ELATEC TWN4 Palon Compact Legic M User Manual
- June 6, 2024
- ELATEC
Table of Contents
TWN4 PALON COMPACT
LEGIC M
USER MANUAL
INTRODUCTION
1.1 ABOUT THIS MANUAL
This user manual is intended for the user and enables safe and appropriate
handling of the product. It gives a general overview, as well as important
technical data and safety information about the product. Before using the
product, the user should read and understand the content of this user manual.
For the sake of better understanding and readability, this user manual might
contain exemplary pictures, drawings, and other illustrations. Depending on
your product configuration, these pictures might differ from the actual design
of your product.
1.2 ELATEC SUPPORT
In case of any technical questions, refer to the ELASTIC website
(www.elatec.com) or contact ELASTIC technical support
at: support-rfid@elatec.com
In case of questions regarding your product order or if you wish additional
copies of this user manual, contact your Sales representative or ELASTIC
customer service at:
info-rfid@elatec.com
1.3 REVISION HISTORY
VERSION | CHANGE DESCRIPTION | EDITION |
---|---|---|
01 First edition | Aug-21 |
INTENDED USE
TWN4 Palon Compact LEGIC M is a versatile OEM PCB for integration into third-
party products and devices. It supports enhanced interfaces, especially
RS-485. The new compact PCB module inherits all advantages and integrated tool
support of the ELASTIC TWN4 family. Although it is a general-purpose device,
it is optimized for time attendance and access control.
The product is intended to be integrated into a host device.
Any use other than the intended use described in this section, as well as any
failure to observe the safety information listed in this document, will be
considered misuse and will void the warranty. RELATED is not responsible for
any damage or injuries resulting from any misuse of the product.
SAFETY INFORMATION
Installation
-
The installation of the product should be done by trained and qualified personnel only. Do not install the product by yourself.
-
Metallic materials on or in direct vicinity to the product might reduce the reading performance of the product. In some circumstances, plastic screws should be preferred to metallic screws when installing the product. Refer to the installation instructions or integration manual of the product for more information.
Handling -
Depending on your product configuration, the product might be equipped with one or more light-emitting diodes (LED). Avoid direct eye contact with the blinking or steady light of the light-emitting diodes.
-
The product has been designed for use under the following conditions:
o Temperature range: -25 °C – 80 °C (operating conditions)
o Relative humidity: 5% – 95% (non-condensing)
o Integration into a host device.
Any use of the product under different conditions might damage the product or alter its reading performance. -
The use of other RFID readers or reader modules in direct vicinity to the product, or in combination with the product might damage the product or alter its reading performance. In case of doubts, contact ELATEC for more information.
-
The user is liable for the use of spare parts or accessories other than the ones sold or recommended by ELASTIC. ELASTIC is not responsible for any damage or injuries resulting from the use of spare parts or accessories other than the ones sold or recommended by ELASTIC.
-
Like most electronic devices, RFID systems generate electromagnetic waves that can vary in amplitude and frequency. It is generally known and accepted that some RFID devices might potentially interfere with personal medical devices, like pacemakers or hearing aids.
Users with a pacemaker or any other medical device should use TWN4 Palon Compact LEGIC M carefully and refer to the information given by the manufacturer of their medical devices before using TWN4 Palon Compact LEGIC M or any host device containing TWN4 Palon Compact LEGIC M. Maintenance and cleaning -
Any repair or maintenance work should be done by trained and qualified personnel only. Do not try to repair or carry out any maintenance work on the product by yourself.
Do not allow any repair or maintenance work on the product by an unqualified or unauthorized third party. -
The product does not need any special cleaning.
Do not use any detergents or other cleaning agents on the product.
Disposal -
The product must be disposed of in accordance with the EU directive on waste electrical and electronic equipment (WEEE) or other applicable local regulations.
Product modifications -
The product has been designed, manufactured, and certified as defined by ELASTIC.
Any product modifications not expressly approved by ELATEC, including – but not limited to – modifications of antennas or other radio-related components, is not allowed and will void the warranty and all approvals granted to the product.
**** If you are unsure about any part of the safety information above, contact ELASTIC support.
Any failure to observe the safety information above will be considered misuse and will void the warranty. ELASTIC is not responsible for any damage or injuries resulting from any misuse of the product.
TECHNICAL DATA
The reader module is equipped with the following antennas:
TWN4 Palon Compact LEGIC M
HF antenna (13.56 MHz)
Dimensions: 39 x 42.5 mm / 1.54 x 1,67 inch Number of turns: 3
LF antenna (125 kHz)
Dimensions: 27 x 27.5 mm / 1.06 x 1.08 inch Number of turns: 179 BLE (2.4 GHz)
The antenna for the BLE module is integrated into the BLE chip.
