eta 1180 Delizio Lever Coffee Maker User Manual

eta 1180 Delizio Lever Coffee Maker

INSTRUCTIONS FOR USE

Dear customer, thank you for purchasing our product. Keep these instructions including the warranty, the receipt, and, if possible, the box with the internal packing.

SAFETY WARNING

GENERAL PROVISIONS:

• Before the first use, read the instructions for use carefully, look at the picture and store the instructions for use for the future. Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.
• Check whether the data on the type label corresponds with the voltage in your socket. The power cord plug has to be connected to the properly connected and grounded socket according to the national standard
• This appliance may only be used by children aged 8 years or older, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Children younger than 8 years must be kept out of reach of the appliance and its power cord.
• Children must not play with the appliance.
• Before replacing accessories or accessible parts that are moving during operation, before assembly and disassembly, before you fill the water tank, before cleaning and maintenance, before the transfer, if the appliance is left unsupervised, or if you finish using it, make sure to switch OFF the appliance and unplug it from the mains by pulling the plug from the socket!
• Before you remove any accessible parts, before maintenance and handling, allow the appliance and any parts thereof to cool down.
• CAUTION:   Do not use the appliance with a program, time switch or any other part that turns the appliance on automatically as there is a risk of fire if the appliance is not covered or placed properly.
• WARNING : Some parts of this product may become very hot and cause burns. During operation, the appliance produces hot water and hot steam under pressure. Special attention must be paid to the presence of children and handicapped people.
• WARNING, HOT STEAM:   pay extra care when you are using the milk frother and do not touch it until it has cooled down. Bear in mind that hot water might spurt out for a short time during use. Do not touch the metal part of the nozzle during use; use only the plastic part of the milk frother cover A4 to make adjustments.
• For hygienic reasons, clean the steam nozzle by flushing it after each use. After cooling, remove the outer part (tube) and rinse it with lukewarm water.
• When the appliance is in operation, prevent pets, plants or insects to get in contact with it.
• Do not plug the fork of the supply cord into the power outlet and do not unplug the cord with wet hands or by pulling by the supply cord!
• Prevent injuries when handling (e.g. by hot water, steam).
• Never immerse the appliance or its cord (or parts thereof) in water.
• Never transfer the appliance when there is water in the tank! Water might leak into the internal components.
• Never leave the appliance unattended when it is connected to the mains and keep an eye on it the whole time you are making your espresso!
• When transferring the appliance, take it by the outer casing only.
• Leave a space of at least 15mm from all sides of the appliance to ensure proper circulation of air.
• Do not expose the appliance to temperatures under 4°C – if residual water froze in the internal components, it could damage the appliance.
• Use this appliance only for the purpose for which it was designed as specified in this user‘s manual. Never use the appliance for any other purpose.
• The producer is not responsible for damage caused by improper use of the appliance
  (e.g. burning, scalding, fire) and its guarantee for the appliance does not apply to situations when the safety warnings above are not complied with.

USE OF THE APPLIANCE:

• The appliance is intended for home use and similar (in shops, offices and similar workplaces, in hotels, motels and other residential environments, in facilities providing accommodation with breakfast). It is not intended for commercial use!
• If you are not going to use the appliance for a longer time, empty the water tank! If you do not brew coffee frequently, replace the water in the water tank regularly (preferably every day) so as to keep it fresh at all times.
• Use cold (lukewarm) clean water only! Never use hot water or other liquids – they could damage the appliance.
• Do not use the hot water feature longer than it takes to use up the capacity of one water tank.
• Use the appliance in the working position only at flat and stable places with no risk of turning over and in sufficient distance from heat sources (e.g. heater, stove, cooker, oven, grill), flammable objects (e.g. curtains, drapes, etc.) and wet surfaces (e.g. sinks, washbasins, etc.).
• Do not place the appliance near objects or under objects which could get damaged by steam, e.g. walls, kitchen cupboards, sideboards, paintings, or curtains. Leaking steam could damage them.
• Do not use the appliance in an environment saturated with explosive or flammable steams.
• Before switching on the appliance ensure that the water level is between MIN and MAX marks.

