AOC GH401 Wireless Gaming Headset User Guide
- June 6, 2024
- AOC
Table of Contents
GH401 Gaming Headset
Quick Start Guide
WHAT’S IN THE BOX
PRODUCT OVERVIEW
MICROPHONE MUTE/UNMUTE
CHARGING
- If your headset is disconnected from your gaming device and no operation is performed within five minutes. the headset will automatically power off.
- When the 3.5mm audio cable is connected, the headset will automatically power off and enter the wired mode.
- Low battery warning: when the battery level reaches 2%, the headset will provide voice prompt “Battery Low” for charging warning every 5 minutes, and automatically power off in 15 minutes.
Note: It is recommended to fully charge your headset before the first use.
POWER ON/OFF
CONNECT BY 2.4GHZ WIRELESS
- Connect the USB Wireless Dongle to your gaming device.
- Press the Power Button on the headset for 3 seconds to power on the headset.
- When the Status LED in the USB Wireless Dongle is lighting in BLUE constantly and the POWER LED on the headset is lighting in BLUE every 10 seconds, the headset is successfully connected by the 2.4GHz wireless technology.
Note: Before using the headset for the first time, you need to set the headset (AOC GH401) es the deleult INPUT and OUTPUT audio device foi your gaming
CONNECT BY 3.5MM WIRED MODE
CONNECT/DISCONNECT MICROPHONE
- Connect: hold the end of the microphone (plug side), adjust the angle to align the indicator to match the slot inside the jack connector and plug in until reaching the bottom, rotate the plug 90-degree anti-clockwise to lock the microphone.
- Disconnect: hold the end of the microphone (plug side), rotate the plug 90-degree clockwise to unlock the microphone, and pull out the microphone from the jack connector.
QUESTIONS OR HELP NEEDED
Dear Customer,
Thank you for purchasing the AOC IT Accessory product.
Do you have questions or need help on setup? Visit www.aoc.com, select your
region and go to the support section. Find user manuals, software downloads or
contact our customer service center.
FCC Warning Statement
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment
ISED Canada Statement:
This device contains licence-exempt tasmittre(s)/receiver(s)/ that comply with
Innovation Science and Economic Development Canada ‘s licence-exempt RSS(s).
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Radiation Exposure: This equipment complies with Canada radiation
exposure limits set forth for an uncontrolled environment.
RF Exposure Statement: To maintain compliance with IC’s RF Exposure
guidelincs, This equipment should be installed and operated with minimum
distance of 5mm the radiator your body. This device and its antenna(s) must
not be co-located or operation in conjunction with any other antenna or
transmitter.
Information in this document is subject to change without notice.
©2021 AOC All rights reserved.
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>