Showlite FLP-144 Flatline Panel LED Spotlight 144x 10 mm User Manual

October 27, 2023
SHOWLITE

Showlite FLP-144 Flatline Panel LED Spotlight 144x 10 mm User Manual
LOCKLY GUARD INGRESS 302 Smart Access Control and
Doorbell

Introduction

Thank you for your purchase of the Showlite Flood Light Panel.

We hope that you will enjoy the use of the Showlite Flood Light Panel.

Please read through this manual carefully before beginning to use, so that you will be able to take full advantage of the Showlite Flood Light Panel features and enjoy trouble-free operation for years to come.

Please keep this manual at a safe and dry place where you easily can access it.

Warning IconCaution!
Before switching on the instrument or device read carefully the safety instructions to avoid serious injuries or damage of the product.

Technical data

Type 144 x 10mm LED
Art. 00031047
Color Mixing 144 LED / RGB mixing
Power Supply 90-240V – 50/60Hz
Power consumption 15 Watt
Operating temperature -20° … 40°
angle of radiation 25°
Connectors DMX in/out (XLR)

Power In/Out
DMX channels| 3/6 DMX channel modes
accessories| Anschraubbare Rine, Netzkabel
adjustable stands, net cable
Dimensions (WxHxD)| 225 mm x 220mm x 85mm
Weight| 1.5 kg

Reset Programs

Program

| Function|

SP 1 … SP 2

---|---|---
1| chaser light all colors| 1.2 sec
2| chaser light| 0.4 sec
3| fading warm colors| 0.5-1.5 sec
4| fading cold colors| 0.5-1.5 sec
5| warm color strobe| 0.1-1.0 sec
6| flashing cold color strobe| 0.1-1.0 sec
7| wesmooth fading all colors| 0.3-1.3 sec
8| white strobe| 1 Hz … 15Hz

Operator Guidance chart

Operator Guidance

Appendix 1 -DMX512 channel list

3CH mode

Channel

| Value|

Function

---|---|---
CH 1| 0-255| Red (0%–100%)
CH 2| 0-255| Green (0%–100%)
CH 3| 0-255| Blue (0%-100%)

6CH mode

Channel

| Value|

Function

---|---|---
CH 1| 0–255| Dimmer (0%-100%)
CH 2| 0–255| Red (0%–100%)
CH 3| 0–255| Green (0%–100%)
CH 4| 0–255| Blue (0%–100%)
CH 5| 0–255| Speed (slow — fast)
CH 6| 0-15| no functon
16-31| Sence R-G-B-RG-G
32-47| Sence G-GB-B-RB-R
48-63| Sence R-B-G-RG-G
64-79| Sence R-G-GB-RBG-G
80-95| Sence B-BG-RGB-RG-G
96-111| Color sync strobe
112-127| Color fade
128-143| Color change
144-159| Color change and strobe
160-175| Color fast in slow out
176-191| Color slow in fast out
192-207| Color slow in slow out 1
208-223| Color glide
224-239| Sound 1
240-255| Sound 2

Power connection and DMX

After save installation (floor or overhead) please connect the power cable to net voltage like listed in technical data. You can operate the lighting device by an external DMX controller or by internal preset programs. If using a DMX controller connect the controller DMX-OUT with the lighting DMX-IN. To connect several lighting effects set up a DMX loop by connecting DMX-OUT of first device with DMX-IN of second device and so on.

DMX-connectors and backside operator panel:
Power connection

Preset Programs / parameter settings

All parameter settings and preset programs can be changed and selected on the backside operator panel . After first power on the display shows A001 — by pressing [ENTER] button, the display shows selected DMX address. By pressing [UP]/[DOWN] you can adjust the address and save with [ENTER] button. Display is showing AXXX ( XXX = selected DMX address).
By pressing [UP]/[DOWN] buttons you can select the sub menus AUto, Chnd (DMX), Colo, SoUn, SLAv and ugr. Select a menu and press [ENTER], display will change to parameter menu where you can change the particular parameter settings by pressing [UP]/[DOWN]. Parameters can be changed and saved by [ENTER] button.

Preset programs:
Select Mode menu by pressing [UP]/DOWN] and accept by pressing [ENTER]. Display will change to preset programs to be selected by [UP]/[DOWN]. By pressing [ENTER] you step into sub menu where you can adjust specific preset parameters (color, speed, etc.).

