00028581 Showlite LED Stage Bar User Manual
- June 5, 2024
- SHOWLITE
Table of Contents
00028581 Showlite LED Stage Bar
User Manual
Precautions
Please read carefully before proceeding
Warning:
Always follow the basic precautions listed below to avoid the possibility of
serious injury or even death from electrical shock, short-circuiting, damages,
fire or other hazards. These precautions include, but are not limited to, the
following:
Power supply I power cord (devices with power cords/power supplies):
-
Only use the voltage specified as correct for the device. The required voltage is printed on the type plate of the device.
Check the power cable from time to time regarding dirt, damage or other influence. -
Use only the included power cord I power supply or adaptor. Do not place the power chord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it.
-
Remove the electric plug from the outlet when the device is not to be used for extended periods of time. or during electrical storms. When removing the electric plug from the device or an outlet. always hold the plug itself and not the cord. Pulling by the cord can damage it.
-
To avoid generating unwanted noise. make sure there is the adequate distance (50 cm or more) between the AC power adaptor and the device. Do not cover or wrap the AC power adaptor with a cloth or blanket.
Batteries I safety instructions (devices with batteries):
- Use only high-quality batteries — do not mix batteries with rechargeable accumulators
- Do not try to recharge non-rechargable batteries
- Keep attention to the polarity when changing the batteries (polarity is signed on the device)
- Do not cause an electrical short at the batteries, do not open the batteries
- Changing of batteries must not be done by children, do not let children play with batteries
- Remove batteries from the device when the device is not in use for a longer period
- Batteries are special waste, do not dispose of them with the domestic waste
Location:
- When setting up the device, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs. immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product all the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet.
- Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fire.
- Do not expose the device to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration or damage to the internal components.
- Do not place the device in an unstable position where it might accidentally fall over.
- Do not block the vents. This device has ventilation holes at the bottom/rear to prevent the internal temperature from becoming too high. In particular, do not place the device on its side or upside down. Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fire.
- Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices.
Doing so may result in noise, both in the device itself and in the TV or radio next to it.
Connections and handling:
- Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum.
- Do not use the device or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician.
- Do not rest your weight on the device or place heavy objects on it, and avoid use excessive force on the buttons, switches or connectors
Do not open:
- Do not open the device or attempt to disassemble the internal parts or modify them in any way. The device contains no user-servicable parts. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified service personnel.
Water warning:
- Do not expose the device to rain, use it near water or in damp or wet conditions on it containing liquids that might spill into any openings. Never insert or remove an electric plug with wet hands.
If you notice any abnormality:
- If the power cord or plug becomes frayed or damaged, if there is a sudden loss of sound during the use of the device, or if any unusual smells or smoke should appear to be caused by it, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified service personnel.
INSTALLATION
The Showlite Stage Bar LED-lighting effect is designed as a floor effect or
for overhead rigging on stages, in discotheques, theatres, etc. During
installation consider all necessary safety instructions especially EN
60598-2-17 and national standards. Please note: for overhead rigging in public
or industrial areas, a series of safety instructions have to be considered.
This manual can only give a survey and does not list complete instructions.
Installation must only be done by authorized and experienced operators.
Overhead rigging
Important! Overhead rigging must only be done by authorized and experienced
operators. Always install an appropriate safety bond.
You must only use safety bonds and quick
links complying with DIN 56927, shackles complying with DIN EN 1677-1, and BGV
C1 carbines. All devices must be sufficiently dimensioned and used correctly
in accordance to the latest industrial safety regulations.
The installation of the device has o be built and constructed in a way that it
can hold 10 times the weight for 1 hour without any harmful deformation.
The maximum drop distance must never exceed 20 cm.
A safety bond that already held the strain of a crash or which is defective
must not be used again.
Power connection and DMX
After saving installation (floor or overhead) please connect the power cable to the net voltage as listed in the technical data. You can operate the lighting device by an external OMX controller or by internal preset programs. If using an OMX controller connect the controller OMX-OUT with the lighting OMX-IN. To connect several lighting effects set up an OMX loop by connecting OMX-OUT of the first device with OMX-IN of the second device and so on.
Preset Programs I parameter settings
All parameter settings and preset programs can be changed and selected on the
backside operator panel. After the first power on the display shows A001 — by
pressing the [ENTER] button, the display shows the selected OMX address. By
pressing [UP]/[DOWN] you can adjust the address and save it with the [ENTER]
button. Display is showing AXXX ( XXX = selected OMX address). By pressing
[UP/[DOWN] buttons you can select the sub menus AUto, Chad (DMX), Colo, SoUn,
SLAv, and age. Select a menu and press [ENTER], display will change to the
parameter menu where you can change the particular parameter settings by
pressing [UP]/[DOWN]. Parameters can be changed and saved by the [ENTER]
button.
Preset programs:
Select the Mode menu by pressing [UP]/[DOWN] and accept by pressing [ENTER].