POWER CORD:

• If the power cord of the appliance is corrupted, it has to be replaced by the manufacturer, its service technician, or a similarly qualified person so as to prevent dangerous situations.
• Never use the appliance if its power cord or plug is damaged, if it does not work properly, if it fell down and was damaged or if it fell to the water. In this case, take the appliance to a special service to check its safety and proper function.
• The power cable supplied with the appliance is designed solely for this appliance – never use it for any other purposes. Also, this appliance may only be used with the power cable included in the box. Never use any other cable type (e.g. for a different appliance).
• Never put the power cord on hot surfaces or do not let it hang over the edge of a table or a worktop. Plugging or pulling the power cord e.g. by children can result in tilting over or drawing the appliance down and serious injury!
• The power cord must not be damaged with sharp or hot objects, open fire, it must not be sunk into water or bent over sharp edges.

DESCRIPTION OF THE APPLIANCE

A – The machine body

• A1 – main ON / OFF switch
• A2 – heating surface
• A3 – milk frother (steam nozzle)
• A4 – milk frother cover
• A5 – metal tube
• A6 – power cord

B – Control panel

• B1 – steam nozzle button
• B2 – button for two cups
• B3 – button for one cup
• B4 – rotary knob for setting functions

C – Metal lever with plastic handle

• C1 – funnel
• C2 – stainless steel bowl for one cup
• C3 – stainless steel bowl for two cups
• C4 – auxiliary handle preventing falling out of the bowl when emptying the coffee grounds

D – Water tank

E – Drip tray

• E1 – drip grille

F – Coffee measuring cup with stamper

PREPARATION FOR USE

Before first use, remove any packaging and protective material (including any protective film) from the appliance and accessories. Wash the water tank D with warm soap water, rinse it with clean water and allow it to dry. Put it into the coffee machine again and press it down as far as it goes.

Location
Place the coffee machine onto a flat and stable surface, near a socket. Keep a minimum distance of 15cm from any wall at all sides.

Filling the tank with water
Remove the D tank from the coffee machine and fill it with water, preferably at room temperature (the water level must be between the MIN and MAX marks). Then put the tank back in place.

Removing operational components
Looking at the camera that is used more often with the coffee machine (metal lever C, drip tray E), proceed as shown in Fig. 1, 2. Proceed in reverse order to put the components back.

Rinsing the coffee maker
At the first start-up or if you have not used the coffee machine for more than 2 days, flush it using the following procedure:

1. Fill tank D with water up to the MAX mark.
2. Place lever C and the stainless-steel bowl (C2/C3) on the coffee machine as shown in Figure 2.
3. Connect the coffee machine to the el. mains, set the rotary knob B4 to the „“ position and switch on the coffee machine by turning the switch A1 to the „I“ position. The backlight of the buttons starts flashing (the coffee machine is warming up). After warming up, the backlight buttons will be permanently lit.
4. Once the coffee machine has warmed up, turn control B4 to the „“ position and then press button B2/B3 and let hot water flow through the coffee machine.
5. To flush the steam wand, in standby mode, turn the knob B4 to the „“ position (only the backlight of button B3 will be lit) and then press button B3 (hot water function). To end the flush, press button B3 again.

Note: When flushing out the coffee machine, collect the water into the drip tray E or into a suitable cup. Empty the drip tray regularly

USING THE APPLIANCE

Remarks: When making coffee, the coffee machine automatically has a coffee brewing function that cannot be switched off.

PREPARATION OF ESPRESSO

1. Turn the B4 knob to the „“ position and switch on the coffee machine by turning the switch A1 to the „I“ position and wait for it to warm up (the backlight of the buttons will be permanently lit).
2. Place the stainless-steel bowl (C2/C3) in the funnel C1 of lever C.
3. Fill the stainless-steel bowl (C2/C3) with ground coffee to the brim with a measuring cup F. Smother the coffee properly with the stamper (back of the measuring cup F) intended for this purpose.
4. Place the lever C on the coffee machine as shown in Fig. 2.
5. Place a suitable size cup / cups under the coffee spout.
6. Turn the B4 knob to the „“ position and then press button B2 or button B3.
7. Wait for the coffee to finish.

Cup preheat

• For an optimum coffee making process and better taste of your coffee, we recommend that you preheat your cup by filling it with hot water first (e.g. using the hot water function). After the cup has been preheated, pour the water away.
• You can use the heating surface A2 to warm up the cup for your coffee.