Addr DMX address setting A001 to A512
Auto 8 Auto presets — adjustable speed in 9 steps
SoUn 8 Sound presets like Auto but sound controlled
Colo 1..9 color mixing presets / individual RGB color mixing (Atf)
Chnd Select DMX channel mode
SLAv switch device to SLAVE mode
ugr software version is displayed

In Auto mode the speed can be adjusted in 9 steps SP01…SP09. In Sound mode the light effect will be controlled by the built in microphone (backside).

Precautions

Please read carefully before proceeding

Warning:
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

Power supply / power cord (devices with power cords/power supplies):

  • Only use the voltage specified as correct for the device. The required voltage is printed on the type plate of the device. Check the power cable from time to time regarding dirt, damage or other influence.
  • Use only the included power cord / power supply or adaptor. Do not place the power chord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it.
  • Remove the electric plug from the outlet when the device is not to be used for extended periods of time, or during electrical storms. When removing the electric plug from the device or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it.
  • To avoid generating unwanted noise, make sure there is adequate distance (50 cm or more) between the AC power adaptor and the device. Do not cover or wrap the AC power adaptor with a cloth or blanket.

Batteries / safety instructions (devices with batteries):

  • Use only high quality batteries — do not mix batteries with rechargeable accumulators
  • Do not try to recharge non-rechargable batteries
  • Keep attention to the polarity when changing the batteries (polarity is signed on the device)
  • Do not cause an electrical short at the batteries, do not open the batteries
  • Changing of batteries must not be done by children, do not let children play with batteries
  • Remove batteries from the device when the dDevice is not in use for a longer period
  • Batteries are special waste, do not dispose them with the domestic waste

Location:

  • When setting up the device, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product all the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet.
  • Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fire.
  • Do not expose the device to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration or damage to the internal components.
  • Do not place the device in an unstable position where it might accidentally fall over.
  • Do not block the vents. This device has ventilation holes at the bottom/rear to prevent the internal temperature from becoming too high. In particular, do not place the device on its side or upside down. Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fire.
  • Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Doing so may result in noise, both in the device itself and in the TV or radio next to it.

Connections and handling:

  • Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum.
  • Do not use the device or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician.
  • Do not rest your weight on the device or place heavy objects on it, and avoid use excessive force on the buttons, switches or connectors

Do not open:

  • Do not open the device or attempt to disassemble the internal parts or modify them in any way. The device contains no user-servicable parts. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified service personnel.

Water warning:

  • Do not expose the device to rain, use it near water or in damp or wet conditions on it containing liquids which might spill into any openings. Never insert or remove an electric plug with wet hands.

If you notice any abnormality:

  • If the power cord or plug becomes frayed or damaged, or if there is a sudden loss of sound during use of the device, or if any unusual smells or smoke should appear to be caused by it, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified service personnel.

INSTALLATION

The Showlite Flood Light Panel is designed as floor effect or for overhead rigging on stages, in discotheques, theatres, etc. During installation consider all necessary safety instructions especially EN 60598-2-17 and national standards. Please note: for overhead rigging in public or industrial areas, a series of safety instructions have to be considered. This manual can only give a survey and does not list complete instructions. Installation must only be done by authorized and experienced operators.

Overhead rigging

Important! Overhead rigging must only be done by authorized and experienced operators. Always install an appropriate safety bond.

You must only use safety bonds and quick links complying with DIN 56927, shakles complying with DIN EN 1677-1 and BGV C1 carbines.All devices must be sufficiently dimensioned and used correctly in accordance to the latest industrial safety regulations.

The installation oft he device hast o be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation.
The maximum drop distance must never exceed 20 cm.

A safety bond which already held the strain of a crash or which is defective must not be used again.

WEEE declearation

Your product is designed and manufactured with materials and components of high quality, which are recyclable and can be reused. The symbol means that your product should be disposed of separately from household waste when it reaches its end of life. Please dispose of this equipment at your local collection point or recycling center. Please help to protect the environment in which we all live.

All specifications and appearances are subject to change without notice. All information was correct at time of printing. Musikhaus Kirstein GmbH does not guarantee for the accuracy or completeness of any description, photograph or statement contained in this manual. Printed colors and specifications may vary slightly from product. Products from Musikhaus Kirstein GmbH are only sold through authorized dealer. Distributors and dealers are not agents of Musikhaus Kirstein GmbH and have no authority to bind Musikhaus Kirstein GmbH legally in any way. This manual is protected by copyright. Any copying or reprint, even in excerpts, is only allowed with written consent of Musikhaus Kirstein GmbH. The same applies to reproduction or copying of images, even in altered form.

Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals