranties with respect to the contents herein,
and specifically disclaims any implied warranties of merchantability or
fitness for a particular purpose. Echelon reserves the right to revise this
publication and to make changes from time to time in the content hereof
without obligation of Echelon to notify any person of such revisions or
changes. Windows is a registered trademark of Microsoft, Inc. Other brand or
product names are trademarks of their respective holders.
Compliance Information For FCC (USA)
Caution: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help important announcement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
RF Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance of 15cm the radiator
your body. This device and its antenna(s) must not be co-located or operation
in conjunction with any other antenna or transmitter.
Usage Notice
- Warning – To prevent the risk of fire or shock hazards, and do not expose the product to moisture.
- Warning – Please do not open or disassemble the product as this may cause electric shock.
- Warning – Power cord shall be connected to a socket-outlet with earthing connection.
- Warning – The cable cover cannot be removed under normal use conditions.
- Warning – Stability Hazard. The touch monitor may fall, causing serious personal injury or death. To prevent injury, this touch monitor must be securely attached to the wall in accordance with the installation instructions.
Precautions
Please follow all warnings, precautions and maintenance as recommended in this
user’s manual to maximize the life of your unit.
Do:
- Turn off the product before cleaning.
- Use a soft cloth moistened with mild detergent to clean the product housing.
- Use only the qualified power adapter that comes with your device.
- Disconnect the power plug from AC outlet if the product is not going to be used for an extended period of time.
Don’t:
- Do not use abrasive cleaners, waxes or solvents for your cleaning.
- Do not operate the product under the following conditions:
- Extremely hot, cold or humid environment.
- Areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
Caution
Risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.
Product Introduction
Overview
The ECHTES-156 is a thinner 15.6″ touch computer that offers a unique screw
less design with expandability and flexibility, making expansion and accessory
installation much easier. The versatility of ECHTES-156 is an exceptional
choice for applications in all fitness sectors.
Feature
- Support Rock chip RK3288 processor.
- Support Wi-Fi 802.11ac 2T2R & BT5.0 1T1R.
- Support 5MP FF camera.
- Support Screen rotation.
- Unique screw less design for better user experience.
- Patented I/O design for better wiring management while implementation
Specifications
System
CPU| Rock chip RK3288, Quad-core Cortex-A17 up to 1.8GHz
GPU| Mail-T760 MP4
Memory| 4GB dual channel LPDDR3
Storage| 16GB eMMC
Input Power| DC in 12V/4A 2PIN
Display| 2lane eDP, resolution up to 1920x1080P60
Touch| 15.6inch P-Cap touch sensor , supports 10 fingers touch function.
Audio| 2 x speaker (5W x 2)
G-sensor| 3-axis
Network
| Gigabit Ethernet
Wi-Fi 802.11a/b/g/n/ac, 2T2R
| Bluetooth 5.0 (Support BLE) 1T1R
---|---
External IO Ports
| 1 x LAN (Support 10/100/1000Mbps) 1 x TF slot (Support SDHC 2.0)
1 x Recovery key
1 x HDMI (Support 1080P@60Hz)
2 x USB2.0 Type-A (1 x HOST, 1 x OTG)
2 x 3.5mm earphone jack (Only one can be used at the same time)
1 x 12V DC In
1 x 12V DC out (12V/1A)
1 x Power button, 1 x vol -, 1 x vol +
OS Version| Android 9.0
Operation Temp| 0°C~40°C
Storage Temp.| -20°C to 60°C
Operation Humidity| 20~80%, Non-Condensing
Storage Humidity| 10~90%, Non-Condensing
LCD Touch Panel
Size| 15.6” TFT LCD
Brightness
(non-touch screen)
| Typical 250 cd/m2; min. 200 cd/m2
Brightness (P-CAP)| Typical 225 cd/m2; min. 180 cd/m2
Number of Pixels| 1920 (H) × 1080 (V)/ 60Hz
Environment
Certificate
| CE、FCC、IC、LVD、UL、UKCA、RF、NOM、RCM、ANATEL
Mounting| VESA 100 mm x 100 mm
Dimension (W x H x D)| 375.40 mm x 271.70 mm x 45.92 mm
Net Weight| 1.8 Kg
Gross Weight| 2.85 Kg
Block Diagram
Interface Connectors
12V DC in | Pin # | Signal Name | Pin # | Signal Name |
---|---|---|---|---|
1 | 12V | 2 | GND |
12V DC out | Pin # | Signal Name | Pin # | Signal Name |
---|---|---|---|---|
1 | 12V | 2 | GND |
RJ45 for LAN | Pin # | Signal Name | Pin # | Signal Name |
---|
| 1| TP1+| 2| TP1-
3| TP2+| 4| TP3-
5| TP3+| 6| TP2-
7| TP4+| 8| TP4-
USB2.0
| Pin #| Signal Name| Pin #| Signal Name
---|---|---|---|---
1| USB5V| 2| D-
3| D+| 4| GND
Pin # | Signal Name | Pin # | Signal Name |
---|---|---|---|
1 | TMDS Data2+ | 2 | TMDS Data2 Shield |
3 | TMDS Data2- | 4 | TMDS Data1+ |
5 | TMDS Data1 Shield | 6 | TMDS Data1- |
7 | TMDS Data0+ | 8 | TMDS Data0 Shield |
9 | TMDS Data0- | 10 | TMDS Clock+ |
11 | TMDS Clock Shield | 12 | TMDS Clock- |
13 | CEC |
(N.C on device)
| 14| Reserved
(N.C. on device)
15| SCL| 16| SDA
17| DDC/CEC Ground| 18| +5V Power
19| Hot Plug Detect| |
Pin # | Signal Name | Pin # | Signal Name |
---|---|---|---|
1 | DAT2 | 2 | DAT3 |
3 | CMD | 4 | VCC |
5 | CLK | 6 | GND |
7 | DAT0 | 8 | DAT1 |
9 | CD | ||
Line Out | Pin # | Signal Name | Pin # |
--- | --- | --- | --- |
1 | MIC IN | 2 | Left |
3 | Right | 4 | GND |
5 | NC | 6 | DET |
Package Overview
Warning!
This product is intended to be supplied by a UL Listed Power Adapter, rated
12Vdc, 4A minimum. (complied with LPS or PS2) Tma = 40 degree C minimum, and
the altitude of operation = 2000m minimum. If it needs further assistance with
purchasing the power source, please contact to Echelon for further
information.
Product Installation
About VESA Mount
The ECHTES-156 conform to the “VESA Flat Display Mounting Interface Standard”
which defines a physical mounting interface for touch computer, and
corresponding with the standards of touch computer mounting devices, such as
wall-mounted. The VESA mount is located on the back of this unit.
The equipment is only for wall mounting for horizontal (output connector
facing down) and vertical mounting orientations (output connector facing left
or right) when EUT without base.
Warning!
Please select the Echelon original screws!
The distance between the back cover surface and the bottom of the screw hole
is 8 mm. Please use four M4 / 8 mm screws diameter with proper length to mount
your monitor.
Note: The mounting stand must be able to support at least 3.97 lbs (1.8
Kg).
Power On / Off
Function | Description |
---|---|
Power on | Press the power button |
Power off | Press the power button 2 sec and click power off. |
Vol- | Press the vol- button to turn the volume down. |
Vol+ | Press the vol+ button to turn the volume up. |
Dimension
Front View
Side View
Rear View
Bottom View
Documents / Resources
|
ECHELON ECHTES-156 Touch
Screen
[pdf] User Manual
ECHTES156, 2AWD4-ECHTES156, 2AWD4ECHTES156, ECHTES-156, Touch Screen
---|---