Shenzhen Xiaoju Intelligent Technology N23 Smart Watch User Manual
- June 6, 2024
- Shenzhen Xiaoju Intelligent Technology
Table of Contents
Shenzhen Xiaoju Intelligent Technology N23 Smart Watch User Manual
A. Binding devices
a. Download and install
Download by scanning the code or searching the lnxFIT APP as follows.
Note: The equipment system platform needs to meet the requirements
-
Scan the QR code below to downloadhttps://web.xiaoju-smart.com/app_install.html
-
Open the mobile app store and search for” lnxFIT” to down load the app.
b. Binding method
( Note: During the tethering process lnxFIT will prompt you to turn on the
phone’s Bluetooth and authorize lnxFIT to access the GPS on your phone. If
there is an exception for IOS users tethering, please ignore this device in
your phone’s Bluetooth list first)
- Click “+” in the top right corner of the app home page and select” Add Device “to search Find the device that corresponds to your watch in the search list and tap to tether it.
- Click “+” in the top right corner of the app home page and select “Swipe” Scan the QR code displayed on the device the first time you turn it on, or if you accidentally exit, look for it on the device-Settings-About page
B. Data synchronization
The watch will generate and record your various data while you are wearing it, and you need to make sure the device is tied to the app before syncing.
This is done as follows. Open the lnxFIT App- drag down the page-sync starts with sync prompt and progress
C. Instructions for use
a. Charging schematic
Please connect and charge the device according to the picture instructions.
When starting up for the first time it is recommended to charge and turn on.
b. Wearing and adjustment
-
Wear (as accessories)
Please keep the watch one finger away from your wrist bone and adjust the strap length to a comfortable fit. -
Changing the strap
Push the switch sideways to loosen and remove the strap.
Note: Wearing too loosely or too tightly may affect the accuracy of heart rate or blood oxygen testing
D. Operating Instructions
a. Key operation
Short press on the button: back to the dial/ switch between dial and function list Long press button: On/Off
b. Replace the dial
Long press on the dial screen, the dial selection list appears after
vibration, swipe horizontally to select your Favorite dial and click to change
it.
c. Interface operation
Swipe the interface to enter different interfaces, the various interfaces are
shown as follows:
E. Function Overview
- Features
Exercise/ Heart Rate/ Blood Oxygen/ Sleep/ Alarm Clock/ Breathing Exercise/ Timer/ Weather/ Music Control/ Stopwatch
Note: The weather feature needs to be opened on the app to work properly. More feature details are available on the app.
2. Turn on the campaign
- a. Start exercise: click on the icon of the exercise function-select the type of exercise-after the countdown starts to detect the exercise data
- b. Motion control: Pause the movement-short press the side button. Resume movement: Press the side button briefly or tap the continue button on the screen
- c. To end the campaign: press and hold the side button or pause and select the end button on the screen
F. Product specifications
G. Cleaning and maintenance
It is recommended that products be worn and cleaned in accordance with the following three points.
- Keeping products clean
- Keep products dry
- Don’t wear it too tight
Do not use special cleaners to clean the unit; soap-free cleaners can be used. For stains that are not easy to remove, it is recommended to scrub with alcohol
H. Safety and certification (see the certificates).
The device meets the EU ROHS criterion.
Please refer to IEC 62321, EU ROHS
Directive 2011/65/EU and revised directive.
This device complies with Part 15 of the FCC Rules. Operation subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could avoid the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUCTIONS
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.
- Shenzhen XiaoJu Intelligent Technology Co.,Ltd
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>