HYPERICE 6474522 Hypervolt 2 Pro Premium Percussion Massage Device Instruction Manual
- June 6, 2024
- Hyperice
Table of Contents
HYPERICE 6474522 Hypervolt 2 Pro Premium Percussion Massage Device
IMPORTANT SAFETY INSTRUCTIONS – ORIGINAL INSTRUCTIONS
Read all instructions before using the Hypervolt 2 Pro.
DANGER
To reduce the risk of electric shock:
- Always unplug this device from the electrical outlet immediately after using and before cleaning.
- Do not reach for a device that has fallen into water. Unplug immediately.
- Do not use while bathing or in a shower.
- Do not place or store device where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.
WARNING
To reduce the risk of burns, fire, electric shock, or injury to persons:
- A device should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or taking off parts.
- Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.
- This device can be used by children aged from 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
- Use this device only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
- Never operate this device if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or if it has gotten wet. Return the device to a service center for examination and repair.
- Do not carry this device by supply cord or use cord as a handle.
- Keep the cord away from heated surfaces.
- Never operate the device with the air openings blocked. Keep the air openings free of lint, hair, or any substance which may impair the flow of air.
- Never drop or insert any object into any opening
- Do not use outdoors.
- Do not operate where aerosol (spray) devices are being used or where oxygen is being administered.
- Never operate on a soft surface such as a bed or couch where the air openings may be blocked.
- Do not use device in close proximity to loose clothing or jewelry.
- Keep long hair away from device while in use.
- Cleaning and user maintenance shall not be done by children without supervision.
- Do not remove screws or attempt to disassemble.
- Do not operate continuously for more than one hour. After one hour use, allow device to rest for 30 minutes before re-using.
- Unplug the device after charging and prior to use.
- Use device only according to Operating Instructions.
When using the Hypervolt 2 Pro use only on dry, clean surfaces of the body by lightly pressing and moving across the body for approximately sixty(60) seconds per region. The Hypervolt 2 Pro should only be used on soft tissue areas of the body and should not be used on any hard or bony areas of the body, including the head. Please immediately stop use of the Hypervolt 2 Pro upon experiencing any pain or discomfort, apart from light muscle soreness. Bruising can occur from use of the Hypervolt 2 Pro, regardless of the pressure setting, and if bruising does occur you should not use the Hypervolt 2 Pro on the bruised area until the bruise is fully healed. Use of the Hypervolt 2 Pro should also be avoided on all bruises, contusions, rashes or irritated or injured areas of the skin until they are fully healed. When using the Hypervolt 2 Pro be sure to keep fingers, toes, hair, and other body parts away from the back of the attachment head to avoid pinching or hair entanglement. The Hypervolt 2 Pro should only be charged with the double insulated, 18VDC Hyperice charger (model number MX24Z2-1801000) that was supplied with the device. Do not charge the Hypervolt 2 Pro overnight or leave the Hypervolt 2 Pro unattended when charging or in use. Please do not use the Hypervolt 2 Pro, or any percussion device without first obtaining approval from your physician if any of the following apply:
Pregnancy, diabetes with complications such as neuropathy or retinal damage, wear of pacemakers, recent surgery or injury, epilepsy or migraines, herniated disks, spondylolisthesis, spondylolysis, or spondylosis, recent joint replacements or IUD, metal pins or plates or any concerns about your physical health. Frail individuals and children should be accompanied by an adult when using any percussion or vibration device. These contraindications do not mean that you are not able to use a percussion or vibration device but we advise that before doing so you consult your physician. Ongoing research is being done on the effects of percussion massage for specific medical disorders that may result in the shortening of the list of contraindications as shown above. The Hypervolt 2 Pro contains a battery which must be complied with safely at an appropriate e-waste disposal or recycling facility.
CAUTION
The battery used in this device may present a risk of fire or chemical burn if
mistreated. Do not disassemble, heat above 100º C or incinerate. Dispose of
used battery promptly. Keep away from children.
