PENTAIR 79011359 Dorado Automatic Pool Cleaner User Guide
- June 5, 2024
- Pentair
Table of Contents
DORADO™
AUTOMATIC POOL CLEANER
INSTALLATION AND USER’S GUIDE
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
IMPORTANT WARNING AND SAFETY INSTRUCTIONS
Important Notice:
Attention Installer: This guide contains important information about the installation, operation, and safe use of this product. This information should be given to the owner and/or operator of this equipment after the installation of the pool cleaner.
Attention User: This manual contains important information that will help you in operating and maintaining this pool cleaner. Please retain it for future reference. Consult Pentair with any questions regarding this equipment.
WARNING: Before installing this product, read and follow all warning notices and instructions which are included. Failure to follow safety warnings and instructions can result in severe injury, death, or property damage. Call 800-831-7133 for additional free copies of these instructions.
Consumer Information and Safety
This pool cleaner is designed and manufactured to provide many years of safe
and reliable service when installed, operated, and maintained according to the
information in this manual. Throughout the manual, safety warnings and
cautions are identified by the “ **** ” symbol. Be sure to read and comply
with all of the warnings and cautions.
WARNING: HAZARDOUS SUCTION.
Do not play with cleaner or hose or apply to body. Can trap and tear hair
or body parts. The hose can trip or entangle swimmers which could result in
drowning.
WARNING:
SUCTION ENTRAPMENT, INJURY, AND DROWNING HAZARD. If your pool has a dedicated suction port (“vac port”) for vacuuming or for an automatic pool cleaner, it must be covered when not in use. A spring-loaded safety cover (a “vac port fitting”) is included with your cleaner. Install it on the suction port to prevent entrapment and injury. If the cover provided does not fit, purchase one that does from your local pool store and install it instead. The cover should conform to IAPMO SPS4-99A.
WARNING: Stop pump before attempting to clean unit. Do not allow swimmers
in the pool while the pool cleaner is operating.
WARNING: To reduce the risk of injury, do not let children use or play
with the pool cleaner.
WARNING: Do not allow swimmers in the pool while the pool cleaner is
operating. The hose can trip or entangle swimmers which could result in
drowning.
CAUTION: Moving parts may injure hands or fingers. Stop pump before
attempting to clean out pool cleaner head.
General Installation Information
Pre-Installation Check List
Before installing your cleaner, review and understand all warnings and safety
information in this guide. Failure to follow these instructions or improper
installation of the cleaner can result in damage to the pool finish or the
vinyl liner, Most cleaners are not designed to traverse from floor to wall
when the pool cove is 90%. There may be other structures installed in the pool
that the cleaner cannot navigate, BE AWARE and supervise the cleaner during
unique conditions. Pentair Water Pool and Spa, Inc. disclaim any liability for
repairs or replacement to any of these structures or components of the
customer’s pool.
Before installing the cleaner in a vinyl liner pool:
Check the liner closely for signs of deterioration or damage from age,
chemicals, pool wall damage, etc. If any damage is found, have a qualified
pool professional make all the necessary repairs. Also, if there are stones,
roots, etc., under the liner, remove them before installing the cleaner.
Before installing the cleaner in a gunite pool or a pool that is partially
or completely tiled:
Make sure the pool finish is in proper condition as staining, etching,
cracking or delaminating may worsen.
Repair loose tiles and tighten any loose light rings.
Before installing the cleaner, clean your filter system:
Make sure you have cleaned the filter, including backwashing, rinsing, and
emptying all baskets. A clean system is necessary for proper cleaner operation
and coverage.
Before installing the cleaner, understand cleaner coverage:
The cleaner is designed to rid your pool of debris in approximately 4-6 hours.
Less time could be needed, depending on the pool size. The cleaner was not
designed to automatically clean steps or swim outs or to work under a solar
cover. The cleaner may get stuck in these areas which can result in damage to
the pool finish or vinyl liner. Pentair Water Pool and Spa, Inc. disclaim any
liability for repairs or replacement to any of these structures or components
of the consumer’s pool. It was also not designed to do the initial cleanup for
a new pool or when opening your pool for the season.
