eCLer ARQISi Series Cabinat Loud Speaker Architectural Loudspeaker Cabinets User Manual

eCLer ARQISi Series Cabinat Loud Speaker Architectural Loudspeaker

Cabinets

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “ dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING (If applicable):

• The terminals marked with symbol of “ may be of sufficient magnitude to constitute a risk of electric shock. The external wiring connected to the terminals requires installation by an instructed person or the use of ready-made leads or cords.
• To prevent fire or shock hazard, do not expose this equipment to rain or moisture.
• An apparatus with Class I construction shall be connected to a mains socket-outlet with a protective earthing connection.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Unplug the apparatus during lightening sorts or when unused for long periods of time.
13. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
14. Disconnecting from mains: When switching off the POWER switch, all the functions and light indicators of the unit will be stopped, but fully disconnecting the device from mains is done by unplugging the power cable from the mains input socket. For this reason, it always shall remain easily accessible.
15. Equipment is connected to a socket outlet with earthing connection by means of a power cord.
16. The marking information is located at the bottom of the unit.
17. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

WARNING: This product must not be discarded, under any circumstance, as unsorted urban waste. Take to the nearest electrical and electronic waste treatment centre.

NEEC AUDIO BARCELONA, S.L. accepts no liability for any damage that may be caused to people, animal or objects due to failure to comply with the warnings above.

IMPORTANT NOTE
Thank you for choosing our Ecler ARQISi Cabinet Loudspeakers!
It is VERY IMPORTANT to carefully read this manual and to fully understand its contents before any connection in order to maximize your use and get the best performance from this equipment.
To ensure optimal operation of this device, we strongly recommend that its maintenance be carried out by our authorised Technical Services.
Ecler ARQISi comes with a 3-year warranty.

INTRODUCTION

Based on studying installers and interior design and system integration professionals as well as on a permanent contact with them, the ARQISi line of speakers is designed for fixed installation, especially in environments in need of a compact speaker offering high output, easy installation, long-term reliability and excellent sound quality.

Evolution of the acclaimed ARQIS series, the ARQISi loudspeakers are fine- tuned to balance the sound across the entire range, improve frequency response, increase power (ARQIS110i, ARQIS112i), and add a new subwoofer model (ARQISSB12i). The 105, 106 and 108 models include a new wall bracket VEASY, VESA mounting standard compatible, easy to install and with vertical and horizontal adjustment. The entire range incorporates a square logo that can be rotated at 90° angles without the need for tools.

The ARQISi series is ideal for shopping centres, sports centres, theatres/auditoriums, conference rooms, audio-visual presentations, corporate rooms, perimeter reinforcement in clubs, cafés, restaurants and theme parks among other solutions.

MODELS

ARQIS105i

• Full range, 2-way architectural loudspeaker
• 70 WRMS @ 8 Ω
• 5,25″ woofer
• 1″ tweeter
• Double INPUT/STACK connector, Euroblock type, with security attachment screws to avoid accidental disconnection
• VEASY Wall bracket included, allowing for pan & tilt adjustment, employing a single screw for fastening. Robust, quick and easy to install, including jumps and markings for repeating speaker orientation.
• Available in black (RAL9005) or white (RAL9003) finish

ARQIS106i

• Full range, 2-way architectural loudspeaker
• 120 WRMS @ 8 Ω
• 6,5″ woofer
• 1″ compression driver (rotable)
• Double INPUT/STACK connector, Euroblock type, with security attachment screws to avoid accidental disconnection
• VEASY Wall bracket included, allowing for pan & tilt adjustment, employing a single screw for fastening. Robust, quick and easy to install, including jumps and markings for repeating speaker orientation.
• Metal safety sling included, to avoid drops in case of accidental detachment from the wall surface
• Available in black (RAL9005) or white (RAL9003) finish

ARQIS108i

• Full range, 2-way architectural loudspeaker
• 150 WRMS @ 8 Ω
• 8″ woofer
• 1″ compression driver (rotable)
• Double INPUT/STACK connector, Euroblock + Speakon© type, with security attachment screws to avoid accidental disconnection
• VEASY Wall bracket included, allowing for pan & tilt adjustment, employing a single screw for fastening. Robust, quick and easy to install, including jumps and markings for repeating speaker orientation.
• U-bracket wall-mount accessory compatible, ARQ108UB (not included)
• Metal safety sling included, to avoid drops in case of accidental detachment from the wall surface
• Available in black (RAL9005) or white (RAL9003) finish

