CERWIN-VEGA SH65F4B RPM Tower Speaker User Manual

June 6, 2024
cerwin vega

CERWIN-VEGA SH65F4B RPM Tower Speaker

Introduction

Cerwin Vega Mobile Speakers
Congratulations for purchasing Cerwin Vega Mobile speakers for your audio system. You have chosen Cerwin Vega Mobile because you deserve the best!
Cerwin Vega Mobile speakers are designed and engineered to reproduce great sound quality for many years of listening enjoyment in your vehicle!

We highly recommend that your new speakers be installed by an authorized Cerwin Vega Mobile dealer. Your authorized dealer can professionally assemble/disassemble the interior of your vehicle and set the proper speaker placement for ideal sound quality.

If you decide to install the speakers by yourself, please thoroughly read through this manual before getting started. This manual will help familiarize yourself with these speakers and guide you through the installation process and procedures.

Please contact your local authorized Cerwin Vega Mobile dealer if you have any questions regarding the instructions in this manual. If you require additional assistance, please contact the Cerwin Vega Mobile Technical Support Department during business hours at 213.261.4161

SH65F4B/SH65F4W/SH8F4B/SH8F4W/SH1 OF4B/SH 1 OF4W: Supplied Hardware/Parts

  • l – Pair Marine Grade Tower Speakers
  • l – M6 Allen Hex Tool
  • l – M3 Allen Hex Tool
  • 12 ft – 6 Conductor(2) l 8AWG speaker/(4)22AWG RGB wire (for each speaker enclosure)

Features

MODEL TYPE POWER HANDLING
SH65F4B 6.5″ 2-Way speaker system 150W RMS Power Handling
SH65F4W 6.5″ 2-Way speaker system 150W RMS Power Handling
SH8F4B 8″ 2-Way speaker system 175W RMS Power Handling
SH8F4W 8″ 2-Way speaker system 175W RMS Power Handling
SH10F4B 10″ 2-Way speaker system 200W RMS Power Handling
SH10F4W 10″ 2-Way speaker system 200W RMS Power Handling
SH65F4B & SH65F4W SPECIAL FEATURES
  • 2-Way 6.5″ Pod Speaker System(Pair)
  • 1″ tweeter titanium dome
  • US Manufactured 1.75″ Black High Temperature Glue Coated Voice Coil
  • 150W RMS/300W MAX Power Handing
  • IP65 Marine Grade Compliant, 100% UV Stable
  • Y35 Motor Structure With Max Xmax Suspension
  • Molded injection ASA Grill and Enclosure With Matt Black painted,
  • 316 Stainless Metal Mesh
  • Integrated DIGITAL LED Lighting In Speakers and Enclosure
  • 4″Passive design for bass boost
  • Radial Zip Ring(RZR)Cone for Expanded High Frequency Requency reproduction
  • Flat or Pipe mounting Bracket option
SH8F4B & SH8F4W SPECIAL FEATURES
  • 2-Way 8″ Pod Speaker System(Pair)
  • 1″ tweeter titanium dome
  • US Manufactured 1.75″ Black High Temperature Glue Coated Voice Coil
  • 175W RMS/350W MAX Power Handing
  • IP65 Marine Grade Compliant, 100% UV Stable
  • Y35 Motor Structure With Max Xmax Suspension
  • Molded injection ASA Grill and Enclosure With UV Coating.
  • 316 Stainless Metal Mesh
  • Integrated DIGITAL LED Lighting In Speakers and Enclosure
  • 5″Passive design for bass boost
  • Radial Zip Ring(RZR)Cone for Expanded High Frequency Requency reproduction
  • Flat or Pipe mounting Bracket option
SH10F4B & SH10F4W SPECIAL FEATURES
  • 2-Way 1 0″ Pod Speaker System(Pair)
  • 1″ tweeter titanium dome
  • US Manufactured 2″ Black High Temperature Glue Coated Voice Coil
  • 200W RMS/400W MAX Power Handing
  • IP65 Marine Grade Compliant, 100% UV Stable
  • Y35 Motor Structure With Max Xmax Suspension
  • Molded injection ASA Grill and Enclosure With UV Coating,
  • 316 Stainless Metal Mesh
  • Integrated DIGITAL LED Lighting In Speakers and Enclosure
  • 6″Passive design for bass boost
  • Radial Zip Ring(RZR)Cone for Expanded High Frequency Requency reproduction
  • Flat or Pipe mounting Bracket option