MAKING CAPPUCCINO, CAFFÈ LATTE AND ESPRESSO MACCHIATO
The steam nozzle A3 is designed for making espresso beverages containing milk and milk froth. For superior taste and quality of the beverage, use chilled fresh whole milk only.

Recommended procedure

1. Fill a container with milk. The container must be sufficiently large as the milk quantity will increase three times as much.
2. Firstly, make coffee following the usual procedure as the use of the steam nozzle will increase the temperature in the internal system, which could burn the ground coffee if you proceeded in reverse order. EN 23 / 51
3. Activate the steam nozzle by pressing button B1. Nozzle heating is indicated by blinking the backlight of button B1. When the nozzle is ready, the backlight of button B1 is permanently on. Turn regulator B4 to „“ and steam nozzle A3 will produce steam.
4. Then place the milk container under the steam nozzle so that the nozzle opening slightly touches the milk level and let the steam flow into the milk slowly by turning it counterclockwise. Switch off the steam wand by pressing the B1 button again or turning the B4 control to the „“ position.
5. Pour the frothed milk carefully over the coffee based on the espresso beverage you have selected; you can use a teaspoon to do so.
6. Make sure to clean the milk frother immediately after use (components A3, A4, A5) see chapter MAINTENANCE (for basic fast cleaning we recommend that you activate the steam nozzle again for a short time). Milk-caked frother is harder to clean.

Recommendation

• For optimum micro-froth production, we recommend that you use a special milk pot intended for that purpose.
• Another way to make micro-froth (but not larger dense froth) is to tilt the container at a slight angle, not move it and allow the steam to stream into the container, creating an eddy.

INDIVIDUAL INSTALLATION OF COFFEE QUANTITY

The amount of coffee can be adjusted both for two cups (25-200 ml – button B2) and for one cup (25-100 ml – button B3). The procedure is as follows:

1. Turn the B4 knob to the „“ position and switch the coffee machine on by turning the A1 switch to the „I“ position and wait for it to warm up (the backlight of the buttons will be permanently lit).
2. Turn the B4 knob to the „“ position.
3. Then press and hold the B2/B3 button until the desired quantity of coffee flows out. When the desired amount of coffee is flowing, release the button.
4. The setting will be saved in the coffee machine memory and will remain stored even after the coffee machine is switched off and unplugged. network.

Remarks

• If you hold the B2/B3 button too short, your settings will not be saved.
• Make the following steps to return to factory setting:
  • Be sure the coffee machine is connected to electricity supply.
  • Turn rotary switch B4 to „“.
  • Set the main switch A1 to position ‟O“(off).
  • Press and hold simultaneously buttons B1 and B3, and at the same time, set the main switch A1 to position ‟I“(on).
  • Then release buttons B1 and B3.
  • Signal lamps of buttons B2 and B3 start flashing blue alternately.
  • Use main switch A1 to switch the coffee machine on, and then off.
  • Turn rotary switch to „“.
  • Signal lamps of buttons B1 and B2 will be flashing blue and signal lamp of button B3 will be flashing blue and red.
  • Then press button B3 and wait until the signal lamps of all buttons start flashing blue. In this way, factory setting has been restored and the coffee machine can be normally used.

HOT WATER FUNCTION

1. Set the rotary knob B4 to the „“ position and switch on the coffee machine by turning the switch A1 to the „I“ position.
2. In standby mode, turn the knob B4 to the „“ position (only the backlight of button B3 will be lit) and then press button B3.
3. Hot water will flow out of the steam nozzle A3. Once the required amount of hot water has flowed out, press button B3 again to end the function. Then turn the B4 knob to the „“ position.

Remark
If the “Hot Water” function is used previously, a small amount of water will flow out of the nozzle at the beginning of this program. This is a normal condition.

COFFEE MACHINE COOLING
If you wish to use the coffee machine to make espresso immediately after using the steam wand, it is recommended to cool the coffee machine first because the temperature inside the coffee machine is too high. To do this, let one coffee cycle run (button B2/B3) idle. Then you can prepare espresso as standard again.

