PENTON TSXDIAPOT Bluetooth Headset User Manual
- June 6, 2024
- PENTON
Table of Contents
TSXDIAPOT Bluetooth Headset
User Manual
First time to use Bluetooth pairing
1. Before using, please take off
the film on earbuds and put it into the charging case until the red LED is
on.| 2. Take earbuds from charging case and blue LED flash 3 times| 3. After
pairing, the LEDs on the left earbud flash and the Blue LED on the right
earbud flash.| 4. Turn on the Bluetooth function
of the phone and choose to connect earbuds| 5. Start to use
---|---|---|---|---
| | ![PENTON TSXDIAPOT Bluetooth Headset
- Bluetooth pairing 3](https://manuals.plus/wp-content/uploads/2022/02/PENTON- TSXDIAPOT-Bluetooth-Headset-Bluetooth-pairing-3-300x187.jpg)| |
FACTORY RESET
If you can’t connect both earbuds, initialize the earbuds as follows.
- Delete “HEIMDEX TSX 5.2” from the cellphone’s Bluetooth list.
- Take both earbuds out of the charging case.
- Power off by touching and holding the power button of both earbuds for about 6 seconds.
- Touch and hold both earbud power buttons at the same time for about 10 seconds. The red LED blinks 3 times and the power off. (Earphone factory reset is successful)
- Put both earbuds back to the cradle and take them out and pair them again.
- Register and use “HEIMDEX TSX 5.2” in the mobile phone’s Bluetooth list.
※ Search for “TSX 5.2 Factory rest” on YouTube.
Auto Power on/off (Auto Bluetooth pairing from 2nd time)
Type 1. Manual Power on
Type 2: Pick up one or two earbuds for auto-pairing
Register and use “HEIMDEX TSX 5.2” in the mobile phone’s Bluetooth list.
Type 1 · Manual Power off
Type 2: Put earbuds into charging box for auto power off
Type 3: Disconnect Bluetooth connection of the phone. It will be automatically
powered off after 3 mins.
Please take and put earbuds in the case again, if it is still power-on.
Touch Control
Charging
Earbuds charging
When the low battery, there is an indication of voice from earbuds Besides,
the LEDs have red flashing every 10 seconds.
When full charging, the light on earbuds is off
Box charging
CAUTION ON CHARGE
When the low battery, there is an indication voice from earbuds Besides, When
full charging, the LEDs have red flashing every 10 seconds.
light on earbuds is off
5V 1A or less charger is recommended.
5V 2A Charger & 9V 1.67A/ 5V 2A Mixed charger is available.
(However, Fast chargers can cause product failure.)
※ Never use fast charger for vehicle
Please check and charge the battery frequently, to get better performance of the battery
FCC STATEMENT
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1 )This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>