Dimensions

SH65F48/SH65F4W

SH8F4B/SH8F4W

SH10F4B/SH10F4W

Initial Setup

  1. Be sure to carefully read and understand the instructions before attempting to install these speakers.
  2. For safety, disconnect the negative battery terminal from the battery prior to beginning the installation.
  3. For easier assembly, we suggest you have all your tools handy- Drill, Allen set, Crimps, Soldering iron, wire strippers, heat-shri,nk, etc
  4. Use high quality “Water Proof” cohnectors for a reliable installation and to minimize signal or power loss.
  5. Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical winng when working on any vehicle. If installation in a baot, take care or drill through the main hull.
  6. Never run wires near or power (if possible). Running the wires inside the hull area provides the best protection.
  7. Avoid running wires over  or through sharp edges. Use rubber or plastic Groments to protect any wires routed through metal, especially the tower.
  8. Make sure that the mouting clamps are tight before leavingthe dock
  9. Decide early what type of LED lighting you want (if any) and wire accordingly
    (NOTE: if you want”Dancing light” look to the RPMDLED -RF remote controlled LED light box. The easy way to have lighting… YOUR way!)

Instalaltion

MOUNTING

Step 1: Remove tower speakers from the packaging and ALL hardware
Step 2: Find a GOOD location that allows for easy wiring of the speakers (and LED lights) – PLUS does NOT impair you movement around the location.
Step 3: Using the supplied M6 Allen wrench remove the 2 – M6/50mm bolts that hold the clamp tops onto the clamp bottoms of the tower speakers.
Step 4: These speakers are not too heavy but we recommend that you have a friend help you by holding the speaker/enclosure up while you insert and screw down the large M6 bolts.
Or alternatively use a large tie-wrap to “hang” the tower speaker while you insert and screw down the large 5mm bolts.
Step 5: Tighten the M6 clamp bolts down, but DO NOT over tighten as this will -strip the clamps making them useless.

Step 6: If need be,.. rotate the speakers for best dispersion. This is easily done by locating the 3mm Allen set screw on the side of the mounting clamp. Once located release it using the included M3 Allen wrench so that you may rotate the speaker/enclosure to the desired angle. Once there…lock the Allen down.

NOTE:
Blue Loctite is recommended for ALL Allen head bolts/hardware.

Step 7: During the mounting process you should have located the spot to drill your tower bar for the 6 conductor wire (Speaker and RGB lighting wiring) insertion. Or.. NOT (See Tie-wrap solution below)
Step 8: Drill a 3/8″ hole in the pipe and de-burr the hole so there is no sharp edges. It is also recommended to install a rubber grommet in this hole to protect the wire.

Step 9: Slide the wire jacket down thru the hole with grommet and wire. Snake the wire down to the bottom of the tower tube in a location that the wires can be attached to the audio (and lighting) system. Solder or butt connect the speaker wire coming from the tower to the speaker wire to the system.
Then heat-shrink it for added protection from water/mois­ ture.

Wiring

TOWER TUBE  WIRING DETAIL

LED/SPEAKER  WIRING CONFIGURATION

Specifications

Model

| SH65F4B| SH65F4W| SH8F4B| SH8F4W| SH10F4B| SH10F4W
---|---|---|---|---|---|---
Nomina l Diameter – inch (mm)| 6.5
(165)| 6.5
(165)| 8
(203)| 8
(203)|

10
(254)

| 10
(254)

Description

| 2-Way| 2-Way| 2-Way| 2-Way| 2-Way| 2-Way
Nomina l Impedance (Ohms)| 40| 40| 40| 40|

40

| 40

Frequency Response(Hz)

| 70-18 kHz| 70-18 kHz| 55-18 kHz| 55-18 kHz| 50-18 kHz| 50-18 kHz
Voice Coil Diameter – lnch(mm)| 1.75
(44.7)| 1.75
(44.7)| 1.75
(44.7)| 1.75
(44.7)|

