SONOFF S-MATE Switch Mate User Manual

June 6, 2024
SonOFF

SONOFF S-MATE Switch Mate User Manual
SONOFF S-MATE Switch Mate

Product Introduction

Product Introduction
Product Introduction

The device weight is less than 1 kg. The installation height of less than 2 m is recommended.

Features

This is a module with “eWelink Remote” that can connect with the ordinary rocker or pulse switch. The smart device will be cut off and out of control when the ordinary switch is off. S- MATE is specially used to deal with this issue. After connecting with the rocker or pulse switch, smart device like MINIR3 can be controlled through “eWeLink Remote” of the module.

Operating Instruction

  1. Pull out the battery insulation sheet.
    Operating Instruction
    Operating Instruction
    Operating Instruction

  2. Power off
    Operating Instruction
    Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection or contact the terminal connector after plugging In!

  3. Wiring instruction
    The wiring instruction of connecting the S-MATE with one MINIR3:

The wiring instruction of connecting the S- MATE with three MINIR3:
Wiring instruction

The dip switch is factory set to the right. Please toggle the dip switch to the left if connection a pulse switch to the device.

Make sure the neutral wire and live wire connection is correct.

The “Study Binding” of MINIR3 and the external switch connected to the S-MATE.

The switch connected to S-MATE can be used as a “eWeLink Remote” controller. Access the MINIR3 main interface of eWeLink APP and operate it according to the operation guide (as shown below).
Connecting Instructions

The «Delete Binding” of MINIR3 and the external switch connected to the S-MATE.

Select the remote control that you want to clear in the learned remote control list in the eWeLink APP, then go to delete.

Specifications

Model 5-MATE
Input 100-240V – 50/60Hz 16A Max
Output 100.240V – 50/60Hz 16A Max
Power supply 3V button cell x 1
Battery model CR2032
“eWeLink remote” Transmission Distance Up to 50M
Working temperature -10°C-40t
Shell material PC VO
Dimension 51×44.5x24mm

Replace Battery

Replace Battery

Please turn off the electricity before replacing the battery of device.

FCC Warning

Changes or modifications not expressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type 5-MATE is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address:
https://sonoff.tech/usermanuals

Shenzhen Sonoff Technologies Co., Ltd.

1001, BLDG8, Lianhua Industrial Park, shenzhen, GD, China
ZIP code: 518000
Website: sonoff.tech
MADE IN CHINA

Icon

Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals