GardenJoy FH-GT120 Cordless Grass Trimmer Lithium-Ion Battery Pack Owner’s Manual
- June 6, 2024
- GardenJoy
Table of Contents
OWNER’S MANUAL
CORDLESS GRASS TRIMMER LITHIUM-ION BATTERY PACK
Model FH -GT120
BATTERY MUST BE CHARGED BEFORE FIRST USE. TWO TO THREE INITIAL CHARGING/ DISCHARGING CYCLES MAY BE REQUIRED TO ACHIEVE MAXIMUM RUN TIME/CAPACITY.
Your grass trimmer has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the owner’s manual before using this product.
Thank you for your purchase.
SAVE THIS MANUAL FOR FUTURE REFERENCE
IMPORTANT SAFETY WARNINGS
TO REDUCE RISK OF INJURY: Before any use, be sure everyone using this
tool reads and understands all safety instructions and other information
contained in this manual.
CAUTION: Wear appropriate personal hearing protection during use. Under
some conditions and duration of use, noise from this product may contribute to
hearing loss. Save these instructions and review them frequently prior to use
and in instructing others.
WARNING: When using electric gardening appliances, basic safety
precautions should always be followed to reduce the risk of fire, electric
shock, and personal injury, including the following:
READ ALL INSTRUCTIONS
GENERAL SAFETY
KEEP CHILDREN AWAY – Al visitors, children, and pets should stay at a
safe distance from the work area.
DRESS PROPERLY – Don’t wear loose clothing or jewelry. Wear protective
hair covering to contain long hair. They can be caught in moving parts. Use of
rubber gloves and substantial footwear is recommended when working outdoors.
Always wear long pants when operating this grass trimmer.
USE SAFETY DIASSES- Wear safety glasses with side shields or goggles when
operating this product. Use a face or dust mask if the environment is dusty.
USE RIGHT APPUANCE – Do not use an appliance for any job except that for
which it is intended.
REMOVE THE BATTERY FROM THE grass trimmer when not in use or when
servicing or cleaning. Do not leave unattended.
CHECK DAMAGED PARTS – Before further use of the trimmer, a guard or other
part that is damaged should be carefully checked to determine that it will
operate properly and perform its intended function. A guard or other part that
is damaged should be properly repaired or replaced.
LIGHTING – Only operate trimmer in daylight or good artificial light.
DON’T OVERREACH – Keep proper footing and balance at all times.
WARNING: Do not use the grass trimmer with any type of accessory or
attachment. Such usage might be hazardous.
AVOID DANGEROUS ENVIRONMENTS – Don’t use a trimmer in rain. damp or wet
locations. Do not operate trimmer in gaseous or explosive atmospheres. Motors
in these tools normally spark, and the sparks might ignite fumes.
AVOID UNINTENTIONAL STARTING – Don’t carry the string trimmer with your
finger on the switch. Be sure the switch trigger is in the locked or of
position before inserting the battery pack.
DANGER: Risk of cut Keep hands away from the blade. Keep both hands on
handles when power is on.
DANGER: Don’t use the tool if switch trigger does not tum on or oft
DANGER: Do not dispose of the batteries in a fire. The cell may explode.
Check with local codes for possible special disposal instructions.
DANGER: Do not open or mutilate the batteries. Released electrolyte is
corrosive and may cause damage to the eyes or skin. It may be toxic if
swallowed. ig
CAUTION: Exercise care in handling batteries in order not to short the
battery with conducting materials such as rings, bracelets, and keys. The
battery or conducts may
overheat and cause bums.
DO NOT ATTEMPT to remove cut material or hold material to be cut when
blades are moving. Make sure the trimmer switch is off when clearing jammed
material from the guard. Do not grasp the guard or blades when picking up or
holding the trimmer.
CAUTION: Lines coast after turned off.
DON’T FORCE GRASS TRIMMER – It will do the job better and with less Nall:
mod of a risk of injury at the rate for which it was designed.
STAY ALERT – Watch what you are doing. Use common sense. Do not operate
grass trimmer when you are tired or under the influence of drugs, alcohol or
medications. STORE IDLE GRASS TRIMMER INDOORS – When not Si used. the
grass trimmer should be stored indoors in a dry and high or locked-up place.
out of reach of children.
MAINTAIN TRIMMER WITH CARE – Keep clean for best performance and to
reduce the risk of injury. Keep handles dry, clean and free from oil and
grease.
WARNING: Do not operate the equipment while barefoot or when wearing
sandals or similar lightweight footwear. Wear protective footwear that wil
protect your feet and improve your footing on slippery surfaces.
WARNING: Use only identical manufacturer’s replacement parts. Use of any
other parts may create a hazard or cause product damage.
WARNING: Use only the manufacturer’s replacement blade in the cutting
head when using a grass trimmer attachment. Do not use any other cutting
attachment: for example, metal wire, rope, or the like. To install any other
brand of cutting head to the grass trimmer attachment can result in serious
personal injury.
FEATURES
PRODUCT SPECIFICATIONS
Model Number . ……………………. FH-GT120
Voltage . ……………………. 12V(Max)
Charger. ……………………. Slow charge(500mA)/Quick charge(1000mA)
Battery Capacity. ……………………. 1500mAh/2000mAh
Charging Time . ……………………. Slow charge(34H)/Quick charge(2-3H)
Lithium Battery. ……………………. 1500/2000 mAh
Cutting Diameter. ……………………. 140mm(5.5Inches)
No-load Time . ……………………. 1H(1500mAh)/2H(2000mAh)
Running time 20-30min (1500mAh)/30-40min(2000mAh)
No.
| Description| No.|
Description
---|---|---|---
1| Handle| 7| Protection Guard
2| Lock-Off Button| 8| Cutting Blade
3| Switch Trigger| 9| Auxiliary Handle
4| Locking Collar| 10| Battery Pack
5| Motor Housing| 11| Charger
6| Protective Wire| 12| Aluminum Rod
Demonstration of Installation Procedures of Mower
The package contains the following components:
- A charger
- A mower shield and a strip of anti-collision wire
- Spare blade, a blade base, a wrench, a blade locknut
- Work head of mower
- Middle connecting rod of mower
- One set of mower auxiliary handles, four fixed screws/nuts, one hexagon wrench
- Starting handle of the mower, one battery
- Manual
- A goggles
Charge the battery and open the package of accessories (1): A charger
- Connect the charger to the top charging hole of the battery, see Figure ①;
- The red indicator of the charger is on, meaning charging, see Figure ②;
- The green indicator is on, meaning charging completed, see Figure ③;
II.
Install the mower shield and anti-collision wire, and open the package of
accessories
(2) : A mower shield and a strip of anti-collision
wire
Notes: If no wire is installed, the blade may be damaged when operating the mower;
- The installation direction of the shield is close to the human during the operation process; see figure ①;
- Align the four-angle buckle of the shield at the cutter head slot of the mower, press down to the end, and then rotate until it aligns at the four-angle buckle of the cutter head, see Figure ②;
- Install the anti-collision wire, push the sides of the wire into the holes on both sides of the cutter head. The bottom of the wire contacts the ground in the correct installation method, see Figure ③;
Demonstration of the wrong installation of mower shield:
1)The shield is mounted in the opposite direction of the handle;
2)The bottom of the anti-collision wire is installed reversely without contact
with the ground;
III. Install the blade base and blade, and open the package of accessories (3)(4): Spare blade, a blade base, a wrench, a blade locknut, work head of mower
1)Align the opposite-side nut slot of the base to the mower motor or the nut
on the screw shaft.
The nuts of the cutter head should remain in the original position, see Figure
① ;
2)Install the blade in the base front blade slot. After the successful
installation, the cutter head screw should expose 1/3 inches, see Figure ②;
3)Install the blade locknut.
Note that the nuts with the pattern are downward (the wrong installation
will make the cutter head fall down), see Figure ③;
4)Tighten the blade locknut clockwise with a wrench, see Figure ④.
Demonstration of the wrong installation
1)Remove the nuts of the mower cutter head, see Figure ①;
2)The blade base is installed reversely, see Figure ②;
3)The blade locknut is installed reversely, see Figure ③
IV. Install the middle connecting rod of the mower and open the package of accessories (5): Middle connecting rod of mower
1)Align at the arrow marks on both ends of connecting rod and insert it, see
Figure①.
2)Align the plug at one end of the connecting rod with the slot at the other
end, see Figure②.
3)Referring to the rivets on the connecting rod, the upper and lower rivet
holes are inserted in a straight line inserted, see Figure③.