The display will change to preset programs to be selected by [UP]/[OOWN]. By
pressing [ENTER] you step into a sub-menu where you can adjust specific
preset parameters (color, speed, etc.).
Addr | OMX address setting A001 to A512 |
---|---|
Auto | 3 Auto presets — fade effects, chaser (1 ), chaser (2) |
Chad | OMX channel mode 3/5/8/14/24/26 channels |
Colo | 1..9 color mixing presets I individual RGB color mixing (ATF) |
sound | 3 Sound presets — flash effects (strobe), chaser (1), chaser (2) |
Chad | Select OMX channel mode |
Slav | The device is working in SLAVE mode |
ugr | the software version is displayed |
In Auto mode the speed can be adjusted in 9 steps SP01 … SP09. In Sound mode,
the light effect will be controlled by the built-in microphone (backside). You
can adjust microphone sensitivity by using the control on the backside.
See the complete operator guidance chart in Appendix 2
Appendix 1– DMX512 channel list
3CH | 5CH | 8CH | 14CH | 24CH | 26CH | Function |
---|---|---|---|---|---|---|
1 | 3 | 3 | 3 | 1 | 3 | R |
2 | 4 | 4 | 4 | 2 | 4 | G |
3 | 5 | 5 | 5 | 3 | 5 | B |
6 | 6 | 4 | 6 | W | ||
7 | 7 | 5 | 7 | R | ||
8 | 8 | 6 | 8 | G | ||
9 | 7 | 9 | B | |||
10 | 8 | 10 | W | |||
11 | 9 | 11 | R | |||
12 | 10 | 12 | G | |||
13 | 11 | 13 | B | |||
14 | 12 | 14 | W | |||
13 | 15 | R | ||||
14 | 16 | G | ||||
15 | 17 | B | ||||
16 | 18 | W | ||||
17 | 19 | R | ||||
18 | 20 | G | ||||
19 | 21 | B | ||||
20 | 22 | W | ||||
21 | 23 | R | ||||
22 | 24 | G | ||||
23 | 25 | B | ||||
24 | 26 | W | ||||
1 | 1 | 1 | 1 | LED the main function | ||
2 | 2 | 2 | 2 | Speed, slow to fast | ||
LED main | 0-7: | 8-15: | 16-23: | 24-31: | 224-231 | |
--- | --- | --- | --- | --- | --- | --- |
function | dimmer | strobing | model | model | mode27 | |
function speed |
Appendix 2-Bedienstruktur/operator guidance chart
Appendix 3 -Technische Oaten I Technical data
Typ/Type | 216 x 10mm LED | 8 x 3 Watt LED | 16 x 3 Watt LED |
---|---|---|---|
Art.Nr. | 28581 | 28582 | 28583 |
Farbmischung
Color Mixing| R72 / G72 / B72
9 Segmenten| 3 in 1 LEDs RGB| 3 in 1 LEDs RGB
Spannungsversorgung
Power Supply| 110V 240V – 50/60Hz
Leistungsaufnahme
Power consumption| 25 Watt| 30 Watt| 60 Watt
Betriebstemperatur
Operating temperature| -20° … 40°
Abstrahlwinkel
angle of radiation| 25°
Anschliisse
Connectors| DMX in/out (XLR)
Power in (110-240V)
| | |
DMX channels| 3, 5, 8, 14, 24, 26 DMX Channel Modes
Zubehor
accessories| Anschraubbare Fiii6e, Netzkabel
adjustable stands, net cable
Abmessungen
(BxHxT)
Dimensions (WxHxD)| 975 mm
67mm
63mm| 500 mm
67mm
110mm
153mm| 965 mm
64mm
Gewicht
Weight| 2.2 kg| 2.6 kg| 5.3 kg
WEEE declaration
Your product is designed and manufactured with materials and components of
high quality, which are recyclable and can be reused. The symbol means that
your product should be disposed of separately from household waste when it
reaches its end of life. Please dispose of this equipment at your local
collection point or recycling center Please help to protect the environment in
which we all live.
All specifications and appearances are subject to change without notice. All
information was correct at the time of printing. Musikhaus Kirstein GmbH does
not guarantee the accuracy or completeness of any description, photograph, or
statement contained in this manual, Printed colors and specifications may vary
slightly from product. Products from Musikhaus Kirstein GmbH are only sold
through authorized dealer Distributors and dealers are not agents of Musikhaus
Kirstein GmbH and have no authority to bind Musikhaus Kirstein GmbH legally
in any way. This manual is protected by copyright. Any copying or reprint,
even in excerpts, is only allowed with the written consent of Musikhaus
Kirstein GmbH, The same applies to reproduction or copying of images, even in
altered form.
Musikhaus Kirstein GmbH
Bernbeurener Strasse 11- D-86956 Schongau
Tel. 0049-8861-909494-0
Documents / Resources
|
SHOWLITE 00028581 Showlite LED Stage
Bar
[pdf] User Manual
SB-216, 00028581 Showlite LED Stage Bar, 00028581, Showlite LED Stage Bar
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>