KOAMTAC KDC80 Bluetooth Barcode Scanner User Guide
- June 6, 2024
- KOAMTAC
Table of Contents
KDC80
Quick Guide
116 Village Blvd, Suite 305, Princeton, NJ 08540 USA
T: + 1-609-256-4700 F:
+1-609-228-4373
info@koamtac.com
www.koamtac.com
©2020,2021 KOAMTAC, Inc.
QG_KDC80_20211221
Product Introduction
The KDC80 Bluetooth barcode scanner is a 1D Laser/CCD Bluetooth Barcode Data Collector supporting Bluetooth Low Energy (BLE) v5.0.
KDC80 Diagram
How to turn on and off
Refer to the figure in section 1.1 to locate the SCAN and DOWN buttons.
Note: The trigger on the Ring Scanner and Finger Trigger Glove work as SCAN
buttons.
a) Press and hold the SCAN + DOWN buttons simultaneously for 3 seconds.
b) The KDC will beep when it is turned ON.
c) Press and hold the SCAN + DOWN buttons simultaneously for 3 seconds again
to turn off the KDC.
Pairing (Bluetooth or NFC)
Connecting your KDC using Bluetooth is made easy with the below-pairing
barcodes.
If using an Android device, pairing via NFC is even easier: just approaching
the KDC to the back of the host device’s NFC area is enough for pairing. For
more details, see section 2.3
Bluetooth Profiles Explained
a. HID Profile: This allows one-way Bluetooth communication with an Android or
iOS host device. The KDC only transmits data to the host device.
b. SPP Profile: This allows two-way Bluetooth communication. The KDC transmits
data to the host device and the host device can transmit data back to the KDC.
c. HID Windows Profile: Allows one-way Bluetooth communication with Windows
host device. The KDC only transmits data to the host device.
Note: HID inputs data directly into an application. SPP requires the KOAMTAC SDK to input data into an application. To gain access to the SDK, please complete the form here: https://www.koamtac.com/sdk/
Bluetooth Pairing a KDC80 to your smart device with special barcodes
a. Navigate to the Bluetooth setting on the host device and ensure that
Bluetooth is both enabled and searching for devices.
b. Using the KDC, scan the pairing barcode above that corresponds to your
desired Bluetooth profile. If you are unsure which Bluetooth profile is right
for you, please refer to Chapter section 2.1.
- If you use an Android, iOS, or Mac device and desire an HID connection, then scan barcode #1 above.
- If you use a Windows device and desire an HID connection, then scan barcode #2 above.
- If you desire an SPP connection for any device, then scan barcode #3 above.
c. In HID or HID Windows Profile, check the list of available Bluetooth
devices on your host device. From the list, select the KDC80 listed by serial
number in brackets that match the serial number found on the backside of the
KDC80. KDC80 will beep upon connection and display “Bluetooth Connected” on
its screen. Now it is ready to use.
d. In SPP Profile for non-iOS, check the list of available Bluetooth devices
on your host device. From the list, select the KDC80 listed by serial number
in brackets that match the serial number found on the backside of the KDC80.
KDC80 will beep upon connection and display “Bluetooth Connected” on its
screen, but you should launch KTSync or your application and select KDC80
within the application to complete the connection. Now it is ready to use.
e. In SPP Profile for iOS, the KDC is NOT listed on your host device, so you
should launch KTSync or your application and select the KDC80 listed by serial
number in brackets that matches the serial number found on the backside of the
KDC80. KDC80 will beep upon connection and display “Bluetooth Connected” on
its screen. Now it is ready to use.
Bluetooth Pairing a KDC80 to your smart device with NFC (Android Only)
This feature applies only to Android. KDC may be paired in either HID or SPP
only.
a. Navigate to the NFC setting on the host device and ensure that Bluetooth is
both enabled and searching for devices.
b. On the KDC, make sure NFC pairing is enabled by navigating to KDC MENU →
BLE Config →NFC Pairing → Enabled → Save & Exit.
c. On the KDC, select the pairing profile by navigating to KDC MENU → BT
Config → Connect Device → Select HID or SPP → Save & Exit.