ARQIS205i

• Full range, 2-way architectural loudspeaker
• 140 WRMS @ 8 Ω
• 2 x 5,25″ woofer
• 1″ compression driver (rotable)
• Double INPUT/STACK connector, Euroblock + Speakon© type, with security attachment screws to avoid accidental disconnection
• U-bracket wall-mount included, allowing for tilt adjustment
• 4x M6 & 12 x M8 cabinet flying points
• Metal safety sling included, to avoid drops in case of accidental detachment from the wall surface
• Available in black (RAL9005) or white (RAL9003) finish

ARQIS208i

• Full range, 2-way architectural loudspeaker
• 300 WRMS @ 8 Ω
• 2 x 8″ woofer
• 1″ compression driver (rotable)
• Double INPUT/STACK connector, Euroblock + Speakon© type, with security attachment screws to avoid accidental disconnection
• U-bracket wall-mount included, allowing for tilt adjustment
• 4x M6 & 12 x M8 cabinet flying points
• Metal safety sling included, to avoid drops in case of accidental detachment from the wall surface
• Available in black (RAL9005) or white (RAL9003) finish

ARQIS110i

• Full range, 2-way architectural loudspeaker
• 300 WRMS @ 8 Ω
• 10” woofer
• 1″ compression driver (rotable)
• Double INPUT/STACK connector, Euroblock + Speakon© type, with security attachment screws to avoid accidental disconnection
• 35 mm mount socket, compatible with SR12 wall bracket (not included) & TRIPO1 floor stand (not included)
• U-bracket wall-mount accessory compatible, ARQ110UB (not included)
• 12 x M8 cabinet flying points.
• Available in black (RAL9005) or white (RAL9003) finish

ARQIS112i

• Full range, 2-way architectural loudspeaker
• 500 WRMS @ 8 Ω
• 1 x 12″ woofer
• 1″ compression driver (rotable)
• Double INPUT/STACK connector, Euroblock + Speakon© type, with security attachment screws to avoid accidental disconnection
• 35 mm mount socket, compatible with SR12 wall bracket (not included) & TRIPO1 floor stand (not included)
• U-bracket wall-mount accessory compatible, ARQ112UB (not included)
• 12 x M8 cabinet flying points.
• Available in black (RAL9005) or white (RAL9003) finish

ARQISSB6Ti

• 6,5″ subwoofer + 6,5″ pasive radiator
• Ready for 70/100V installations: power selector 60/120W & 8 ohm
• Euroblock connector and spring loaded input terminals
• LPF cut-off frequency selection: OFF/ 120Hz / 150Hz
• Wall-mount hardware included
• Available in black (RAL9005) or white (RAL9003) finish

ARQISSB10i

• 1-way surface-mount subwoofer
• 150 WRMS @ 8 ohm
• 10″ woofer
• Euroblock connector and spring loaded input terminals
• LPF cut-off frequency selection: OFF/ 120Hz / 150Hz
• Wall-mount hardware included
• 12 x M8 cabinet flying points
• Available in black (RAL9005) or white (RAL9003) finish

ARQISSB12i

• 1-way surface-mount subwoofer
• 300 WRMS @ 8 ohm
• 10″ woofer
• Euroblock connector and spring loaded input terminals
• LPF cut-off frequency selection: OFF/ 120Hz / 150Hz
• Wall-mount hardware included
• 12 x M8 cabinet flying points
• Available in black (RAL9005) or white (RAL9003) finish

ARQISSB15i

• 1-way architectural subwoofer
• 600 WRMS @ 8 Ω
• 15″ woofer
• Double INPUT/STACK connector, Speakon© type
• 35 mm top-hat mount socket, for pole mount combinations with ARQIS10, ARQIS12, etc.
• 12 x M8 cabinet flying points.
• Available in black (RAL9005) finish

CONNECTIONS

The connection cables which connect the amplifiers output and the speaker should be of good quality, have sufficient conductor area and be as short as possible. The latter fact is especially important when the distance is long and the load impedance low (4-8 Ω). A cross-section of at least 2.5mm2 is recommended for distances up to 10m; 4 or 6mm2 for longer distances. Following formula gives the required section, assuming 4% losses:

Always respect the polarity. All models have an Euroblock connector, and a second connector (Euroblock or Speakon®, depending on model), thereby facilitating the parallel connection of speakers.

ARQISSB6Ti
ARQISSB6Ti supports high or low impedance operation. In this matter, it has a 3-position switch on its rear panel that allows to select its working mode.
The 8Ω/120W position corresponds to low impedance operation at a maximum power of 120W. The 2 positions of the power selector switch for 70/100V line will allow you to set the maximum power at which each unit will work (60/120W @ 100V | 30/60W @ 70W) .