AFTER installing the cleaner, make sure the cleaner is operating
correctly:
The cleaner may need some minor adjustments to make sure it is operating
properly so there is no damage to the pool finish. Certain vinyl liner
patterns are particularly susceptible to surface wear, pattern removal, ink
rubbing off, or serious scratches to the pattern caused by objects coming into
contact with the vinyl surface, including automatic pool cleaners. Pentair
Water Pool and Spa, Inc. is not responsible for any pattern removal,
abrasions, or markings on vinyl liners. Periodically inspect the cleaner
components and the cleaner performance to ensure it is operating as designed.
Replace and/or repair any worn or damaged components. Failure to follow
instructions or improper installation of the cleaner may result in damage to
the cleaner, pool finish, or vinyl liner.
Warnings and safety instructions for Pentair Water Pool and Spa Pumps and
other related products are available at: http://www.pentairpool.com/pool-
owner/safety-warnings/ or call
800-831-7133 for additional free copies
of these instructions.
Please refer to http://www.pentairpool.com/pool-owner/safetywarnings/ for
warning and safety instructions related to this product.
Disclaimer of Liability About your Pool and Cleaner
There is a multitude of factors that contribute to the life of your pool. The
pool cleaner is a very passive product that will have no impact on pool life.
Please be aware that over time, deterioration, discoloration, and brittleness
of any pool finish can be caused separately by, or in combination with, age,
an imbalance in pool water chemistry, improper installation, and other
factors. Pressure side pool cleaners will not remove or cause wear on “good”
pool plaster. In fact, the opposite is true–pool plaster will eventually cause
wear on the cleaner.
The same situation holds true for vinyl-lined in-ground swimming pools because vinyl liners are also affected by the environment and factors such as pool water chemistry, sunlight, and the pool’s surroundings. Therefore over time, vinyl can become brittle and weak. In addition, vinyl-lined pools are affected by the workmanship, composition, and installation of the liner and the workmanship and quality of construction of the supporting walls and pool base. These are all factors that can contribute to liver failure. The existence of any of these types of conditions in your pool is not caused by the use or operation of the pool cleaner. The manufacturer disclaims any liability for repairs or replacement to any of these structures or components of the customer’s pool.
The pool owner must assume all responsibility for the condition and maintenance of the pool’s surface, water, and deck.
Before the cleaner is installed, please take a moment to record the serial
number. This number is located on your warranty card and on the back of the
cleaner near the rear jets. You will be asked for this number when you contact
our Technical Support Department.
SERIAL #__
SAVE THESE INSTRUCTIONS
POOL PREPARATION
Congratulations on your purchase of the Dorado™ Automatic Pool Cleaner!
Nothing quite compares to the Dorado’s ability to make dirt disappear. With
its 15” cleaning path and unique bristle drive, your Dorado automatic pool
cleaner will deliver fast, complete coverage of your pool. First, however,
you’ll have to install the cleaner and perhaps make some minor adjustments.
This manual covers the steps needed to install, adjust and maintain your new
cleaner.
Preparing Your Pool
Before you assemble and install your cleaner, you should make sure that your
pool is clean and free of algae. If necessary, make the following preparations
before proceeding.
- Chemically balance the pool water
- Brush the pool and let the debris settle
- Hand vacuum the pool thoroughly
- Clean the filter and pump strainer basket (Figure 1)
Cleaner Components
Remove the cleaner and all of its parts from the box and check to make sure
that all components were included (Figure 2).
- Cleaner
- Swivel Assembly
- Handle Adapter
- Reducer Cone
- Leader Hose: One 40” (1.02 m) length
- Hose: Eleven 40” (1.02 m) lengths
- Vacuum Regulator
- Regulator Cap
- Vacuum Port Fitting
- Flow Gauge
ASSEMBLING THE CLEANER
Attaching Swivel Assembly to Cleaner Head
Installing the swivel assembly is a snap. Just insert it into the Dorado™
Automatic
Pool Cleaner body and give it a quarter-turn (Figure 3).
