Sricam 20211012 PoE NVR Kit User Guide

: June 6, 2024
: Sricam

Table of Contents

Install PoE NVR
Connection PoE NVR
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

PoE NVR Kit
Quick Operation Guide
V1.0 20211012

Thank you for purchasing our products, if you have any questions or needs, please contact us.
Interface:

Install PoE NVR

Note: A. Disconnect the power from the NVR before installing a hard disk drive (HDD). B. The maximum of hard disk capacity supported is 8TB (Terabytes). C. For PoE power supply, please use a Category 5 network cable or above D. Support all Onvif cameras, connect other brands cameras, please confirm whether the onvif function is supported

Connection PoE NVR

Connect the mouse to the USB port of the NVR.
Connect to the monitor via an HDMI / VGA cable.
Connect to the internet ( Router or Switch) via a net cable (Skip this step if local access)
Connect to the DC 48V-52V adapter and turn on the power.
1-2. Connection the Cameras.
First, determine the installation location of the camera, and connect the PoE camera to the NVR through the network cable.
Note: The single-channel PoE power supply supports up to 12V2.5A, which is 30W

1-3. Install HDD for NVR
1-3-1. Install HDD
Install the hard disk with Phillips screwdrivers.
It is recommended to use a hard disk with a capacity of 2TB-4TB for the 8-channel camera. The recording time is about 1-2 months. If you have not purchased a hard disk, please skip this step.

Loosening the srews on the panel’s rear and side.
Remove the cover from the NVR.
If there is an insulating sheet on the battery, please remove the insulating sheet first
Connect the data cable and power cable to HDD. Note: After the hard disk is connected, place it as shown in the figure, with the interface facing right, and facing left will block the AI ultra-long distance mode switch.
Fasten the screws on the bottom to fix the HDD.
Re-install the cover of the NVR and fasten the screws.

AI ultra-long-range mode switch introduction

When this switch is on ON Two green lights are on, and it is in ultra-long distance mode at this time, and it can operate with a PoE camera at a distance of about 250 meters (note: among the connected cameras, if any camera is more than 100 meters away, you need to turn on this model)
When this switch is on OFF A green light is on, and it is in short-range mode at this time, which can be used for PoE cameras with a distance of fewer than 100 meters.
Tips: To avoid repeated disassembly of the NVR, you can first estimate the distance between the farthest camera and the NVR to determine whether you need to turn on the ultra-long distance mode.

2. NVR Login
Follow the NVR startup wizard to complete the login settings. (NVR default password: 888888) 3. Network Setting
When the network shows an abnormal state! :
3-1. Check if your network cable is properly connected.
3-2. Double-click to open the network settings-select DHCP enable-OK.
3-3. If the DHCP function of the router is disabled, please enter the correct IP address manually.
3-4. If you still cannot access the Internet after changing the settings, try rebooting the VCR.

4. Add the Camera

Right-Click the Screen-Camera–Search — Add — OK
After finishing adding, if it prompts that the password is wrong, please click Edit in the added device, enter the camera password, our camera password is 888888

5. SriHome APP Setup
Step 1. crime App Installation Method

Scan the QR code to download the “SriHome” App. Method
Search”SriHome” on Google Play or iOS App Store.

|
---|---
https://play.google.com/store/apps/details?id=com.x.srihome| https://itunes.apple.com/us/app/srihome/id1327653710

Step 2. Register & Login on SriHome App
Step 3. Add the Device to App

Note: A. The ID of the device is stuck on the label of the video recorder shell B. Enter Desktop /Main Menu–My Device–Version- Serial NO.

Reset
Enter Desktop>Control Panel>Restore>Please select setting entries that you want to default.

How to share more users to watch in APP
To protect the user’s privacy, the first user is an administrator by default. Other users accessing the camera need administrator permission, or they cannot login even with ID and password. The way to get permission is as follows:
Access the “SriHome” App, tap Settings - > Visitor Management -> Add.
There are 2 types of permissions:
Operator: Live video view, set time, alarm, record, and network.
Visitor: Viewing video only in real-time
Note: You can find the user’s App ID in App Settings