milwaukee M12 T LED Tourch without Battery and Charger User Manual
- June 6, 2024
- Milwaukee
Table of Contents
OPERATOR’S MANUAL
Cat. No.
M12 T LED, M18 T LED
M12 / M18 LED Work Light
WARNING
To reduce the risk of injury, a user must read and understand the operator’s
manual.
IMPORTANT SAFETY INSTRUCTIONS
WARNING READ AND UNDERSTAND ALL INSTRUCTIONS. When using electric appliances, basic precautions should always be followed, including the following:
WARNING Do not charge non-rechargeable batteries.
Before using the work light, read this operator’s manual, your battery pack
and charger operator’s manual, and all labels on the battery pack, charger,
and work light.
-
To reduce the risk of injury, close supervision is necessary when any appliance is used near children.
WARNING The lens gets very hot during use. To reduce the risk of burns, do not touch hot lenses. -
Store idle work light out of reach of children. Warm work lights can become hazardous in the hands of children.
-
Do not use outdoors.
-
Batteries must be recharged only with the charger specified by MILWAUKEE ®. A charger that may be suitable for one type of battery may create a risk of fire when used with another battery.
-
Use work light only with specifically designated battery pack. The use of any other batteries may create a risk of fire.
-
When the battery pack is not in use, keep it away from metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns, or a fire.
-
Maintain labels and nameplates. These carry important information.
-
The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similarly qualified person.
SAVE THESE
INSTRUCTIONS
SPECIFICATIONS
Cat. No. …………………… M12 T LED / M18 T LED
Volts……………………………………….. 12V / 18 V DC
Watts …………………………………………. 4 W / 3.7 W
Charger Type……………………………………… M18™
Use only MILWAUKEE® M12 or M18 Li-Ion battery packs.
ADDITIONAL BATTERY SAFETY RULES
WARNING
To reduce the risk of fire, personal injury, and product damage due to a short
circuit, never immerse your tool, battery pack, or charger in fluid or allow
fluid to flow inside them. Corrosive or conductive fluids, such as seawater,
certain industrial chemicals, bleach or bleach-containing products, etc., can
cause a short circuit.
WARNING
Do not charge non-rechargeable batteries.
SYMBOLOGY
| Warning
---|---
V
| Volts
| Direct Current
| Read Operator’s Manual
| Indoor use
| Do not stare into the light.
| Class III protection
| Regulatory Compliance Mark (RCM). This product meets applicable
regulatory requirements.
| Do not dispose of electric tools together with household waste material. Electric tools and electronic equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
FUNCTIONAL DESCRIPTION
ASSEMBLY
WARNING
Recharge only with the charger specified for the battery. For specific
charging instructions, read the operator’s manual supplied with your charger
and battery. Inserting/Removing Battery Pack Insert the battery pack by
sliding the battery pack into the body of the tool. Insert the battery pack
until the battery latches lock. To remove the battery pack, press in both
battery latches and slide the battery pack off of the tool.
WARNING
To reduce the risk of injury, do not look directly into the light when the
work light is on.
Adjusting the Pivot Head
M 12 T LED – The pivoting head can pivot to a range of 90°; with detents
every 15°. Pivot head to the desired position. Allow the detent to snap into
place. Do not forcibly pivot the head.
M18 T LED – The pivoting head can pivot to a range of 135°; with detents
every 10°. Pivot head to the desired position. Allow the detent to snap into
place. Do not forcibly pivot the head.
OPERATION
To turn on the work light, press the ON/OFF button. To turn off the work
light, press the ON/OFF button again.
Hook M18 T LED
To use the hanging hook, press in the hook joint. Pull the hook out.
MAINTENANCE
WARNING To reduce the risk of injury, always unplug the charger and
remove the battery pack from the charger or tool before performing any
maintenance. Never disassemble the tool, battery pack, or charger. Contact a
MILWAUKEE ® service Maintain Work Light facility for ALL repairs. Keep your
work light, battery pack, and charger in good repair by adopting a regular
maintenance program. If the work light does not work properly, return the work
light to a MILWAUKEE ® service facility for evaluation and repair.
Cleaning
Keep tool handles clean, dry, and free of oil or grease. Use only mild soap
and a damp cloth to clean the tool, battery pack, and charger since certain
cleaning agents and solvents are harmful to plastics and other insulated
parts. Some of these include petrol, turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents, ammonia, and household detergents
containing ammonia. Never use flammable or combustible solvents around tools.
ACCESSORIES
WARNING
Always remove the battery pack before changing or removing accessories. Only
use accessories specifically recommended for this tool. Others may be
hazardous.
For a complete listing of accessories, refer to your MILWAUKEE® Electric Tool
catalogue or go online to milwaukeetool.com.au
/ milwaukeetool.co.nz or contact a distributor.
To obtain a catalog, contact your local distributor or a service center.
WARRANTY – AUSTRALIA and NEW ZEALAND
Please refer to Australian and New Zealand warranty supplied with the tool. This warranty applies only to products sold by authorized dealers in Australia and New Zealand.
SERVICE – AUSTRALIA and NEW ZEALAND
MILWAUKEE® prides itself in producing a premium quality product that is
Nothing But Heavy Duty™ Your satisfaction with our products is very important
to us! If you encounter any problems with the operation of this tool, please
contact your authorised MILWAUKEE® dealer. K
For a list of MILWAUKEE® dealers, guarantee or service agents please contact
MILWAUKEE® Customer Service or visit our website. (Australia Toll Free
Telephone Number 1300 645 928) (New Zealand Toll Free Telephone Number 0800
645 928) or visit
milwaukeetool.com.au/milwaukeetool.co.nz.
Milwaukee Electric Tool Corporation
13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005
Milwaukee Tool (Australia)
26 – 40 Nina Link, Dandenong South,
Victoria, 3175, Australia
Milwaukee Tool (New Zealand)
274 Church Street, Penrose,
Auckland, 1061, New Zealand
DESIGNED BY MILWAUKEE ELECTRIC TOOL CORP.
PROFESSIONALLY MADE IN CHINA
PRINTED IN CHINA
961011193-03(A)