Shenzhen Elenose Technology BH830 Air Conduction Wireless Headphone Instruction Manual
- June 8, 2024
- Shenzhen Elenose Technology
Table of Contents
Shenzhen Elenose Technology BH830 Air Conduction Wireless Headphone
Summary of button functions
- Power On/ Power Off/Volume up/Next song
- Volume down/Previous song
- Magnetic charging port
- LED indicator
- Microphone Call
- Call Noise Cancelling Microphone
Controls
On: When the headphone is in power-off state, press and hold power button
for 3 seconds with blue LED flickering, reminding tone: power on.
Off: When the headphone is in power-on state, press and hold power button
for 5 seconds with red LED flickering once, reminding tone: power off_ Connect
BT: When the headphone is in power-off state, press and hold it for 3 seconds
to enter a pairing state with red and blue LEDs flickering and reminding tone:
pairing.
After the device (smart phone, tablet computer, etc.) discovers BH830, press
it to connect.
Connected successfully: When the headphone is successfully linked to the
device, blue LED will flicker every 5 seconds with reminding tone: Connected
Pause/play: In the BT connection music playback state, Double-click the
boot button to pause, and double-click externally to play.
Answer/hang up: In the incoming call state: click the
Power on key to answer, long press the Power on key for 2 seconds to reject
the call. In the call state, click the Power on key to hang up
Vol+ : Press the Vol+ once to turn up the volume.
Vol-: Press the Vol- once to turn down the volume.
The next song: Long press “V+” for 2 seconds when music is playing
In a song: Long press RV-” for 2 seconds when music is playing
Voice assistant: Keep BT link, Three click the boot button to enter the
voice assistant, and then three times the boot button to exit the voice
assistant.
Reset: After plugging the charging line, the headphone will be reset and
powered off for charging.
Clear pairing Information: Press the power button and the volume off
button for 5 seconds to clear the pairing information in shutdown mode, Red
and Blue light blinks 1 second spontaneously
Charging : In case of using charging line for charging, connect the headphone with the USB power. During the charging, LED turns red. After charging, the LED turns blue.
How to wear
Hang the headphone behind your neck with both speakers clinging to your cheekbones. After that, adjust it until you feel comfortable.
Specifications
Music play time——————-7 hours(80% volume)
Standby time——20 days
Charging time———————1.5 hours
BT version————————–5.3
Speaker impedance————–16O±15%
Microphone sensitivity———–42±3db
Product weight——18g±2g
Connection distance————–15 meters
Charging voltage/current———5V/0.5A
Attentions
- Please wear the bone-conduction speakers of the headphone at your cheekbones before your ears and do not put them in your ears.
- Listening to music for an excessive long time maitake you feel uncomfortable, please try to use a medium volume instead of a big one.
- No matter how the volume is, please do not make it prevent you from hearing the surrounding sounds. Please take care when using the headphone.
- Do not throw, press the headphone or put it in the water.
- The headphone should keep away from fire, water and high voltage devices.
- It is not for children’s use as it contains small parts.
- Please do not treat it as domestic waste. Instead, send it to your electrical and electronic recycling station.
If there is any injury or property loss due to violation of the above contents, we will not bear any responsibility.
FCC Caution：
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>