SEALEY LEDWC02 5W + 3W COB LED Inspection Lamp Wireless Rechargeable Instructions
- June 6, 2024
- SEALEY
Table of Contents
SEALEY LEDWC02 5W + 3W COB LED Inspection Lamp Wireless Rechargeable
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
GENERAL SAFETY
Ensure the lamp is fully charged before initial use.
- DO NOT turn the lamp on when it is being charged.
- DO NOT shine directly into your, another person’s or an animal’s eyes.
- DO NOT allow children to use the lamp.
- DO NOT handle or move the lamp whilst it is being charged.
- DO NOT use the lamp if you suspect that the battery or the lamp casing is damaged.
- DO NOT leave battery in a discharged state, recharge battery immediately. Before storage, fully recharge the battery, subsequently recharge the battery at least once every six months of non-use.
BATTERY SAFETY
WARNING! To reduce the risk of burns or fire:
- DO NOT attempt to open, disassemble, modify or service the battery pack.
- DO NOT crush, puncture, short external contacts or dispose of in fire or water.
- DO NOT expose to temperatures above 60°C (140°F).
Recycle or dispose of used battery as stipulated by local regulation.
INTRODUCTION
Heavy-duty inspection lamp with dimming function. Supplied with one strong magnet on the base and two on the back. Lumen output on side lamp 50-500lm with dimming function and 300lm on top light. Operating time is 3-10hr on side lamp and 5hr on the top light. Charging time is 5hr. Includes LED indicator for level of charge on the front of the torch. Charger not included, compatible with Model No’s WCB1 and WCB2 Wireless Charging Bases.
SPECIFICATION
- Model No: ……………………………………………………. LEDWC02
- Battery ……………………………………………………3.7V 2600mAh
- Charging Time …………………………………………………………5hr
- IP Rating ……………………………………………………………….IP68
- LED Qty …………………………………………………………………..24
- Lumen outputs ………………………Side; 50-500lm, Top; 300lm
- Operating time …………………….3-10hr/5hr – 50-500lm/300lm\
IMPORTANT WARRANTY INFORMATION
The battery fitted to this lamp is considered to be a consumable item and its
ability to accept a charge will reduce over time.
We will provide warranty against mechanical and electrical defect for a period
of one year – this DOES NOT cover fair wear and tear. If the battery is not
properly charged before first use, or regularly conditioned, its capacity will
diminish. Under these circumstances we will not replace the item regardless of
whether it is less than one year old.
OPERATION
CHARGING THE LAMP
Rest the lamp on the charging platform such that the wireless charging pad on
the torch lies directly above the charge pad on the platform.
The left hand RED LED on the torch will illuminate and the GREEN LEDS to its
right will light or flash depending on the state of the battery. A solid green
LED indicates that the torch is charged to that level, a flashing green LED
indicates that the torch is charging. When fully charged all three green LEDs
and the red LED will be lit.
OPERATING THE LAMP
The
lamp ON/OFF/FADE button is located on the side of the lamp (fig.2). The
operation sequence is: one press for top LED, second press turns front lamp on
and top lamp off. A third press that is held on, causes front lamp output to
decrease. Press and hold once more and the lamp output will increase. To turn
the unit off, one further short press of the switch is required.
The battery state LEDs turn off after approximately 1 minute after turning the
lamp on. When the charge is 25% the red LED will flash. The lamp may be
suspended by the hook on rear of lamp or attached to any ferrous surface by
using the magnets on the back of the torch or the magnet in the base.
MAINTENANCE
Keep the torch clean by wiping with a damp cloth.
Store torch in a dry childproof area.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the
EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the
product is no longer required, it must be disposed of in an environmentally
protective way. Contact your local solid waste authority for recycling
information.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>