VIP VISION Solar Lighting and Power Archives Installation Guide

: October 27, 2023
: VIP VISION

VIP VISION Solar Lighting and Power Archives Installation Guide

Product Information

Included Components

Thank you for purchasing a VIP Vision Solar Surveillance System.
Below is a list of what is included with the standard Solar Surveillance System. Please note that this can vary, depending on the customization options selected. Please refer to the included configuration sheet for specific product details.

Solar Panel

Image|
Panel Model| 120| 180
Panel Type| 120W monocrystalline silicon panel| 180W monocrystalline silicon panel
Conversion Rate| Up to 21% efficiency
Battery| 12.8V/500Wh Lithium Iron Phosphate (LiFePO4) w/ Low Voltage Cutoff| 25.6V/1200Wh Lithium Iron Phosphate (LiFePO4) w/ Low Voltage Cutoff
Dimensions| 1321 x 525 x 161mm| 1496 x 685 x 161mm
Panel Adjustment| -60° ~ 60° tilt adjustable with angle compass
Ingress Protection| IP65
Wind Resistance| Up to 65m/s
Dimensions| Ø50 ~ 60mm
Area Light
Light Module| 50W LED (3030 Philips), 9400lm (180lm/W)| 60W LED (3030 Philips), 11100lm (180lm/W)
Light Characteristics| 145° x 100° (batwing) beam angle / 5700K cool white / 50,000hrs rated lifespan
Motion Detection| Microwave motion sensor, Ø8 ~ 15m range (at 10m height)
Adjustable Settings| Normal & Morning time periods / Brightness on motion / On-time delay / Brightness after delay
Light Adjustment| -30° ~ +30° tilt adjustable LED module
**Camera **
Camera Options| 4.0MP Mini AI PTZ Dome 2.8 ~ 12mm Motorised lens 31.6° ~ 96.9° (4x optical zoom) Pan: 0° ~ 355° / Tilt: 5° ~ 90° IP66 weather resistant IK08 vandal resistant Video analytics (tripwire etc.) Perimeter protection to identify people & vehicles

__****Connectivity **
Inclusions and Optional Accessories| | | |
Solar CCTV Assembly (included) Mounting kit with backing box and triple- clamp pole mount (pole not incl.)| 256GB MicroSD (included) 256GB surveillance grade microSD card for footage recording| 3G/4G LTE Modem Router (option)** LTE connectivity up to 150Mbps speeds 4G: FDD 700/900/1800/2100/2600; TDD

2300Mhz

*SIM card & service charges not included

| 5.8GHz Wireless Links (option) 2 x 5.8GHz wireless antennas 120° beam width, 25dBi gain

Pair configured as network bridge

Optional Mounting Components

Below are optional mounting components; please contact your supplier for more information.

| |
---|---|---
4.5m Hinged Galvanised Pole SLR-POL4.5H Includes 1 x Pole| Unassembled Solar Base

SLR-POLBASE Includes 1 x Base, 4 x Mounting Bolts, 1 x Bolt Template & 1 x Steel Reinforcement Cage On-site assembly required Concrete not included

| Assembled Solar Base

SLR-POLCONC Includes 1 x Base, 4 x Mounting Bolts, 1 x Bolt Template, 1 x Steel Reinforcement Cage & Concrete Assembled off-site

Solar Panel Information

120W/180W Solar Panel with Motion-Sensing Street Light

This solar panel system is fitted with undervoltage protection, which disconnects the load at approximately 10.8V (SLR-B120) or 21.6V (SLR-B180). If you are not receiving any voltage on the output wires, place the panel in direct sunlight for a minimum of one hour and re-test.

The output will be reconnected automatically when battery voltage reaches approximately 11.5V (SLR-B120) or 23.0V (SLR-B180). For more information on panel configuration, refer to Section 4.

The solar panel must be installed in direct sunlight. Shade will negatively impact performance.

This solar panel includes a motion-activated LED light. For more information, refer to Section 4.

Solar Panel Assembly Diagram

Lamp Arm

Lamp Arm

Bird Spikes

Bird Spikes

Accessories

Accessories

#	Component
1	Solar panel
2	LED light
3	Microwave sensor
4	Lamp arm
5	Bird spikes
6	Screws
7	Safety rope
8	T40 Torx

Camera Information

The camera has been pre-installed with a 256GB microSD card and has been preconfigured to record at its maximum mresolution.