Note: The loudspeaker distribution along a 70/100V line historically arises from the technical requirement to mix loudspeakers of different impedances and/or powers on the same amplification line or channel, but without any need to worry about the total impedance of the full assembly. Moreover, this solution enables long cable runs with significantly smaller sections that those usually employed in low-impedance installations, but with minimum power losses.

WARNING! If the system is accidentally connected with the switch in the 100 V/60 W position to a low-impedance amplifier, no damage will be caused to the loudspeaker, but its performance will be well below its specifications. If the loudspeaker is accidentally connected to a 70 V/100 V network, in the 8 Ω position, it will be seriously damaged.

EQ SETTINGS
Download the Ecler ARQISi EQ Settings file for ARQIS105i, ARQIS106i, ARQIS108i, ARQIS110i, ARQIS112i, ARQIS205i and ARQIS208i, ready to import in EclerNet Manager software.

RECOMMENDED AMPLIFIER

Following table shows the output power of the amplifier adequate to each acoustic system:

• ARQIS105i: 140W RMS
• ARQIS106i: 240W RMS
• ARQIS108i: 300W RMS
• ARQIS205i: 280W RMS
• ARQIS208i: 600W RMS
• ARQIS110i: 600W RMS
• ARQIS112i: 1000W RMS
• ARQISSB6Ti: 240WRMS @ 8Ω
• ARQISSB10i: 300W RMS
• ARQISSB12i: 600W RMS
• ARQISSB15i: 1200W RMS

POSITIONING

Consider following general rules:
Place the speakers on a solid and firm surface. Subwoofers placed directly and horizontally on the ground have a higher output than hanged or directly on the floor, but vertically. No obstacles should stand between the enclosures and the audience. The high frequencies are very directive compared to the low frequencies, so that any obstacle will impair their response. In case large audiences must be addressed, a better long distance sound propagation will be achieved if the enclosures are flown high enough.

Download all EASE files by clicking on the image:

INSTALLATION

In the ARQISi series, the best way to install the enclosure was studied for each model. Each model from the ARQIS range is supplied with the optimal installation system. The models ARQIS106i, ARQIS108i, ARQIS205i, ARQIS208i, ARQIS110i, ARQIS112i can be installed both horizontally and vertically thanks to the included accessories and the 1″ rotable compression driver.

ARQIS205 / ARQIS208 / ARQIS110 / ARQIS 112 / ARQISSB10 / ARQISSB15 also have built-in M8 rigging points for suspension from a compatible structure or “truss” using steel cables.

IMPORTANT NOTE: The equipment must in no case be suspended using its carrying handles (if any); use the appropriate accessories for each application. Whenever a ceiling/wall mounting bracket is used, it is mandatory to add a redundant safety system. Use wire ropes, slings or chains of the appropriate diameter to prevent the fall of the speaker in case the main mounting system is pulled out.

TECHNICAL SPECIFICATIONS

130°x130° (HxV)
Power handling| 70W RMS / 280W Peak| 120W RMS  / 480W Peak        150W RMS / 600W Peak
Sensitivity3| 89dB (1W/ 1m)| 88dB (1W/ 1m)                        90dB (1W/ 1m)
Maximum SPL4                                    107dB continuous / 109dB continuous /                112dB continuous /

113dB peak                            115dB peak 118dB peak

Recommended|  |
amplifier| 140W RMS| 240W RMS| 300W RMS
Ways| 2-Way| 2-Way| 2-Way
Low frequency driver| 5,25″ woofer| 6″ woofer| 8″ woofer
High frecuency driver                          1″ tweeter 1″ Compression driver            1″ Compression driver

(rotable)                                 (rotable)

Connection type                            2 x Euroblock 2 x Euroblock                     1 x Euroblock & 1x

SPEAKON

Installation options| surface, WALL,desktop| surface, WALL,desktop| surface, WALL,desktop
Environmental| IP31| IP31| IP31
Enclosure material| MDF| MDF| MDF
Grille material| Steel| Steel| Steel
Grille fixing system| screw fixation| screw fixation| screw fixation
Flying points| 4 x M 6| 8 x M 6| 6 x M 6 & 2 x M 8

1. 10dB below the sound pressure level at specified sensitivity
2. 6dB below the sound pressure level than that at the direction of maximum level, Max. angle between 1 kHz and 4 kHz.
3. Measured on-axis, far field and referenced to 1 meter by inverse square law. Average from 100 Hz to 10 kHz.
4. Calculated from sensitivity and power handling specifications, exclusive of power compression