Or, select the profile using the special barcodes below:
a. Approach the NFC area on the back of the host device with the KDC to complete pairing.
Usage
Using Keyboard Wedge (HID Keyboard)
This option is only available using a Bluetooth connection with HID profile.
Once the KDC is paired with the host, open any application with a text field
and tap on the text field. Scan any barcode and it will populate in the text
field.
Using KTSync – Android/iOS
You can use KTSync to utilize your KDC alone or with a native application.
This is only available using a Bluetooth connection with SPP or MFi.
a) Download and install KTSync from the Google Play Store or the Apple App
Store.
b) Open KTSync and tap on the “Connect” option on the bottom left to view a
list of available devices. (Fig. 1)
c) From the device list, select your KDC – ensuring that the serial number
displayed in brackets matches the serial number on the back of your KDC. (Fig.
2)
d) Upon successful connection, KTSync will display “Connected” next to the
name of your KDC at the top of the application. (Fig. 3)
e) To test your connection, scan any barcode. If the connection is successful,
the barcode data will display on the screen. (Fig. 3)
In Always-pairing mode, an application can connect to a KDC without reading a
pairing barcode, so the connection procedure is a little different.
a) In the KTSync app, tap the Connect icon at the bottom left of the app.
b) In KTSync, tap “Start BLE Scanning” in the top right.
c) In KTSync, check the list of found devices.
d) In KTSync, tap the KDC80 listed by serial number in brackets followed by
[BLE] that matches the serial number found on the backside of the KDC80. The
format will look like this, KDC80[xxxxxx] [BLE], where xxxxxx is the serial
number.
e) The KDC80 will beep upon connection and display “Bluetooth Connected” on
its screen. Now it is ready to use.
Using KTSync Keyboard – Android
Once your KDC is connected to KTSync, you can use your KDC as a keyboard.
a) While KTSync is running in the background, navigate to Settings > Language
& Input > Virtual Keyboard > Manage keyboards
b) Tap on “KTSync Keyboard” to enable it.
c) Change “KTSync Keyboard” to the default keyboard. (Fig. 5)
To switch back to the previous keyboard, simply change the default keyboard
again. Or, when a text field is selected swipe down from the top of the screen
to bring up the notification panel. Select ‘choose input method’ and you can
select the default keyboard from here. (Fig. 6)
Using KTSync Keyboard – iOS
Once your KDC is connected to KTSync, you can use your KDC as a keyboard.
a) Navigate to the iPhone/iPad/iPod Settings > General > Keyboard > Keyboards
Add New Keyboard… > Select the KTSync keyboard to be added. (Fig. 7)
b) Select the KTSync Keyboard and toggle the switch to Allow Full Access. (Fig. 8)
c) Open the application you want to scan into and tap on the screen, so the
on-screen keyboard appears.
d) Press and hold the globe icon located to the left of the spacebar.
e) Select the KTSync Keyboard and begin scanning. (Fig. 9)
Note: The KDC must be connected to KTSync & the KTSync keyboard must be selected for this to work.
Using other Developed Applications with SDK – Android/iOS
A Software Development Kit (SDK) for Android and iOS is available to all
KOAMTAC customers to ensure the smooth development of applications that work
seamlessly with a KDC scanner. It’s easy to request the SDK from the KOAMTAC
website: a) On any web browser, open www.koamtac.com
b) Navigate to Support > Downloads > SDK
c) Complete the form and submit it.
After submission, a KOAMTAC representative will reach out regarding the next steps for completing the SDK Agreement.
The SDK package will have libraries, documents, a sample application, and its source code.