The username and password details for the camera can be found on the configuration sheet inside the junction box.
The default username is admin.

To prevent unauthorised access, ensure you change the admin password before completing installation.

Default Camera Configuration

Main Stream

Stream Type| General
Encode Type| H.265
Resolution| Camera max
FPS| 15
Encoding Method| Constant Bit Rate
Quality| 6 (Best)
Bit Rate| 1536-8192Kbps
I Frame Interval| 30
Sub Stream

Installation

Installation Prerequisites

It is strongly recommend to have a minimum of two people performing installation of the solar panel, base, and pole.

Required Install Tools: 5mm & 6mm Allen keys for junction box (included), T40 torx key for solar panel (included), 10mm Allen key, 20mm hole saw, battery drill, phillips screwdriver, flat head screwdriver, lifting equipment, padlock with key, large adjustable spanner. A laptop with RJ45 network interface is strongly recommended for camera setup.

For more information and videos regarding base and pole installation, please visit the below website.

https://help.c5k.info/solar-installation

Installing the Optional Base

Warning: The pre-assembled base weighs approximately 500kg. Specialist lifting equipment is required to move the base. Care must be taken to prevent injury when moving the base.

Pre-Assembled Base:

Locate a hard level surface to install the base, ensure that there is easy access for the lifting equipment that will be required, and that it is free from objects that will shade the solar panel, such as trees or buildings.
Using lifting equipment, position the base on the ground.

Un-Assembled Base:

Locate a hard level surface to install the base, ensure that it is free from objects that will shade the solar panel, such as trees or buildings.
Install the reinforcing cage inside the base. Install a washer and nut on each threaded rod on the top side of the base, to secure the cage. (Fig. 2.2a)
Place the base open side up, on top of a solid object such as concrete besser blocks. (Fig. 2.2b)
Mix approx 480kg of concrete, and pour into base. Ensure the concrete that is exposed is level with the top of the base, otherwise the base will not sit level on the ground. (Fig. 2.2c)
Allow a minimum of 7 days for the concrete to cure, this can take longer depending on weather conditions.
Once the concrete has cured, use suitable lifting equipment to turn the base over

Installing the Optional Tilt Pole

Warning: The tilt pole weighs approximately 100kg. Care must be taken to prevent injury when installing the pole.

Attach a lifting sling to the hinged part of the pole.
Unhinge the pole and position the pole base over the 4 threaded studs.

Mounting pole onto concrete base

Pole fixed onto on concrete base

Install the included washers and nuts. Ensure the nuts are fastened securely.
Refer to Section 2.4 – 2.8 to mount the camera and solar panel to the pole. After the steps have been followed continue with the steps below.
Using lifting equipment, raise the pole.
Once the pole is vertical, secure it into position with the included bolt and nut.
Using a padlock, lock the pole.
Re-tighten the nuts on the pole base.

Mounting the Solar Panel to the Pole

Solar panel power cable hole location Installed grub
screws

Caution: Solar panel must be placed so it is in direct sunlight all day.
Any shading will greatly reduce the solar panel’s performance.

Drill an 20mm hole in the pole (minimum 15cm down from the top of the pole) on the same side that the camera will be mounted.
This is for the solar panel cable and plug to run through. The position of the hole will vary depending on what position on the pole the camera is to be mounted. If using the optional tilt pole, this hole will be predrilled,
Feed the power cable and plug connected to your solar panel through the hole.
Place the solar panel bracket on top of the pole, pointing north.
Note: If you need to cover a different area with the light beam, keep the panel flat after repositioning.
Securely fasten the included grub screws to the bracket. Tighten the locking bolts to prevent the grub screws from loosening. (Fig. 2.4b)
Note: For poles greater than 4m in height, tapered poles are preferable for camera stability and pole strength.

Adjusting the Solar Panel Angle

To ensure your solar panel absorbs as much light as possible, it’s important to adjust the solar panel angle.

For Australia and all locations in the southern hemisphere, the lower edge of the solar panel must point north. Locations in the northern hemisphere must have the lower edge of the panel pointing south.

The angle of tilt should ideally be 10° North. If you are using the light on the solar panel, keep in mind which direction this will face, and adjust accordingly

Adjusting the Solar Panel Angle

How to adjust tilt angle:

Use a flat head screwdriver to remove the bracket cover (Fig. 2.5a).