SAVE THESE INSTRUCTIONS
The Hypervolt 2 Pro is a handheld percussion massage device that delivers targeted pulses of pressure to care for muscles, relieve tension, provide a relaxing massage, accelerate warmup and recovery, and help maintain flexibility and range of motion.
OPERATING
Switch your Hypervolt 2 Pro to the ON position at the base of the handle. The
LED band on the handle will illuminate indicating the battery level. Turn the
digital speed dial clockwise to the desired speed setting indicated by the LED
lights illuminating on the face of the control panel. Your Hypervolt 2 Pro is
now ready for use. The lowest speed is at the nine o’clock position and the
highest speed is at the twelve o’clock position. Turning the dial clockwise
will increase the speed. To turn off the percussion, rotate the digital
control dial counter clockwise until all five of the LEDs are turned off.
CHANGING HEAD ATTACHMENTS
Only change attachments after speed setting is turned to off and head
attachment stopped moving. To change head attachments, pull the existing head
attachment straight out to remove and insert the desired head directly into
the opening while pushing firmly. For the Forkhead attachment align the tab on
the fork with the groove on the opening and push firmly.
CHARGING
Fully charge battery for up to four hours before first use with the battery
either attached or detached from the device. To charge, connect the DC end of
the supplied 18V charger to the charging port on the bottom of the
battery/handle and plug the charger into a wall outlet. The LED light band
colors correspond to the charge level ranging from red (low) to green (fully
charged). Full charge is indicated when the LED band remains green and fully
illuminated. Battery may be recharged at any time and at any battery level. It
is not recommended to fully deplete the battery to the red LED level. The
average runtime is 2+ hours depending on speed level and pressure applied
during use. It is recommended to toggle the power switch to OFF while the
device is not in use and during storage and travel.
CLEANING AND STORAGE
Make sure the power is OFF and the battery charger is not attached. Use a
damp, clean cloth and gently wipe your Hypervolt 2 Pro. Store in a clean,
cool, dry place, not in direct sunlight, when not in use.
CONNECTING TO THE HYPERICE APP
To connect your device to the Hyperice App via Bluetooth® make sure that your
device is turned on, Bluetooth® is turned on in your phone, and your device is
within close proximity. Select a routine within the Hyperice App and if
prompted tap “Scan for Devices.” Select your device when it pops up on the
screen. HyperSmart™ will automatically start your device and adjust the speed
and intensity as you follow along with the routine.
-
AC-DC Charger: 100-240V – 50/60Hz 0.7A – 18.0V1.0A 18.0 W
Rechargeable lithium-ion battery 4100mAh -
Frequency: Level 1 – 1700/28 Hz, Level 2 – 1900/32 Hz, Level 3 – 2100/35 Hz,
Level 4 – 2400/40 Hz, Level 5 – 2700/45 Hz -
Weight: 2.6 lbs/1.18 kg
Designed in the USA. Assembled in China.
WARRANTY
If within one year from the date of purchase, this device fails due to a
defect in material or workmanship, Hyperice, Inc. will repair or replace the
device, or necessary components, free of charge.
This warranty excludes:
- damage caused by accident, abuse, mishandling, or transport;
- devices subjected to unauthorized repair;
- devices not used in accordance with Hyperice care instructions;
- damage exceeding the cost of the device;
- deterioration of the delivered device resulting from abnormal storage and/or safeguarding conditions on the client’s premises, and
- failure to provide the dated proof of purchase.
Some states and countries do not allow a limitation of damages, so the foregoing limitation may not apply to you. This warranty guarantees specific legal rights, and but other rights may vary from country to country and from state to state. This warranty service is available through the operating policies and procedures of Hyperice, Inc., and all Hyperice international distributors. If you are a client, please contact the appropriate Hyperice business entity, dealer, or retailer, from whom you directly purchased the device for warranty and return authorization procedures. This warranty is initiated and executed by Hyperice, Inc.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>