eufy D605 Pet Dog Camera User Guide
- June 6, 2024
- Eufy
Table of Contents
QUICK START GUIDE
Dog Camera D605
Anker Innovations Limited. All rights reserved. of Pet and eufy Pet Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners. 51005002903 V3
PRODUCT OVERVIEW
-
Treat Container Lid
-
Camera
-
Speaker
-
Microphone
-
Treat Launching Port
-
Residue Lid
-
Status LED
·Blue: Connected.
·Flashing red: Disconnected.
·Flashing blue: Connecting / Someone is watching live video / Recording a video.
·Green: Starting or restarting the system.
·Green for 10 seconds: Launching treats. -
Treat Container
-
SYNC Button
-
Release Button: Press and hold to take out the treat container.
POWERING
DOG CAMERA D605
Connect Dog Camera D605 to power with the power port on the bottom.
ADDING TO EUFY PET APP
-
Download and install the eufy Pet app, then sign up for an account.
-
Scan the QR Code on the bottom using the eufy Pet app and follow on-screen instructions to complete the setup.
REGULAR MAINTENANCE
- Clean treat container regularly.
- Remove residue regularly: remove the lid and pour out residue.
NOTICE
The adapter shall be installed near the equipment and shall be easily
accessible. Do not use the Device in the environment at too high or too low
temperature, never expose the Device under strong sunshine or too wet
environment. The suitable temperature for the product and accessories is 0°C
to 40°C (32°F to 104°F).
When supplying, please place the device in an environment that has a normal
room temperature and good ventilation.
It is recommended to supply the device in an environment with a temperature
that ranges from 5°C~25°C (41°F to 77°F).
Please ensure to use only the adapter offered by the manufacturer. Using an
unauthorized adapter may cause danger and violate the authorization of the
project and the guarantee article.
This adapter is for indoor use only. The rated output voltage/current of the
adapter is 12VDC/2A. The plug of the adapter is considered as a disconnect
device.
Your product is designed and manufactured with high-quality materials and
components, which can be recycled and reused.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The
device can be used in fixed / mobile exposure conditions. The min separation
distance is 20 mm.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 10900 NE 8TH ST, STE 501, BELLEVUE, WA 98004
Telephone: 1-800-988-7973
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>