If you attach an unadapted handle to the swivel for manual vacuuming, be sure
it is the special, floating unadapted handle provided with the cleaner
(Replacement Part No. GW9019). The use of a different unadapted handle will
hinder the cleaner’s performance.
Assembling the Hose
The cleaner includes twelve sections of hose, each 40 in. (1.02 m) in length
(Figure 4). Do not cut the hose lengths. You will need to connect these
40” sections of hose to create a combined hose length that is at least 4 ft.
(1.22 m) longer than the distance from your suction source (whether skimmer or
dedicated suction line) to the farthest point in the pool (Figure 5).
Connect the hoses by twisting and pushing the female ends onto the male ends
after wetting the ends in the pool (Figure 6).
A special “leader” hose section is designed to connect to the cleaner’s swivel assembly and therefore has a larger hose cuff than the other hose lengths (Figures 7 and 8). Failure to use this leader hose section to attach the hose to the cleaner’s swivel assembly will hinder your cleaner’s performance. If the additional hose is needed, use only hoses from your Pentair Water Pool and Spa dealer (order replacement part No. 41200-0131). The use of another manufacturer’s hose will hinder cleaner coverage.
INSTALLATION
This section describes how to install the Dorado™ Automatic Pool Cleaner. The cleaner is designed to work in a wide variety of swimming pools. Both the standard in-skimmer installation and optional vac port installation are covered below. If your pool configuration is unlike any of the examples, contact your Pentair Water Pool and Spa dealer for assistance, or call Pentair at 1-800-831-7133.
Standard Installation
For pools with one skimmer, using the vacuum regulator
The manufacturer recommends the Standard Installation through the pool’s skimmer (Figure 8). The advantage of this installation is its use of the vacuum regulator to balance the water flow between the skimmer and the pool cleaner. The vacuum regulator can be adjusted to changes in the amount of water flow to provide the cleaner with the power necessary to ensure proper cleaning performance, and the manufacturer strongly recommends its use for maximum safety and performance.
-
Turn the pool pump off
-
Adjust valves for vacuuming
Adjust the pump valves (if your system has valves) to direct all suction to the skimmer. Close the main drain and all suction lines, except the line from the skimmer to which the cleaner will be connected. -
Remove the skimmer basket from the skimmer
-
Install vacuum regulator
WARNING: Hazardous suction. Can cause entrapment with severe personal injury or drowning.****
Use the vacuum regulator in conjunction with your pool cleaner system at all times. The vacuum regulator has an adjustment knob If suction is too high, the knob is turned counterclockwise to decrease the suction. If the suction is too low, the knob is turned clockwise to increase the suction.
The vacuum regulator must be installed in conjunction with the reducer cone (Figure 9). The reducer cone is required to make most skimmer connections. It will keep the hose and vacuum regulator in place once the filter system is stopped.
To install the vacuum regulator, insert the vacuum regulator and reducer cone
in the skimmer. Attach the end of the hose to the regulator (Figure 10).
Make sure the vacuum regulator is submerged at all times. If not, the pump
will suck air through the vacuum regulator and lose its prime. This could
damage the pump.
-
Check Flow
With the main drain closed, and one end of the hose attached to the regulator installed in the skimmer, insert the flow gauge into the other end of the hose. Keep the hose and flow gauge underwater. Turn on the pump. With the pump running, adjust the vacuum regulator (in your skimmer) until the indicator on the flow gauge is between the minimum and maximum flow (Figure 11). Remove the flow gauge and proceed to step 6. -
Connect Hose to the Cleaner’s Swivel Assembly
Connect the large hose cuff (Figure 12) of the leader hose to the swivel assembly on the Dorado™ Automatic Pool Cleaner head (Figure 12). Push the cleaner into the pool and let it sink to the bottom (Figure 13).
-
Turn the pool pump on
After completing the installation, turn the pool pump on and allow it to run for a couple of minutes to ensure that all air cycles out of the system.
Optional Installation
Vac Port Installation with Vacuum Regulator in Skimmer
If your pool has a vac port (Figure 14), you can install Dorado™ Automatic Pool Cleaner using the Optional Installation.