MAINTENANCE
Unplug the appliance from power supply by taking the fork of the power cord out of the socket (except for operations which require the coffee machine to remain switched on)! Clean the appliance only when it is cooled down! Do not use rough and aggressive detergents (e.g. sharp objects, scrapers, diluting agents or other solvents)! Wipe the surface of the appliance and its inlet with a damp cloth.

IMPORTANT
Regularly inspect and clean all parts to prevent mould on coffee residues!

Water tank (D)
We recommend that you clean the tank thoroughly and regularly (about once a week). Use regular washing-up liquid and then rinse the tank with clean water (you can also use a dishwasher). So as to prevent build-up of scale deposits, we recommend that you also rinse the tank under running water once a day.
Metal lever with plastic handle (C)
Remove coffee grounds from the stainless steel bowls (C2 and C3) after each use. Rinse the funnel C1 thoroughly under running water. Wash the filters (C2 and C3) in warm water with detergent and then rinse with clean water. Wipe the plastic handle with a damp cloth. Then let everything dry.
Drip tray (E)
Pour the drip tray as required. Wash parts E and E1 with a conventional dishwashing detergent, rinse with clean water and allow to dry.
Steam nozzle (A3)
The nozzle must be cleaned after each use. You can do so by activating it and immersing it in a container of clean water and then wiping it with a dry tissue. Also, clean it regularly by removing the parts. Rinse the components under running water, let them dry and proceed in reverse order to assemble and place them back. If necessary, clean the openings with a long narrow object (toothpick, needle, etc.).
Descaling
If the coffee preparation time is significantly prolonged, the coffee machine‘s water system must be cleaned of lime and mineral deposits (scale). Said deposits may be removed with a water solution with a formulation intended for this purpose (e.g. ETA518000201). Always follow the manufacturer‘s instructions for the product, which are usually on the packaging. Depending on the water hardness and the frequency of use of the coffee machine, remove scale regularly (recommended at least once a month). The procedure is as follows:

• Fill tank D with the prepared cleaning solution.
• Position lever C correctly.
• Place a suitable container under the coffee spout.
• Turn the B4 knob to the „“ position and switch the coffee machine on by turning the A1 switch to the „I“ position and wait for it to warm up (the backlight of the buttons will be permanently lit).
• Then turn the B4 knob to the „“ position.
• Press button B2/B3 to allow the cleaning solution to flow through the coffee machine‘s internal system (approx. 1/2 of the volume of tank D).
• Then turn the B4 knob to the „“ position.
• Press button B3 and use the rest of the solution to clean the steam nozzle using the hot water function.
• When container D is empty, rinse it with clean water. Then fill D-tank only with clean water and repeat the procedure. This will thoroughly flush out the inside of the coffee machine from the cleaning solution.

Expert service must do the large maintenance or to intervene into inside parts of the appliance! Non-observance of the instructions of the manufacturer cancels the right for guarantee repair! If you are unable to fix the problem, or if you need any further information about the appliance or service centres, please contact your distributor.

ENVIRONMENT
Printed signs of materials used for manufacture, packing, components and accessories, as well as their recycling, are on all the pieces if their dimensions enable it. The symbols on the product or in the accompanying documentation mean that the used electric or electronic products must not be disposed together with municipal wastes. Please, hand them over to the collection points designed for their correct disposal, where they will be accepted free of charge. By correct disposal of this product you can help to preserve valuable natural resources and help to prevent possible negative impacts to the environment and to human health, which could be the results of incorrect waste disposal. For further details ask the municipal authorities or the nearest collecting point. Penalties can be charged for incorrect disposal of such wastes, according to national regulations. If the appliance is to be put out of operation definitely, we recommend cutting off the feeder cable, to disable its use

VII. TECHNICAL DATA

Voltage (V) shown on the type label of the appliance
Absorbed power (W) shown on the type label of the appliance
Max. volume (l) 0.9
Weight (kg) approximately 2.9
Protection class of the appliance I.
Size (cm): 28.5 x 20.2 x 35.5
Input in off mode is 0,00 W
The manufacturer reserves the right to change the technical specifications and accessories for the respective models.
WARNINGS AND SYMBOLS USED ON THE APPLIANCE, PACKAGING OR IN THE INSTRUCTIONS MANUAL:

HOUSEHOLD USE ONLY; DO NOT IMMERSE IN WATER OR OTHER LIQUIDS; TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.

The symbol indicates a WARNING.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>