Fig. 2.5a
Solar panel angle screw cover

Once the cover is removed, use a 10mm Allen key to loosen the panel adjustment bolt and tilt the panel to the required angle with the LED light at the high side. (Fig. 2.5b).

Fig. 2.5b
Solar panel angle adjustment screw

Tighten the bolt after adjusting the angle to secure the solar panel in place.
Replace the cover.

Camera Mounting & Wiring

Open the junction box by loosening the 4 screws, and loosen the 2 screws (Fig. 2.6a), holding on the junction box mounting plate and pole bracket (Fig. 2.6b).
Mount the junction box mounting plate and pole bracket onto the pole using 3 included band clamps (Fig. 2.6c).

Note: The 3 included band clamps are 65-89mm for poles 50-60mm in diameter. If installing on a thicker pole (eg. 80- 150mm), larger band clamps will be required.

Reinstall the junction box to the junction box mounting plate, and securely fasten the 2 screws. Leave the junctionbox open.
If using a 4G solar kit, insert an active Micro SIM card into the SIM card slot in the modem. (Fig 2.7a) If using a Wi-Fi solar kit, mount the wireless antenna to the pole with the included mounting hardware, and attach the ethernet cable. (Fig 2.7b)
Attach the waterproof plug from the solar panel side, to the camera side.
Close the junction box and securely fasten the 4 bolts (Fig. 2.7c).

Reconnect Battery

The Solar Light is shipped with the battery disconnected from the system.

To activate the Solar Light, this battery must first be reconnected. To reconnect:

Remove the “Battery Disconnected” sticker. (Fig 2.8a)
Find the two cables labeled “Battery”. (Fig 2.8b)
Taking note of the cable key, connect the two cables. (Fig 2.8c)
Twist the waterproof locking connector until tight. (Fig 2.8d)
Install the solar panel connection cover, included in the solar panel accessory bag. (Fig 2.8e)

Once the battery is connected, a red LED will flash slowly inside the black sensor on the solar panel. If the battery is connected correctly and this does not occur, this likely indicates low battery voltage – place the system in direct sunlight for at least 1 hour to charge before continuing.

Wi-Fi (Applies to SLR-B120/180-4W Only)

Connect using WiFi

This section covers how to set up the Access Point side of WiFi network for your WiFi Solar Surveillance Kit. Note: The station side of the wireless bridge should already be mounted under the solar panel.

Ensure the Ethernet cable is connected between the camera and the wireless bridge (station), as per section 2.6.
Mount the other side of the wireless bridge (access point) on the building, facing towards the station on the solar panel.
The access point can be powered by connecting the AP’s network port to the included PoE injector, then connect the injector to a network switch and power supply.
(Optional) Connect the network switch to an NVR (The camera includes a microSD card for edge recording).
(Optional) Connect the network switch to a router, to be able to remotely access the NVR.

Camera Remote Access

QR Code Remote Access Setup (4G)

Internet access is required for remote access setup.

Install the free mobile application (DMSS) from the App Store for iOS or Play Store for Android.
Open the DMSS app you have installed on your device and select the “+” icon
Select SN/Scan. (Fig. 4.1a)
Use your mobile device to scan the QR code (refer to configuration sheet inside junction box). (Fig. 4.1b) Make sure the app is permitted to access your phone’s camera. Alternatively, select Manually Enter SN and enter the serial number of the camera.
Select Wired Camera. (Fig 4.1c)
Enter a Device Name for the camera. This name is for reference only.
Enter the default username admin and password (refer to configuration sheet inside junction box). For extra security, be sure to change these details before completing installation.
Select Save (Fig. 4.1d), if the details are correct, the camera will display a live image

Adjusting Stream Settings

You can choose between using Main or Sub stream when Live Viewing on the mobile application. (Fig. 3.2d) Main displays a higher quality stream but uses up more data and can take longer to load, while Sub consumes less data and bandwidth but has lower image quality. When using Playback, ensure that Playback is set to Main. If set to Extra, the screen will be black. This is because the camera has been preset to only record the Main stream to the microSD card.