-
Turn the pool pump off
-
Adjust valves for vacuuming
Adjust the pump valves (if your system has valves) to direct all suction to the dedicated vacuum line and the skimmer. Close the main drain and all suction lines, except the line from the dedicated vacuum line to which the cleaner will be connected, and the skimmer where the vacuum regulator will be installed. -
Install vac port door fitting.
WARNING: Suction entrapment, injury, and drowning hazard. If your pool has a dedicated suction port (“vac port”) for vacuuming or for an automatic pool cleaner, it must be covered when not in use.
A spring-loaded safety cover (the “vac port fitting”) is included with this pool cleaner (Figure 15). Install it on the dedicated vacuum line to prevent entrapment and injury. For details please refer to the Vac Port Instruction sheet included with your vac port fitting. To install the included vac port fitting:
1. Screw the vac port fitting into the dedicated vacuum line opening.
2. Orient the vac port fitting so the arrow on the door points up.
3. Secure the cover by tightening the Allen screw below the door, into the dedicated vacuum line fitting. -
Remove the skimmer basket from the skimmer
-
Install vacuum regulator.
WARNING: Hazardous suction. Can cause entrapment with severe personal injury or drowning.
To install the vacuum regulator, insert the vacuum regulator and reducer cone in the skimmer (Figure 16).
To prevent water from flowing through the top of the vacuum regulator, attach the regulator cap to the vacuum regulator ( Figure 17 ). Attach the end of the hose to the vac port fitting installed in the dedicated vacuum line ( Figure 16 ). -
Check Flow
With the main drain closed, and one end of the hose attached to the vac port fitting installed in the dedicated vacuum line, insert the flow gauge into the other end of the hose. Keep the hose and flow gauge underwater. Turn on the pump. With the pump running, adjust the vacuum regulator (in your skimmer) until the indicator on the flow gauge is between the minimum and maximum flow (Figure 18). Remove the flow gauge and proceed to step 7. -
Connect Hose to the Cleaner’s Swivel Assembly
Connect the large hose cuff (Figure 19) of the leader hose to the swivel assembly on the Dorado™ Automatic Pool Cleaner head. Push the cleaner into the pool and let it sink to the bottom (Figure 20). -
Turn the pool pump on
After completing the installation, turn the pool pump on and allow it to run for a couple of minutes to ensure that all air cycles out of the system.
OPERATION
This section contains information describing the movement and operation of your Dorado™ Automatic Pool Cleaner, as well as tips for “fine-tuning” your pool’s valves and connections to optimize the cleaner’s cleaning ability.
Cleaner Operation and Movement
Clicking sound
This is the sound of the oscillator moving back and forth in the oscillator
chamber. The best speed for it is about 500 oscillations per minute. The
vibration created by the oscillator moves the bristles and the cleaner. If the
oscillator is running too fast, the cleaner will have a tendency to climb up
the pool wall past the waterline, or “walk out of the pool” and suck air.
Reduce the speed by adjusting the vacuum regulator in the skimmer.
Movement around the pool
Random motion – The cleaner will visit most spots in the pool within a
six (6) hour period. It is not specifically programmed, and cannot see the
dirt you are seeing. It is a random motion pattern.
The cleaner was designed to spend most of its time in the deep end, where most
of the floor and wall area exists. During a six (6) hour period, the cleaner
will visit the shallow end a few times.
Rotating motion – The cleaner will rise up on one side and pivot a few times per minute. This is normal and provides the following:
- Allows leaves that are being pushed or dragged along to be sucked up into the vacuum chamber.
- Allows the cleaner to:
Change direction
Get out of corners
Get away from ladders
Submerge below pool water level
Get off of domed main drain covers
Picks up “big stuff”
The cleaner will pick up some debris so large that it may jam. Simply stop the
pump and remove the debris from the oscillator, or the swivel assembly.
Fine-tuning Valves and Connections
WARNING: Pool pump suction is hazardous and can cause entrapment with severe personal injury or drowning. Use a vacuum regulator (see instructions below) in the pool cleaner system at all times.
