SONOFF PIR3RF Motion Sensor User Manual
- June 6, 2024
- SonOFF
Table of Contents
SONOFF PIR3RF Motion Sensor
The device can be operated intelligently via working with the SON OFF 433MHz RF Bridge to communicate with other devices.
The device can work with other gateways supporting 433MHz wireless protocol. Detailed information is in accordance with the final product.
Operation instruction
-
Download APP
-
Pull out the battery insulation sheet
The device has the version with battery and without battery(Battery model: CR2450). -
Add sub-devices
Connect the Bridge before adding the sub-device.
Launch eWelink APP, select the Bridge to be paired, tap
“Add”and select “Alarm”, and you will hear a “Beep”that indicates the Bridge
enters the pairing mode, then short press the pairing button on the device (or
make the device detect the movement) that the pairing is successful when the
red LED keeps on for 1 sand the Bridge makes a”Bee p-Beep”so u n d.
If the addition failed, move the sub-device closer to the Bridge and try again.
Installation methods
- Method 1:
- Method 2:
- The motion sensor-base is not included, please purchase it separately.
- Do not install on the metal surface, otherwise it will affect the wireless communication distance.
- The device weight is less than 1 kg. The installation height of less than 2m is recommended.
Specifications
| Model | PIR3-RF |
|---|---|
| RF | 433MHz |
| Power supply | 3V button cell(Battery model: CR2450) |
| Detection Distance | 7m (Indoor space) |
| Detection angle | 110° |
| Working temperature | -10°(~40°( |
| Working humidity | 10-90%RH (non-condensing) |
| Material | PC |
| Dimension | 40x35x28mm |
Product Introduction
LED indicator status instruction
| LED indicator status | Status in struction |
|---|---|
| Red LED is stays on for 1s | A movement is detected |
| Red LED is stays on for 5s | Switched to the”home”mode |
| Red LED flashes twice | Low-battery notification |
| Green LED is stays on for 5s | Switched to the “away”mode |
Features
PIR3-RF is a 433MHz low-energy motion sensor that can detect the movement of
objects in real time. Connect it with the Bridge and you can create a smart
scene to trigger other devices.
Application Modes
The device has the “Normal” and “Alert” mode. The “Alert”mode is set by the
factory default.
In the “Alert” mode, long press the mode switching button for Ss until the LED
indicator stays solid red for Ss, which means the device enters the “Normal”
mode.
In the “Normal” mode, long press the mode switching button for Ss until the
LED indicator stays solid green for Ss, which means the device enters the
“Alert” mode.
FCC Warning
Changes or modifications not expressly approved by the party responsible for
compliance could avoid the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subjectto the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio
equipment type PIR3-RF is in compliance with Directive 2014/53/EU.The full
text of the EU declaration of conformity is available at the following
internet address:
https://sonoff.tech/usermanuals
Shenzhen Sonoff Technologies Co., Ltd
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>