Open the application and go the home screen and select the 3 dots “…” next to the device. (Fig 4.2a)
Select Device Details (Fig 4.2b), then Stream Settings. (Fig 4.2c)
Adjust the stream settings, Set Live to Sub, and Playback to Main. (Fig 4.2d)

Additional Camera Configuration

For more information regarding camera setup and use, please visit:

https://help.c5k.info/solar-camera-setup

Solar Panel, Sensor & Light Configuration

Solar Sensor Light Introduction

This section covers how to set up the motion-activated 50W (SLR-B120) or 60W (SLR-B180) LED light on the solar panel. Our example will show you how to configure your solar panel & light with the remote control, showing you how to configure the light to activate after motion is detected at night.

Warning: Modification to the LED light and sensor default values may increase power consumption, affect light uptime and more.

Incorrectly editing settings can permanently damage the solar panel, battery and/or LED light. Performing changes to contrary to those in this guide may cause damage to the panel not covered under warranty.

All configuration of the solar panel & LED street light is performed with the included infrared remote. The remote interacts with the panel’s infrared receiver to control settings (the dark circle on the underside of the panel). Any modification to settings is best performed at night, as infrared interference during the day may reduce remote range.

The remote control allows you to adjust solar panel, battery & sensor settings and then transmit them to apply the configuration to the solar system. See initial menu options and button functions below:

Startup Menu Options

System Info| Diagnostic tool to check performance of solar system including uptime, battery & panel statistics.
---|---
Sys Config| Configuration interface where new settings are set & transmitted to the solar system.
Read Data| Current settings applied to the solar system.
Local| Language and device name settings.

| Power| Press to power on. Press and hold for 2 seconds, then release to power off the remote control.
---|---|---
| Scroll Up| Press to scroll up.
| Sending Key| Press to transmit parameters to the control board.
| Signal On| Press and hold to enable the LED light control.
| Enter Key| Press to select item or confirm changes.
| Signal Off| Press and hold to disable the LED light control.
| Search Key| Not used.
| Down Key| Press to scroll down.
| Back| Press to select item or confirm changes.

Settings Detail

Each Solar Light has default factory settings for light configuration and battery configuration. Below are the functions of each setting in the SysConfig menu and the solar system default settings . Before adjusting solar panel and light settings, familiarise yourself with the setting definitions below.

Note: Modification to the LED light and sensor will increase power consumption and reduce battery power available for the system.

Incorrectly editing settings can permanently damage the solar panel, battery and/or LED light. Only edit power settings exactly as outlined in this guide. Please contact your place of purchase for more information.

Name| Remote Title| Description| Settings| Default Settings
---|---|---|---|---
Battery Type| Bat Type| Type of battery installed in the solar panel| Li_Po / Lead_acid| Must use Li_Po for LiFePO4 battery,
DO NOT change this parameter
Boost Charge| BoostCharge| Battery overcharge voltage. To protect the battery from overcharging, the battery stops charging when it is above this voltage.| 10.80V ~ 32.80V| SLR-B120: 14.4V SLR-B180: 28.8V
Warning: Changing this setting may damage the solar system.
Voltage Low| Voltage Low| Battery cut-off voltage. When the battery voltage falls below this value, output will be disabled.| 8.10V ~ 24.00V| SLR-B120: 10.5V SLR-B180: 21.0V
Warning: Changing this setting may damage the solar system.
Recover Voltage| Recover Vol| Minimum voltage for the battery to start. Battery output is enabled or resumed from cut-off when battery voltage is above this value.| 9.00V ~ 25.00V| SLR-B120: 12.0V SLR-B180: 24.0V
Warning: Changing this setting may damage the solar system.
Power Saving| PowerSaving| When turned on, the battery will adjust power output automatically to save energy.| On / Off| All Models: Off
Turn-On Photovoltaic Voltage| TurnOnPVVol| The solar panel acts as an ambient light sensor. Once the solar panel voltage drops below the ‘Turn-on PV Voltage’, the light turns on.| 4.0V ~ 12.0V| All Models: 5.0V
Output Current| Output Cur| Set the constant current output level.| 150mA ~ 4000mA| All Models: 300mA
Drive Mode| DriveMode| Time (Time Control): Set up to 5 periods of up to 9 hours each, controls light activation. Time intervals begin after TurnOnPVVol threshold is reached i.e: the sun has set. Light brightness in each period is set by Light Ratio.
Sense (Movement Sensor): Adds motion detection on top of 5 time periods. The light abides by Time (Time Control) , but dims to Idle Ratio and brightens to Light Ratio based on movement detection.| Time (Time Control) or Sense (Movement Sensor)| All Models:
First Period: 2 Hours Second Period : 3 Hours Third Period: 7 Hours Fourth & Fifth Periods: Not Set
Light Delay| LightDelay| Countdown timer after last detection motion where light output stays at Light Ratio setting before switching to Idle Ratio setting.| 0s ~ 120s| All Models: 30 seconds.
First, Second, Third, Fourth, Fifth Time| User-programmable light on/off schedule. Maximum 9 hours for each setting.| 0.00hrs ~ 9.00hrs| Sets time periods, see Drive Mode for default settings.
Light Ratio| LightRatio| Set light output (%) for Time (Time Control) or when movement is detected in Sense (Movement Sensor) mode.| 0% ~ 100%| All Models: First Period: 100% Second Period : 60% Third Period: 30% Fourth & Fifth Periods: Not Set
Idle Ratio| Idle Ratio| Set light output (%) in Sense (Movement Sensor) mode after last detected movement and after Light Delay elapses.| 0% ~ 100%| All Models: First Period: 30%
Second Period : 20%
Third Period: 10%
Fourth & Fifth Periods: Not Set
Morning Light| MorningLight| Overrides TurnOnPVVol , making the light stay on during the day, as per the Drive Mode Time Control parameters.| On / Off| All Models: Off