NOTICE: Each pool’s hydraulic system and vacuum connections are different. Be sure you have installed the vacuum regulator before you “fine- tune” the system. This not only regulates vacuum but also acts as a safety device.
WARNING: Suction entrapment, injury, and drowning hazard. If your pool has a dedicated suction port (“vac port”) for vacuuming or for an automatic pool cleaner, it must be covered when not in use. A spring-loaded safety cover (the “Vac Port Fitting”) is included with this pool cleaner. Install it on the vac port to prevent entrapment and injury. For details please refer to the Vac Port Fitting instruction sheet included with your cleaner.
For the novice pool owner for whom pool vacuuming is a new experience, please read all of the following points, installation instructions, and troubleshooting guide carefully.
Please note the following:
- “Vacuum” and “suction” are two words meaning the same thing.
- “Dedicated suction line”, “vac port”, and “vac fitting” are different terms for a hole in the sidewall of a pool; this hole is connected to the pump suction and is dedicated to vacuuming.
- Some pools do not have a vac port. If your pool does have one, please read the “Suction Entrapment” warning above.
For the seasoned pool owner: The Dorado™ Automatic Pool Cleaner connection and vacuum adjustments can be similar to using your manual pool vacuum. Please read on.
Valves (Pump, Skimmer, and Main Drain) and Vacuum Adjustments
You may need to spend some time adjusting the skimmer and main drain valves in
order to obtain the best vacuum setting for good cleaner operation. Once you
have found the correct valve settings for the best operation, we suggest you
mark the valves to ensure repeated success.
At first, set valves to give maximum vacuum to the skimmer or vac fitting you
have elected to use.
Too Much Vacuum?
You have too much vacuum if the cleaner climbs up the pool wall past the water
line to the point that the cleaner sucks air and the pump loses prime.
Frequent loss of prime will damage the pump. To correct this, adjust the
regulator by turning the adjustment knob counterclockwise. This will decrease
the suction. If the cleaner still climbs out and sucks
air, open the main drain valve slightly.
Not Enough Vacuum?
You don’t have enough vacuum if the cleaner moves sluggishly or not at all. Be
sure the filter system is clean and the regulator and all valves are adjusted
to give you maximum vacuum. If the cleaner is still not moving, your pump may
not be strong enough to operate the cleaner. Please refer to “Troubleshooting”
on Page 17.
In-Line Leaf Canisters
If your pool is exposed to large quantities of leaves, we suggest purchasing
and installing an in-line leaf canister (part no. R211084K). A leaf canister
will provide more debris-loading capacity and also provides a water by-pass
when the canister is full. It is very important that the pump not starve for
water!
Skimmer Connection
For pools that have large quantities of “big stuff” to pick up, we suggest
using the bottom of the skimmer connection in conjunction with an in-line leaf
canister (part no. R211084K). A leaf canister will provide more debris-loading
capacity and also provides a water by-pass when the canister is full. It is
very important that the pump not starve for water!
Skimmer Vac Plates
Some pool owners connect the hose to a skimmer vac plate, which allows the
skimmer basket to remain in the skimmer. If this method is used, empty the
basket frequently. Also, make sure that the vacuum regulator provided is
completely submerged so that it will not suck air and damage the pump.
Skimmer Vac Plate Vacuum Control Adjusters
Some pool owners use one of a variety of manufacturers’ skimmer vac plates.
Some have a vacuum control adjuster, and some do not. The adjuster could be a
screw-type, a spring-loaded apparatus, or a dial design. For those vac plates
with adjusters, it is important to adjust them when fine-tuning the vacuum for
the Dorado™ Automatic Pool
Cleaner.
MAINTENANCE
This section describes the service and maintenance of the Dorado™ Automatic Pool Cleaner.
WARNING: Hazardous suction. Stop pump before attempting to clean pool cleaner.
- Keep the skimmer basket and pump strainer basket clean and free of debris.
- If cleaner jams with large debris (leaves, sticks, etc.), try cleaning debris first from the bottom of the unit. If this doesn’t clear the unit, remove the top swivel assembly (turn 1/4 turn) and clear the debris from the top.