Product Specifications
Physical | Design | Companion Bluetooth Barcode Scanner |
---|---|---|
Size | 1.3 inx 2.4 inx 0.6in/34 mmx62 mmx 15 mm | |
Weight | KDC80 Laser: 1.2 oz / 35 g KDC80 CCD: 1.0 oz / 30 2 | |
Functionality | Supporting OS | Android / OS / Windows / Mac OS X |
Keys | Scan Key, Up Key, Down Key | |
Buzzer | Yes | |
LED Indicator | 1 Status LED (Red / Amber / Green) | |
USB Port | 1 Type-C USB Port | |
Memory | RAM | SDRAM 256KB |
ROM | Program Flash ROM 1MB User Data Flash ROM 5MB | |
Barcode Storage | 262,000 Barcodes (EAN-13) | |
Power | Battery (Standard) | 200 mAh Lithium-Polymer |
Charging Solution | USB Connector | |
Charging Time | 3 Hours | |
Communication | Bluetooth | Bluetooth Low Energy V5.0, HID/SPP |
Type-C USB | USB Flash Memory (Windows) |
USB HID
USB Serial (Android with OTG cable / Windows)
Barcode Reader| 1D/2D Symbology| Yes
of scans per charge
(1-sec interval)| >TBD
of scans per charge
(10-sec interval)| >TBD
Scan Range (20mil Code39)| 1.97″ to 18.11″ (50 mm to 460 mm)
Screen Reading| Yes (only for KDC80 CCD)
Postal Codes / OCR
Passport| No / No
Environment| Drop Spec| 4 ft (1.2 m)
5 ft (1.5 m) with a protective boot
IP Rating| IP42
Operating Temp.| 14ºF to 122 ºF (-10 °C to 50ºC)
Storage Temp.| -4 ºF to 140 ºF (-20 ºC to 60 °C)
Humidity Spec| 5% – 95% (non-condensing)
Regulatory
Conformance| Laser Safety| IEC60825-1 (Class II) (KDC80 Laser Model)
LED Safety| IEC62471:2006 (KDC80 CCD Model)
Regulatory| CE, FCC, KC, J-MIC, VCCI, SRRC, RoHS Compliant
Accessories| Charging Cradle| No
Finger Trigger Glove / Ring| No
| Protective Boot| Yes
---|---|---
Social Distancing Feature
The COVID-19 pandemic has added a new challenge to every workplace –
warehouses, manufacturing lines, and even retail store floors – the need to
maintain distance between people for their health and safety. Reopening your
business is already an undertaking but ensuring social distance among your
workers is made easy with the KOAMTAC social distancing feature.
Whether you’re a small or enterprise business, the KOAMTAC social distancing
feature works with the technology and systems you already have in place so
you, and your workers, can have peace of mind as you adjust to the new normal.
- Supported on all Bluetooth Low Energy (BLE) 5.0 KDC devices.
- For more on the social distancing feature, please watch: https://youtu.be/m4Manx9vK68
There are three ways to enable and control the settings for the social distancing feature:
- Enable via the KDC menu
- Scan the special Social Distance barcodes that correspond with the settings you wish to enable
- Enable via the KTSync application
KDC80 does not have a vibrate feature. So please ignore the vibrate for Social Distancing Feature.
Social Distancing Feature Parameters
The following parameters can be changed:
- Distance: Set the acceptable social distance range with values between 1 to 10 meters (Default: Disabled).
- Host Alert: This setting will forward distance alerts to the connected host device (Default: Disabled).
- KDC Alert: This setting allows the user to enable/disable an audible beep sound (Default: Enabled), vibration (Default: Disabled), and data storage (Default: Disabled) settings for distance violations on the KDC.
- Security Key: Choose between a fixed key or a custom key. Only KDC devices using the same key will be able to detect and report the distance between devices. If the fixed key is selected, the KDC will use a predefined key. If you prefer to set your own custom key, this action can only be performed by using KTSync (Default: Fixed Key).
Enabling the Social Distancing Feature via the KDC Menu
If you prefer to enable the social distancing feature by navigating through
the KDC menu, then follow the instructions below:
a) From the KDC BLE Config menu, select Social Dist. to configure
b) Set the Distance from 1m to 10m
c) Set the Host Alert to enable/disable
d) Set the KDC Alert: Beep, Vibrator, and Data Store to desired settings
e) Set the Security Key: Fixed Key or Custom Key
Enabling the Social Distancing Feature via Social Distance Barcodes
If you prefer to enable the social distancing feature via special barcodes, scan the special social distance barcodes that correspond with the settings you wish to enable:
Enabling the Social Distancing Feature via the KTSync application
The social distancing feature can also be configured in the KTSync application.