Change LED Light Settings

Point the remote control at the solar panel’s black sensor and scroll to the SysConfig (System Configure) and press (Enter) to enter the system configuration menu.
- Use and to scroll.
- Press Enter to begin editing values. The value will be shown in reverse colour.
- Use and to change the value.
- Press Enter again to confirm.
  Note: The remote will power off automatically if no key is pressed for 3 minutes.
  Five periods of time can be set to turn on the solar panel LED light. These periods can be set with a min. of 0 and max. of 9 hours. (9 hours by default – refer to 5.2 Default Light Ratio & Period Settings)
Point the remote control at the solar panel’s black sensor and press Sending Key to update the solar panel with your new configuration. If you hear a long beep, the configuration settings are transmitted successfully.

Disable LED Light

To disable the LED light, simply change the Drive Mode from Move Sensor to Time Ctrl. Then set each time period to 0 hours, and each light ratio to 10%.

Check Solar Panel Status

To check the solar panel’s current state, scroll to the System Info menu and press Enter. This will show info such as photovoltaic voltage, battery voltage, output voltage, current and power, temperature and total operating time in minutes and more.

Name	Remote Title	Description
Solar Panel Status	System	On connecting to the panel, the Solar Panel

Status can be in 3 states.
CurrentDrive: when the Solar Light is on
PWM Charge: when the Solar Panel is charging
Shutdown: when the remote hasn’t connected or the system is below Low Voltage Cut-Off.
Photovoltaic Voltage| PV Voltage| Solar panel voltage as measured by the charge controller input.
Battery Voltage| Bat Voltage| Battery voltage as measured by the charge controller output.
Output Voltage| Output Vol| Voltage being supplied to the LED light.
Output Current| Output Cur| Current being supplied to the LED light.
Output Power| Output Pow| Power being supplied to the LED light.
Internal Temperature| Inter Temp| Temperature inside the Solar Light.
Full Charge Count| FullChargeCnt| Count of how many times the panel has reached the Charge-Stop Voltage (fully charged).
Voltage Low Count| VoltageLowCnt| Count of how many times the panel has reached the Low Voltage Cut-Off (fully discharged).
Total Uptime| Runing| Total running uptime of the Solar Light, measured in hours & minutes.

Lock/Unlock the Remote Control

After setup has been completed, you can lock the remote control to prevent settings from being accidentally changed, or changed by somebody else.

To Lock/Unlock the remote control, press the Search , Enter and Back buttons together.
When you hear a long single beep, the remote is now locked. Repeat these steps to unlock the remote.

Troubleshooting

Problem	Troubleshooting
Cannot connect to camera remotely

Ensure a SIM card is installed that is activated, and has data remaining on it. (4G Models)
Ensure solar panel is charged, and there is power to the modem and cam- era

Camera only recording during day- light hours|