- Remove the pool cleaner from the pool before super chlorinating (shocking) or chemical balancing. Wait at least four hours after the chemical procedure before reinstalling the cleaner.
- Make sure that the cleaner’s brush bristles don’t become deformed during storage. Store the unit so that it doesn’t sit on the bristles and so that nothing compresses them.
- Do not coil the hose. Remove the hose from the cleaner when removing the cleaner from the pool. Store the hose flat and straight.
- Periodically examine bristles and vacuum skirts for wear or distortion. Replace if necessary. See “Reassembly”, Page 17.
- Don’t store the cleaner with the hose connected to the cleaner body or with the hose coiled. To do so will cause the hose to take a set or kink over a period of time. When reinstalled in the pool, the hose will tend to stay coiled and will cause the cleaner to malfunction.
- If the hose has taken a set, uncoil it as far as possible without damaging it and lay it out in the sun for several hours to straighten itself. Once it has relaxed and straightened out, store it laid out flat and straight (no coiling).
- Make sure the lift brush is retracted during storage. If the lift brush is down during storage and the cleaner rests on it, the brush bristles will collapse over time and the cleaner will no longer turn during operation as it was designed to do.
Hose Storage
Disassembly
-
Remove swivel assembly (Figure 22) from the top of the Dorado™ Automatic Pool Cleaner by turning it 1/4-turn counterclockwise and pulling it straight up on it.
-
Turn the cleaner upside down. Remove 6 screws and remove the lower body assembly from the shroud.
-
Turn lower body assembly right side up. Unsnap the 2 clips on the oscillator chamber cap (Figure 23a); lift it off.
-
Pull the long gear shaft straight up (Figure 23a) by the blocks on the ends of the shaft. Hold the seals in the oscillator and the blocks on the shaft. The cam may interfere with the shaft mounting post; if so, turn it slightly on the shaft until it clears the post. The shaft assembly can now be disassembled (Figure 23b).
-
Slide the long gear shaft out of the oscillator (with gears, complete); make sure that you don’t lose the seals out of the oscillator which may fall out at this point (Figure 23b).
5A. Oscillator seals are replaceable.
5B. Ratchet gear set and long shaft are replaceable as a unit. -
Remove the set screw, short gear shaft, and gears (Figure 24); be sure to keep the gears on.
-
With a small screwdriver (such as a jeweler’s screwdriver), a pencil, or a pen point, depress and remove the coil spring from the lift brush mounting post (Figure 25). Replace the brush and the spring if necessary.
-
The metal ratchet tab slides out of its slot sideways; replace it by removing the center brushes and sliding in a new ratchet tab until it is flush with the edge of the plastic holder (Figures 26 and 27). Replace the center brushes.
-
The brush ring pops out of the cleaner body for easy replacement.
-
If you need to replace the bumper, turn the shroud and bumper assembly upside down and remove the two screws holding the bumper to the shroud.
Reassembly
- Put both white seals in the oscillator; hold them in place.
- Install the oscillator on the long gear shaft. Install the ratchet gear on the shaft so that the teeth engage the ratchet on the oscillator. Install the spring, ratchet drum, pinion gear (large gear first), and cam (gear end first) on the shaft (see Figure 28). Hold the gears on the shaft while installing them, and compress the clutch spring to allow the assembly to slip into place between the posts (see Figure 28).
- Install the long gear shaft and end blocks in the cleaning head with the large arm of the cam down (see Figure 29).
- Reinstall the short gear shaft, set screw, and two gears (see Figure 30); the small pinion gears and the shaft set screw go on the side toward the end of the cleaner – away from the oscillator box. Make sure that the gears engage the gears on the long gear shaft.
- Install the oscillator chamber cap and clip it in place.
- Install the rubber vacuum skirt on the cleaner with the word ‘OUTSIDE’ showing. Start at the large pin on the back of the cleaner head (see Figure 31) and work around the cleaner. Make sure the skirt is flush against the stop strips on the cleaner head (see Figure 32).