2
(50.8)

| 2
(50.8)

Power Handling – Watts (RMS/ Peak)

| 150/300| 150/300| 175/350| 175/350| 200/400| 200/400
Fs – Free Air Resonance (Hz)| 80| 80| 60| 60|

55

| 55

Qts

| 0.828| 0.828| 0.948| 0.948| 0.529| 0.529
Vas- cu. ft. (Liter)| 4.866| 4.866| 13.791| **** 13.791|

**** 41.319

| **** 41.319

Sensitivity (1W/1M)

| 92| 92| 93| 93| 95| 95
Sensit ivity (2.83V/ 1M)| 95| 95| 96| 96|

98

| 98

Mounting Height – inch (mm)

| 9.9
(250.7)| 9.9
(250.7)| 11.6
(44.7)| 11.6
(44.7)| 13.7
(346.8)| 13.7
(346.8)
**** Mounting Diameter -inch (mm)| 6.9
(174.9)| 6.9
(174.9)| 8.6
(219)| 8.6
(219)|

16.6
(270)

| 16.6
(270)

Mounting Length – inch (mm)

| 7.5
(189.7)| 7.5
(189.7)| 8.3
(210.7)| 8.3
(210.7)| 9.4
(239.2)| 9.4
(239.2)
Clamps/Wire| YES| YES| YES| YES|

YES

| YES

We reserve the right to change products and specifications at any time without notice.
Images may or may not include optional equipment.

Warranty

Thank you for purchasing a Cerwin Vega Mobile product and we hope to provide you with countless hours of listening enjoyment.

Please take a brief moment to register your new product. By registering your new product, you will receive benefits such as:

  • Important product notifications that may pertain to your purchase.
  • Confirmation and record of ownership in case of loss or theft.
  • Knowledgeable customer service and technical assistance pertaining to your product.

Register your new product by completely filling out this Product and Warranty Registration card or register online at www.cerwinvegamobile.com.

Registration is voluntary and failure to register will not diminish your limited warranty rights. Limited Warranty (U.S.A.)

Cerwin Vega Mobile warrants all of our amplifiers and speakers to be free of defects in materials and workmanship for a period of one (l) year.

This warranty is non-transferable and applies only to the original purchaser from an authorized Cerwin Vega Mobile dealer. If service is required and necessary under this warranty due to manufacturing defect or malfunction, then Cerwin Vega Mobile will repair and/or replace defective product with eit er new or remanufactured like product at no charge at our discretion.

Damage to product caused by the following will not be covered under this warranty: abuse, accident, misuse, neglect, modifications, repairing attempts, seller/installer misrepresentation.

This warranty does not cover any incidental, consequential, or cosmetic damage due to accidents or normal wear and tear, nor does it cover the cost of removing or reinstallation of the product.

Warranty is void if the product’s serial number has been removed, defaced, and/or tampered with.

Warranty Procedure:
We recommend that you contact your Cerwin Vega Mobile authorized dealer where your original purchase was made to initiate all warranty clmai s. Our authorized dealers can guide you through the warranty procedure to ensure that your claim will be processed in a timely manner. All warranty returns must be accompanied with a proof of purchase (a copy of the original sales receipt) and be shipped freight prepaid to our facility with an RA (Return Authorization) number clearly marked on the outside of the packag e. Direct returns from consumers or non-authorized dealers will be refused if shipped without a valid RA number authorized by Cerwin Vega Mobile beforehand.

INTERNATIONAL
Products purchased outside of the U.S.A. are covered only by that country’s distributor and not by Cerwin Vega Mobile U.S.A.

Please Ship All Warranty Claims With Pre-Authorized RA Number To:
CV&DA Holdings, Inc.
ATTN: Customer Service Department 1225 E. 7th St.
Los Angeles, CA 90021 USA

Please Contact Customer Service for Further Warranty Information:
U.S.A.
Tel: 213-261-416 1 / Fax: 213-947-47 67

3761 South Hill Strteet
Los Angeles 90007, USA
P 213-261/F213-947-4767

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

cerwin vega User Manuals

Related Manuals