Maximum SPL4                                           111dB continuous / 117dB                 119dB RMS / 125dB peak

peak

1. 10dB below the sound pressure level at specified sensitivity
2. 6dB below the sound pressure level than that at the direction of maximum level, Max. angle between 1 kHz and 4 kHz.
3. Measured on-axis, far field and referenced to 1 meter by inverse square law. Average from 20 Hz to 20 kHz.
4. Calculated from sensitivity and power handling specifications, exclusive of power compression

INSTALLATION DIAGRAMS

Mounting the VEASY wall bracket (ARQIS105i, ARQIS106I, ARQIS108i)

Example of horizontal and vertical installation using the included flying points or the U-bracket (included in 205i, 208i and SB6Ti models, optional for 108i, 110i and 112i models),

CONTENTS OF THE PACKAGING

ARQIS105i

• 1 x ARQIS105i loudspeaker
• 1 x VEASY wall bracket with vertical and horizontal adjustment (VESA compatible)
• 1 x Allen key 3mm
• 1 x Allen key 4mm
• 1 x Allen key 6mm
• 2x Euroblock
• Quick user guide
• Warranty card

ARQIS106i

• 1 x ARQIS106i loudspeaker
• 1 x VEASY wall bracket with vertical and horizontal adjustment (VESA compatible)
• 1 x Allen key 3mm
• 1 x Allen key 4mm
• 1 x Allen key 6mm
• 2x Euroblock
• Quick user guide
• Warranty card

ARQIS108i

• 1 x ARQIS108i loudspeaker
• 1 x VEASY wall bracket with vertical and horizontal adjustment (VESA compatible)
• 1 x Allen key 3mm
• 1 x Allen key 4mm
• 1 x Allen key 6mm
• 2x Euroblock
• Quick user guide
• Warranty card

ARQIS205i

• 1 x ARQIS205i loudspeaker
• 1 x U-shaped wall/ceiling bracket
• 1 x metal safety handle
• 1 x Allen key 5mm
• 1 x Allen key 6mm
• 2 x screws
• 2 x washers
• 2 x rubber washers
• 2 x plastic trims
• 1 x Euroblock
• 1 x Speakon
• Quick user guide
• Warranty card

ARQIS208i

• 1 x ARQIS208i loudspeaker
• 1 x U-shaped wall/ceiling bracket
• Metal security handle
• 1 x Allen key 5mm
• 1 x Allen key 6mm
• 2 x screws
• 2 x washers
• 2 x rubber washers
• 2 x plastic trims
• 1 x Euroblock
• 1 x Speakon
• Quick user guide
• Warranty card

ARQIS110i

• 1 x ARQIS110i loudspeaker
• 4 x screws
• 4 x rubber feet
• 1 x Euroblock
• Quick user guide
• Warranty card

ARQIS112i

• 1 x ARQIS112i loudspeaker
• 4 x screws
• 4 x rubber feet
• 1 x Euroblock
• Quick user guide
• Warranty card

ARQISSB6Ti

• 1 x ARQISSB6Ti loudspeaker
• 1 x U-shaped wall/ceiling bracket
• 1 x metal safety handle
• 1 x Allen key 5mm
• 1 x Allen key 6mm
• 2 x screws
• 2 x washers
• 2 x rubber washers
• 2 x plastic trims
• 1 x Euroblock
• 1 x Speakon
• Quick user guide
• Warranty card

ARQISSB10i

• 1 x ARQISSB10i loudspeaker
• 1 x wall mounting bracket
• 4 x screws
• 4 x rubber feet
• 1 x Euroblock
• Quick user guide
• Warranty card

ARQISSB12i

• 1 x ARQISSB12i loudspeaker
• 1 x Speakon
• 4 x rubber feet
• Quick user guide
• Warranty card

ARQISSB15i

• 1 x ARQISSB15i loudspeaker
• 1 x Speakon
• 4 x rubber feet
• Quick user guide
• Warranty card

All product characteristics are subject to variation due to production tolerances. NEEC AUDIO BARCELONA S.L. reserves the right to make changes or improvements in the design or
manufacturing that may affect these product specifications.

For technical queries contact your supplier, distributor or complete the contact form on our website, in Support / Technical requests.
Motors, 166‐168 08038 Barcelona ‐ Spain ‐ (+34) 932238403 | information@ecler.com | www.ecler.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>