- Turn the cleaner over. If you removed the bumper and brush ring, replace them now.
- Install the lower body assembly in the shroud. Fasten the cleaning head in place with 6 screws (2 long, 2 short – see Figure 33).
NOTE: Make sure that you do not dislodge the rubber vac skirt while inserting the lower body assembly past the brush ring.
Illustrated Parts List
Item No.| Description|
Part No.
---|---|---
1| Swivel Assembly| GW9012
2| Bumper| 360152
2A| Bumper Insert Kit (Incl. 2 Bumper Inserts and 4 Bumper Insert Screws)|
360154
3| Screw Kit (6 short, 2 long)| GW9504
4| Shroud| 360153
5| Brush Ring| GW9505
6| Oscillator Chamber Cap| GW9506
7| Cam Kit (2 & 3 Leg Cams)| GW9507
8| Idler Gear Kit (Incl. 3 Gears)| GW9509
9| Block Kit (Incl. 2 Blocks)| GW9512
10| Long Gear Shaft (Stainless Steel)| GW9513
11| Set Screw #4 Self Tapping##|
11A| Shaft Kit, Stainless Steel (Incl. Set Screw)| GW9536
12| Lower Body*| GW9535
13| Lift Brush| GW9517
14| Vacuum Skirt| GW9508
15| Lift Brush Spring| GW9522
16| Ratchet Tab (Stainless Steel)| GW9523
17| Oscillator Seal Kit (Incl. 2 Seals)| GW9004
18| Oscillator Assembly Kit (Incl. Key #17) (Ratchet Assembly not sold
separately)| GW9503
19| Center Brush Kit (Set of 2)| GW9013
•| Hose Kit, 12 sections, every 4 ft in length| 41200-0131
•| Vacuum Regulator| 41200-0200
•| Vacuum Regulator Cap| 41200-0211
•| Reducer Cone| GW9015
•| Unidad Handle| GW9019
•| Vac Port Fitting| GW9530
•| Flow gauge| 41200-0210
(•) – Note Shown
( *** ) – Includes Item Nos. 6, 11A, 13, 15, 16, two idler gears, and a
2-arm cam
(##)** – Not available separately
DORADO™ Automatic Pool Cleaner Installation and User’s Guide
TROUBLESHOOTING
SITUATION
|
SOLUTIONS:
---|---
The cleaner does not move Oscillator is very slow| 1. Backwash and/or
clean filter. Empty all baskets. This should help your cleaner attain the
desired oscillation. Correct oscillator speed can be determined by using the
flow gauge provided with the cleaner (see page 4).
2. Clear all debris from the oscillator chamber, hose, or vac plate by-pass
(if you have one).
3. Repair all sources of vacuum leaks (cracked vac plate, vac plate or
reducer cone not seated properly, cracked hose, vac regulator adjusted too
loosely).
4. Adjust valves to give maximum vacuum to the vacuum port or skimmer to
which you are attaching the cleaner hose. Reduce or shut off other skimmers
and the main (floor) drain. NOTE: Each pool’s hydraulic system is
different. It may require some adjustments to the skimmer and main valves
before you achieve the vacuum setting required for the best cleaner operation.
Once determined, mark the valves at that position to ensure repeated success.
5. Filtration system (pump) does not develop enough vacuum. Consult your pool
service professional.
6. In hot water, the hose may kink. The hose, when old, may have developed
leaks (cracks or holes) or may get brittle. Purchase a new hose.
NOTE: It must be a Dorado hose for proper operation.
Cleaner climbs past the waterline of the pool causing the pump to lose
prime (suck air)| 1. Oscillator is running too fast. Make sure the vacuum
regulator is installed and adjusted.
2. If step 1 does not solve the problem, slightly open the main drain valve
until the cleaner no longer climbs out of the pool.
Cleaner coverage not as expected| 1. A clean filter system will help
the cleaner to move much faster. Also, be sure to clean all baskets.
2. Vinyl liner pools with a deep end hopper will require 6-8 hours to clean.
During this time the cleaner should make at least 4 trips to the shallow end.