For more information, refer to the product data-sheet.
MODE OF OPERATION
5.1 OPERATING MODE
In order to start operating TWN4 Palon Compact LEGIC M, it simply has to be
connected directly to a host device.
5.2 POWER-UP In case of an external power supply unit is used, the following
requirements must be satisfied:
• Limited power source according to the safety norms listed in the respective
declaration(s) of conformity
• Short-circuit current < 8 A Once TWN4 Palon Compact LEGIC M is connected to
the host, it detects the type of communications cable (e.g. USB or RS-232),
with which it is connected to the host. Additionally, the RS-232 is sending a
version string via RS-232 to the host.
5.3 ENUMERATION
This is only applicable for the USB version: Once the device has been powered
up, it is waiting for completion of the enumeration by the USB host. As long
as the device is not enumerated, it is entering a minimum power consumption
mode, where both LEDs are turned off.
5.4 INITIALIZATION After powering up and enumeration (in USB mode), the device
is turning on the built-in transponder-reader logic. The green LED is turned
on permanently. Some RFID reader modules need some kind of initialization,
which is performed in this step. After successful initialization, the device
sounds a short sequence, which consists of a lower tone followed by a higher
tone.
5.5 NORMAL OPERATION
As soon as the reader module has completed the initialization, it is entering
normal operation. During normal operation, the reader module is searching for
a transponder continuously.
5.6 DETECTION OF A TRANSPONDER
If a transponder is detected by the reader module, the following actions are
performed:
- Send the ID to the host. By default, the USB device sends by emulating keystrokes of a keyboard. An RS-232 device sends the ASCII code of an ID.
- Sound a beep.
- Turn off the green LED.
- Blink the red LED for two seconds.
- Turn on the green LED.
Within the two seconds timeout, where the red LED is blinking, the
transponder, which just has been recognized will not be accepted again. This
prevents the reader module from sending identical IDs more than one time to
the host. If during the two seconds timeout of the red LED a different
transponder is detected, the complete sequence restarts immediately.
5.7 SUSPEND MODE
The USB version of the reader module supports the USB suspend mode. If the USB
host is signaling to suspend via the USB bus, the reader module is turning off
most of its power-consuming peripherals. During this operation mode, no
detection of transponders is possible and all LEDs are turned off. Once the
host is resuming to normal operation mode, this is also signaled via the USB
bus. Therefore, the reader module will resume to normal operation too.
COMPLIANCE STATEMENTS
6.1 EU
TWN4 Palon Compact LEGIC M is in compliance with the EU directives and
regulations as listed in the respective declaration of conformity.
6.2 FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Caution
The Federal Communications Commission (FCC) warns the users that changes or
modifications to the unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC §15.105 (b)
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
FCC ID: WP5TWN4F11
Contains FCC ID: QOQ11
6.3 IC
This device complies with Industry Canada’s license-exempt RSS. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and (2) This device must accept
any interference, including interference that may cause undesired operation of
the device.
IC: 7948A-TWN4F11
Contains IC: 5123A-11
6.4 RF EXPOSURE COMPLIANCE
RF exposure statement (mobile and fixed devices)
This device complies with the RF exposure requirements for mobile and fixed
devices. However, the device shall be used in such a manner that the potential
for human contact during normal operation is minimized.
APPENDIX
A – TERMS AND ABBREVIATIONS
TERM | EXPLANATION |
---|---|
BLE | Bluetooth Low Energy |
FCC | Federal Communications Commission |
HF | high frequency |
IC | Industry Canada |
LF | low frequency |
NFC | near field communication |
PCB | printed circuit board |
RFID | radio frequency identification |
WEEE | Waste of electrical and electronic equipment. Refers to Directive |
2011/65/EU of the European Parliament and of the Council of the European Union
B – RELEVANT DOCUMENTATION
ELASTIC documentation
- ELASTIC quick start guide
- TWN4 Palon Compact LEGIC M datasheet
- TWN4 Palon Compact LEGIC M integration manual
- TWN4 Palon technical handbook
ELASTIC GMBH
Zeppelinstr. 1
• 82178 Puchheim
• Germany
P +49 89 552 9961 0
• F +49 89 552 9961 129
• E-mail: info-rfid@elatec.com
elatec.com
Elatec reserves the right to change any information or data in this document without prior notice. Elatec declines all responsibility for the use of this product with any other specification but the one mentioned above. Any additional requirement for a specific customer application has to be validated by the customer himself at his own responsibility. Where application information is given, it is only advisory and does not form part of the specification. Disclaimer: All names used in this document are registered trademarks of their respective owners. © 2021 ELATEC GmbH – TWN4 Palon Compact LEGIC M user manual DocRev1 – 08/2021
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>