-
Note: This menu is only shown when KTSync is connected to a KDC BLE device running firmware version 050025 or higher.
a) Open KTSync and tap the Setting icon
b) Select KDC Menu (Fig. 10)
c) Select Social Distance Finding (Fig. 11)
d) Choose your Social Distance settings. Settings listed in the KDC Configuration section are the same settings available to you as if you were setting parameters on the KDC itself. These settings will be saved when you exit this screen. (Fig. 12)
e) Additional Application Configuration settings can be set on this screen as well. (Fig. 12)- Enable Vibrator: If enabled, the host device vibrates when receiving social distance alert data.
- Enable Email Sending: If enabled, an email application is launched instead of a social distance data pop up when receiving social distance alert data.
- Email Address: Register an email address to send social alert events.
Examples of Social Distance Alerts & Social Distance Alert Data
Whenever the KDC is connected, the KDC is sending social distance alert data to the host device if the host alert is enabled and another KDC is found within the selected distance range. When a social distance violation occurs, you may receive these alerts, depending on settings:
- Social distance warning on KDC, showing your KDC serial number accompanied by beep/vibrate if selected. (Fig. 13)
- Social distance pop-up in KTSync showing your KDC serial number, the date & time of the violation, the serial number of the other detected KDC, and the distance if using the host alert setting. (Fig. 14)
- Social distance email showing your KDC serial number, the date & time of the violation, the serial number of the other detected KDC, and the distance if using the enable email sending set. (Fig. 15)
Note: When reconnected, the KDC will send social distance data to the host device even if the same KDC is found within distance.
Note: Only one social distance data alert is sent to the host device when multiple KDC devices are detected if the social alert is already being displayed as a pop-up or email application is already launched.
KOAMTAC devices and accessories are not designed or intended to prevent,
mitigate, treat, diagnose or cure any disease or health condition, including
COVID-19/Coronavirus. KoamTac devices and accessories are intended for general
public use only.
KOAMTAC devices and accessories are not medical devices and are not intended
for use in any medical or inherently infectious setting, or where exposure to
bodily or hazardous fluids may be expected, or where the risk of exposure
through inhalation is high.
KOAMTAC DEVICES ARE PROVIDED AS-IS WITH ALL FAULTS, AND KOAMTAC SPECIFICALLY
DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING (WITHOUT LIMITATION)
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
KOAMTAC SPECIFICALLY DISCLAIMS THAT KOAMTAC DEVICES WILL PREVENT INFECTION OR
THE TRANSMISSION OF VIRUSES OR DISEASES. KOAMTAC DEVICES ARE NOT A SUBSTITUTE
FOR PROFESSIONAL MEDICAL ADVICE, DIAGNOSIS, OR TREATMENT, AND ANY MEDICAL
QUESTIONS SHOULD BE DIRECTED TO YOUR HEALTHCARE PROVIDER. THE ENTIRE RISK AS
TO THE QUALITY AND PERFORMANCE OF THE SOCIAL DISTANCING FEATURE OF THE PRODUCT
IS WITH THE BUYER. SHOULD THE QUALITY OR PERFORMANCE OF THE SOCIAL DISTANCING
FEATURE OF ANY KOAMTAC PRODUCTS PROVE DEFICIENT FOLLOWING ITS PURCHASE, THE
BUYER ALONE, AND NOT THE MANUFACTURER, DISTRIBUTOR, OR RETAILER ASSUMES THE
RISK OF ANY INFECTION OR DISEASE TRANSMISSION THAT MAY RESULT DURING BUYER
USAGE. KOAMTAC ASSUMES NO LIABILITY FOR INACCURACIES OR MISSTATEMENTS BY
THIRD-PARTY SELLERS.
See Reference Manual for more detailed information Visit
store.koamtac.com to purchase additional KDCs and
accessories.
QG_KDC80_20211221
References
- KOAMTAC Store – KOAMTAC Inc.
- KOAMTAC Store – KOAMTAC Inc.
- KOAMTAC Bluetooth Barcode Scanners, RFID Readers, and mPOS
- KOAMTAC Bluetooth Barcode Scanners, RFID Readers, and mPOS
- KTSync on the App Store
- Software Development Kit (SDK) for KOAMTAC Data Collectors (KDCs)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>