If not, call Customer Service at
1-800-831-7133.
3. Examine the lift brush mechanism as the cleaner is operating. To do this,
you will have to turn the cleaner over while it is running and submerged. If
the lift brush does not move to the “down” position within 2 minutes, call
Customer Service at 1-800-831-7133.
4. The cleaner was not designed to work under solar covers. If you have a
solar cover, only minimal coverage can be expected.
5. Any cleaner might miss a spot. Your cleaner has been designed to
accommodate the attachment of a vac-pole (telephone) by use of the handle in
the accessory bag. Attach pole for spot cleanups, steps, and swim outs.
Cleaner “stuck” in one spot (more than 15 mins)| 1. Examine the lift
brush mechanism as the cleaner is operating. To do this, you will have to turn
the cleaner over while it is running and submerged. If the lift brush does not
move to the “down” position within 2 minutes or less, call Customer Service at
1-800-831-7133.
Steps and “swim-outs” are not clean| 1. This cleaner was not designed
to clean these areas. Use the handy telephone attachment, connect the pole,
and clean missed areas.
The cleaner flips on its back when the pump stops| 1. This is normal
with some filter systems that develop a surge of back pressure when the system
shuts off. The cleaner will right itself when the system is restarted.
Hose comes loose when the pump stops| 1. Use the reducer cone when
connecting to the skimmer or vac port.
Cleaner hovers in one area with hose fully extended| 1. Hose might be
too short. The desired length can be measured from the point where the hose is
connected, to the furthest point of the pool, plus a minimum of an additional
4’. If needed, purchase an extension hose from your local dealer. Do not cut
the extension hose – use its full length even if it is a little long.
Hose keeps coiling up| 1. For best results, when the hose is not in
use, store it uncoiled, flat, and straight.
2. Lay the hose out flat and straight in the sunlight for a few hours prior
to use.
Cleaner avoids shallow end of the pool| 1. This could be caused by a
buoyancy issue. Add a hose weight (P/N 41201-0238; sold separately) to the
cleaner hose.
CUSTOMER SERVICE/TECHNICAL SUPPORT
If you have questions about ordering Pentair Aquatic Systems replacement parts, and pool products, please use the following contact information:
Customer Service (8 A.M. to 4:30 P.M. — Eastern and Pacific Times)
Phone: 800-831-7133
Fax: 800-284-4151
Web site
visit: www.pentairpool.com or
www.staritepool.com to find more information
about Pentair products.
Technical Support
Sanford, North Carolina (8 A.M. to 4:30 P.M. ET)
Phone: 919-566-8000
Fax: 919-566-8920
Moorpark, California (8 A.M. to 4:30 P.M. PT)
Phone: 805-553-5000 (Ext. 5591)
Fax: 805-553-5515
1620 HAWKINS AVE., SANFORD, NC 27330 •
919-566-8000
10951 WEST LOS ANGELES AVE., MOORPARK, CA 93021 •
805-553-5000
WWW.PENTAIRPOOL.COM
All Pentair trademarks and logos are owned by Pentair or one of its global
affiliates. Pentair Aquatic Systems and Dorado™ are trademarks and/or
registered trademarks of Pentair Water Pool and Spa, Inc. and/or its
affiliated companies in the United States and/ or other countries. Unless
expressly noted, names and brands of third parties that may be used in this
document are not used to indicate any affiliation or endorsement between the
owners of these names and brands and Pentair Water Pool and Spa, Inc. Those
names and brands may be the trademarks or registered trademarks of those third
parties. Because we are continuously improving our products and services,
Pentair reserves the right to change specifications without prior notice.
Pentair is an equal opportunity employer.
© 2016 Pentair Water Pool and Spa, Inc. All rights reserved. This document is
subject to change without notice.
P/N 371782 REV. A 4/15/16
Documents / Resources
|
PENTAIR 79011359 Dorado Automatic Pool
Cleaner
[pdf] User Guide
79011359, Dorado Automatic Pool Cleaner, 79011359 Dorado Automatic Pool
Cleaner
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>