TRUSTECH KPT-173ND Indoor Electric Space Heater Instruction Manual

TRUSTECH KPT-173ND Indoor Electric Space Heater Instruction Manual

Important Safety Instructions

Please read this guidance carefully before using your fan heater, so that you can use it correctly. Please keep well with this guidance.

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons.

WARNING: POTENTIAL ELECTRICAL HAZARD IF NOT ADHERED TO.

1. This heater must be plugged into a 120V, 15amp (or more) circuit of its Do not plug anything else into the same circuit. If unsure if your home meets this specification, consult a certified electrician before use. Risk of fire, overheating, malfunction, property damage, injury, or even death may result if not adhered to!
2. Plug the heater on a properly grounded outlet only. Do not plug it on extension cords, surge protectors, timers, direct breakers, or an outlet with other appliances connected to the same There are risks of fire, overheating, malfunction, property damage, injury, or even death that may result if not adhered to!
3. The heater surface is hot when in To avoid burns, do not touch the heater surfaces with your hands.
4. Keep the combustible materials (furniture, pillows, bedding, papers, clothes, and curtains) at least from the front of the heater and keep them away from the sides and back of the heater.
5. Extreme caution is necessary when the heater is used by children, invalids, pets, or the heater is left operating
6. Always unplug the heater when not in use.
7. Do not use the heater with any damage, such as a worn cord or plug, or any heater with malfunctions after been Please contact the seller for resolution options.
8. Do not use the heater Exposure to outdoor elements such as rain, snow, sun, wind, or any extreme temperatures may cause a safety hazard.
9. This heater is not intended for use in bathrooms, laundry areas, or moisture indoor locations, or any extended outlets.
10. Never place the heater where it may fall into a bathtub or other water receptacles.
11. Do not run the cord under the Do not cover the cord with throw rugs, runners, or similar coverings. Arrange the cord away from traffic areas and where it will not be tripped over.
12. The heater must be plugged into a wall outlet that is a dedicated circuit with a minimum 15amp rating on that individual l circuit
13. To disconnect the heater, first, switch the power button to the OFF status, then you can remove the plug from the wall outlet.
14. Do not let any objects enter or block any ventilation or exhaust opening as this may cause electric shock, fire, or damage the heater.
15. Leave at least 3 ft. of unobstructed space to the front and rear of the heater to allow for maximum heat, air, and ventilation flow.
16. Inner parts of the heater might slightly hot arcing or sparking. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored, nor use flammable solvents to clean the heater. Keep the heater dry at all times.
17. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
18. Do not use abrasive solvents to clean the heater, in case it causes any damage to the finish or casing.
19. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use it on any soft surfaces, like a bed or carpet where the opening may become blocked.
20. Always plug heaters directly into a wall outlet/receptacle. Never use an extension cord or relocatable power tap (outlet/power strip).
21. Do not unplug the heater when the unit is still ON, as the vent grill will be hot.
22. Shut off the switch of the heater and wait 10 minutes before unplugging from the wall.

Safety Protection Feature

Overheating Protection

This heater is equipped with an overheat safety feature. When the internal components of the heater reach a certain temperature that could cause overheating or possible fire, the heater will automatically shut off. If the heater has been overheated, you will need to unplug the heater from the wall and re-plug it to use the heater again.

Tip-Over Protection

This heater is equipped with a tip-over switch on the bottom. When the heater is tilted or the base is off the ground, the heater will automatically shut down. We recommend that you place the heater on a flat floor or desk, and do not put it on an uneven carpet which may trigger the tip-over switch.

Thermostat Function

This heater is equipped with a thermostat, which allows you to control the temperature. It will get the heater automatically adjust according to your Set temperature and the Environment temperature. For example, if the Environment temperature is 82℉:
a. When the Set temperature(80℉) is equal to or lower than the Environment temperature, the appliance will stop heating and turn to fan mode.
b. When the Set temperature(85℉) is higher than the Environment temperature, the appliance will turn to low heat mode.
c. When the Set temperature(90℉) is higher or equal to the Environment temperature+5℉ or +6℉, the appliance will turn to high heat mode.

Note: ℉ display will be ±1℉ deviation.

Cautions

WARNING: TO PREVENT ELECTRICAL SHOCK, MATCH THE WIDE BLADE OF THE PLUG TO THE WIDE SLOT OF THE RECEPTACLE AND FULLY INSERT.

WARNING: It is normal for the power cord to get hot at work. However, a poor connection or loose fit between the outlet and the plug may cause overheating of the plug. If this occurs, try inserting the plug into a different outlet. Contact a qualified electrician to inspect the original out letf or damage.

Technical Parameters

Usage

1. Please check before you use:
   a. The heating element and electric wire are NOT broken. b. Please do not use the socket lower than 15A for fear of any accident.

2. Use the fan heater in the flat place to avoid being toppled.

3. If you stop using the heater, turn off the power switch, then put off the plug.

4. If you want to move the heater, please turn off the switches, then put off the plug

Using Methods

KPT-173ND Turn on the power switch in the back first, “O”= OFF，“—”ON；

1. Turn on the power switch in the back, LED display “–”, the appliance is standby; See picture 1.1

2. . Press “ ”as follows: ON (only Fan working), LED display Environment temperature(default is ℉ after the power cut off); OFF(Fan will keep working for 30 seconds when shutdown the appliance after heating)；See picture2.1

3. Press “ ”, low heat(1000W), high heat(1500W), FAN working, Seepicture3.1-3.2

4. Press “ ” to set a timer, 1h、2h…..12h; See picture 4.1-4.4

5. Press “ ”, SWING ON, SWING OFF, See picture 5.1

6. Press “ ” to set temperature, Temperature range: 50-95℉；see picture 6.1-6.2
   Press over 3s, switch to ℃, Temperature range: 10-35℃, See picture 6.3-6.4. Press over 3s again, switch to ℉. (The remote control can not switch the Temperature unit, only can switch on the machine.)

7. The operation method of the remote control is the same
   Note: The indicator lights when the corresponding function is working.

Maintenance

1. Please make sure the plug should be pulled out BEFORE cleaning the heater.
2. Strictly prohibit washing the radiator by water, it can be cleaned by a piece of soft damp cloth with a little neutral detergent. Please do not use other solvents like gasoline.
3. The fan heater must be used or stored after cooled and dried completely.
4. If stop using the heater, please pull out the plug from the socket, and store it in the dry place with a rust-proof polybag, original packing is favored.

Warranty Information

The manufacturer provides a warranty under the legislation of the customer’s own country of residence, with one year warranty, starting from the date on which the appliance is sold to the end-user. The warranty only covers defects in material or workmanship. The repairs under warranty may only be carried out by an authorized service center. When claiming the warranty, the original bill of purchase (with purchase date) must be submitted. The warranty will not apply in cases of:

• Normal wear and tear
• Incorrect use, e.g. overloading of the appliance, use of non approved accessories
• Use of force, damage caused by external influences
• Damage caused by non-observance of the user manual, e.g. connection to an unsuitable mains supply or non-compliance with the installation instructions
• Partially or completely dismantled appliance

After-Sales Service

Thank you for supporting our product.

We provide a 12-month warranty to every customer.

For any questions or concerns, please contact us at below email along with the model number: KPT-173NDandyour order number, we will give you a satisfactory solution:
support@trustechproducts.com

Or scan the QR code for 24-hour online after-sales service.

Scan to get vip service

https://trustech.afterservice.vip

Scan to get vip service

https://trustech.afterservice.vip

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>