SONOFF B02-F Series B02-F-A60 Wi-Fi Smart LED Filament Bulb User Manual

LBS BO2-F
User Manual V1.1

Wi-Fi Smart LED Filament Bulb

Operating Instruction

1. Install the device

To avoid electric shock, please turn off the power before installing the device.
The device works under 220-240V AC only.
2. Download APP

|
---|---
http://app.coolkit.cc/dl.html

3. Power on

After powering on, the device will enter the quick pairing mode (Touch) during the first use. The device enters the “breathing mode”.
The device will exit the quick pairing mode (Touch) if not paired within 3mins. If you want to enter this mode, please press the manual switch three times repeatedly at an interval of every ls (Off-ON-Off-ON-Off-ON). The “breathing mode” indicates the light enters quick pairing mode.

4. Add the device

Tap “+” and select” Quick Pairing”, then operate following the prompt on the app.

Compatible Pairing Mode

If you fail to enter Quick Pairing Mode (Touch), please try “Compatible Pairing Mode” to pair.

1. Press the light switch 5 times repeatedly at an interval of every 1s (Off-ON-Off-ON-Off-ON-Off-ON-Off-ON) when the light is on. The “quick flash” indicates the device enters the compatible pairing mode.
2. Tap “+” and select” Compatible Pairing Mode “on APP. Select Wi-Fi SSID with ITEAD-** and enter the password 12345678, and then go back to eWeLink APP and tap “Next”. Be patient until pairing completes.

Usage of being an ordinary bulb

Power on the bulb, it will enter quick pairing mode (The bulb change from bright to dim and cycle the mode), after 10s, if power off, it will go solid and keep warm light at the highest brightness.

Specifications

B02-F-A60, B02-F-S164: 220-240V AC 50Hz
Luminous Flux| B02-F-A19: 720Lm, B02-F-A60: 806Lm, B02-F-S164: 700Lm
Color temperature| B02-F-A19: 2700K-5000K, B02-F-A60: 2200K-6500K
B02-F-S164: 1800K-5000K
Rated power| B02-F-A19: 7.5W
B02-F-A60, B02-F-ST64: 7W
Lamp base| B02-F-A19: E26
B02-F-A60, B02-F-S164: E27
CRI| >_Ra80
Life Expectancy| 15000h
Wi-Fi| IEEE 802.11 b/g/n 2.4GHz
Operating systems| Android & iOS
Dimension| B02-F-A19: 60x110mm
B02-F-A60: 60x104mm
B02-F-ST64: 64x138mm

Product Introduction

Features

SONOFF LED is a LED smart bulb that allows users to adjust the brightness and color, and remotely turn on/off the connected devices via your smartphone, schedule it on/off and share it to your family to control together.

| | | |
---|---|---|---|---
Remote Control| Single/Countdown Timing| Voice Control| Share Control| Smart scene
| | | |
Sync Status| Stepless dimming|  Scene Mode| Camera Feature|  Group control

Factory Reset

Press the light switch 3 times repeatedly at an interval of every 1 s (Off-ON- Off-ON-Off-ON) when the light is on. The “breathing mode” indicates the device enters the quick pairing mode (Touch).

Please reset the device to factory defaults if you want to use other Wi-Fi networks, then reconnect the network.

Common Problems

Why does my device stay “Offline”?

1. Maybe you have entered the wrong Wi-Fi password.
2. Maybe there’s too much distance between the switch your router or the environment causes interference, consider getting close to the router. If failed, please add it again
3. The 5G Wi-Fi network is not supported and only supports the 2.4GHz wireless network.
4. Maybe the MAC address filtering is open. Please turn it off.
   If none of the above methods solved the problem, you can open the mobile data network on your phone to create a Wi-Fi hotspot, then add the device again.

FCC Warning

Changes or modifications not expressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type B02-F-A60/B02-F-ST64 is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address: https://sonoff.tech/usermanuals

Shenzhen Sonoff Technologies Co., Ltd.
1001, BLDG8, Lianhua Industrial Park,
Shenzhen, GD, China ZIP
code: 518000 Website: son of. tech
MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>