4)Tighten the lock sleeve of the rod in the locking direction, see Figure ④.
V. Install the auxiliary handle of the mower and open the package of
accessories (6); one set of mower auxiliary handle, four fixed screws/nuts,
one hexagon wrench 1)Adjust the installation position by itself according to
the height;
2)Open the rubber shock absorption sleeve of the handle, see Figure ①;
3)Install the lower base of the auxiliary handle, and pull the upper and lower
bases on the rubber shock Nabsorption cover to make the screw holes aligned,
see Figure ②;
4)Place the screws in the four holes and hold the= upper and lower bases, see
Figure ③;
5)Tighten screws with a hexagon wrench (prevent from screwing off), see Figure
④;
VI. Install the battery and open the package of accessories (7): Starting handle of the mower, one battery
1)Hold the clips on both sides of the battery, see Figure ①;
2)Align the battery slot buckle and push hard in. The sound means successful
installation, see Figure ②;
3)Remove the battery, hold the buckle on both sides of the battery, pull it
out of the slot and pull out the battery.
VII. Installation completed
VIII. Startup test
1)The starting handle includes the red round self-lock knob and the red long-
shaped start trigger, and the red round self-lock knob is the fuse button;.
2)The mower starts when pressing the fuse button before pulling the trigger,
see Figure ①;
3)After startup, release the round fuse button. Press the red long-shaped
start trigger to maintain working; release the trigger to stop working, see
Figure ②;
4)Repeat these steps 2) 3) to continue working.
MAINTENANCE
CAUTION: Do not at any time let brake fluids, gasoline, petroleum-based
products, penetrating oils, etc., come in contact with plastic parts. They
contain chemicals that can damage, weaken or destroy plastic. Make sure the
battery is detached (turn the unit, then use only mild soap and a damp cloth
to clean the tool. Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid. Fertilizers and other garden chemicals contain
agents which greatly accelerate the corrosion of metals Do not store the tool
on or adjacent to fertilizers or chemicals.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance
and adjustment should be performed by a qualified individual using only
Identical replacement parts.
If you drop the trimmer, carefully inspect it for damage. If the guard is bent
or cracked, handles broken or if you see any other condition that may affect
the trimmer’s operation, it must be repaired before putting it back into use.
Call our customer service helpline for assistance.
TROUBLESHOOTING
Problem
| Possible Cause|
Possible Solution
---|---|---
-Unit does not Run| -Battery is not making contact
-Trigger switch is not operational
-Battery was not installed properly
-Battery not charged| -Check battery is fully inserted
-Check that the lock-off button is fully depressed prior to move the trigger
-Check battery installation
-Check battery charging requirements
-Battery will not charge| -Battery not inserted into the charger
-Charger not plugged in
-Surrounding air temperature too hot or too cold| -Insert the battery into the charger until a red LED appears
-Plug charger into a working outlet
-Check current at receptacle by plugging in a lamp or other appliance
-Check to see if the receptacle is connected to a light switch which turns the power off when you turn out the lights
-Move charger and tool to a surrounding air temperature of about 39 degrees F (4 degrees C) or below 104 degrees F (+40 degree c)
POST-SALE CONTACT INFORMATION
Telephone: 571-313-0168
Email: shenzhenniumai@163.Com
URL: www.5startool.com
Facebook: https://www.facebook.com/kevein.jo
Youtube:https://www.youtube.com/channel/UCQzsxnaeX7QDTOwassFyfQg
CHECK OUR WEBSITE OR FACEBOOK FIRST FOR OUR FAQ, TUTORIAL VIDEOS, AND MAINTENANCE TIPS
Call us if you still have any questions about your grass trimmer between 10:00 AM — 6:00 PM EST, M-F
We will launch membership benefits. Join our Facebook group to get the following benefits:
- New product releases prioritize product experience
- Enjoy exclusive offers
- Exclusive customer service channel for members
- Lucky draw, send random gifts
Please take a minute for you to enter the link to join the group Facebook group link: https://www.facebook.com/groups/sznm888
After-sale card
If you have any product questions, please contact me as soon as possible, don’t hesitate!
Contact us
Contact: Customer Support
Address: 22500 Davis Drive, Suite 110 Sterling, VA 20164
Contact number: 571-313-0168
Email: shenzhenniumai@163.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>