ELATEC RFID TWN4 Multitech 2 BLE Module User Manual

ELASTIC RFID TWN4 Multitech 2 BLE Module

INTRODUCTION

ABOUT THIS MANUAL

This user manual is intended for the user and enables a safe and appropriate handling of the product. It gives a general overview, as well as important technical data and safety information about the product. Before using the product, the user should read and understand the content of this user manual. For the sake of better understanding and readability, this user manual might contain exemplary pictures, drawings and other illustrations. Depending on your product configuration, these pictures might differ from the actual design of your product

ELASTIC SUPPORT

In case of any technical questions, refer to the ELASTIC website (www.elatec.com) or contact ELASTIC technical support at: support- rfid@elatec.com

In case of questions regarding your product order or if you wish additional copies of this user manual, contact your Sales representative or ELASTIC customer service at:  info-rfid@elatec.com

REVISION HISTORY

compliance statement for

United Kingdom added

| 07/2021

02

| Sections “Handling” updated and “Product modifications” added under chapter 3 “Safety

information”, compliance statement for Taiwan updated, compliance statement for Thailand added

|

06/2021

01

| First edition

(replaces Transponder Reader TWN4 MultiTech 2 Quick Start Guide , Rev 1.2, dated 02/2017)

|

05/2021

INTENDED USE

The TWN4 MultiTech 2 BLE reader has integrated RFID (LF & HF) and Bluetooth Low Energy (BLE), which is supported by mobile phones with Android version 4.3 or greater, iOS 8.0 or greater and PCs with Windows (new Bluetooth hardware integrated). The app on the reader communicates with the BLE module with easy commands and has a direct enhancement to the GATT structure, which gives you the flexibility to write your custom apps.N The product is for indoor use and may not be used outdoor. Any use other than the intended use described in this section, as well as any failure to observe the safety information listed in this document, will be considered misuse and will void the warranty. ELATEC is not responsible for any damage or injuries resulting from any misuse of the product.

SAFETY INFORMATION

Installation

• The installation of the product should be done by trained and qualified personnel only. Do not install the product by yourself.
• Metallic materials on or in direct vicinity to the product might reduce the reading performance of the product. In some circumstances, plastic screws should be preferred to metallic screws when installing the product. Refer to the installation instructions or integration manual of the product for more information

Handling

• Depending on your product configuration, the product might be equipped with one or more light-emitting diodes (LED). Avoid direct eye contact with the blinking or steady light of the light-emitting diodes.
•  The product has been designed for a use under following conditions:
•  Temperature range: -25 °C – 70 °C (operating conditions)
•  Relative humidity: 5% – 95% (non-condensing)
•  Indoor use – no outdoor use! Any use of the product under different conditions might damage the product or alter its reading performance.
• The use of other RFID readers or reader modules in direct vicinity to the product, or in combination with the product might damage the product or alter its reading performance. In case of doubts, contact ELATEC for more information.
• The user is liable for the use of spare parts or accessories other than the ones sold or recommended by ELASTIC. ELASTIC is not responsible for any damage or injuries resulting from the use of spare parts or accessories other than the ones sold or recommended by ELATEC.
•  Like most electronic devices, RFID systems generate electromagnetic waves that can vary in amplitude and frequency. It is generally known and accepted that some RFID devices might potentially interfere with personal medical devices, like pacemakers or hearing aids.
  Users with a pacemaker or any other medical device should use TWN4 MultiTech 2 BLE carefully and refer to the information given by the manufacturer of their medical devices before using TWN4 MultiTech 2 BLE.

Maintenance and cleaning

• Any repair or maintenance work should be done by trained and qualified personnel only. Do not try to repair or carry out any maintenance work on the product by yourself.N Do not allow any repair or maintenance work on the product by an unqualified or unauthorized third party.
• The product does not need any special cleaning. However, the housing may be carefully cleaned up with a soft, dry cloth on the outer surface only. Make sure that the used cloth and cleaning agent do not damage the product or its components (e.g. label(s)).

Disposal

• The product must be disposed of in accordance with the EU directive on waste electrical and electronic equipment (WEEE) or other applicable local regulations

Product modifications

• The product has been designed, manufactured and certified as defined by ELASTIC. Any product modifications not expressly approved by ELATEC, including – but not limited to – modifications of antennas or other radio-related components, is not allowed and will void the warranty and all approvals granted to the product.

If you are unsure about any part of the safety information above, contact ELASTIC support. Any failure to observe the safety information above will be considered misuse and will void the warranty. ELATEC is not responsible for any damage or injuries resulting from any misuse of the product.

TECHNICAL DATA

The reader is equipped with the following antennas:

PCB contained in TWN4 MultiTech 2 BLE

• HF antenna (13.56 MHz)
  Dimensions: 42 x 44 mm / 1.65 x 1.73 inch
  Number of turns: 3
  LF antenna (125 kHz)
  Dimensions: 28 x 28 mm / 1.10 x 1.10 inch
  Number of turns: 151
  BLE (2.4 GHz)
  The antenna for the BLE module is integrated in the BLE chip.
  For more information, refer to the related product data sheet or other technical documents

MODE OF OPERATION

OPERATING MODE
In order to start operating TWN4 MultiTech 2 BLE, it simply has to be connected directly to a host device.

POWER UP

• In case of an external power supply unit is used, the following requirements must be satisfied:
  • Limited power source according to the safety norms listed in the respective declaration(s) of conformity
  • Short-circuit current < 8 A

Once TWN4 MultiTech 2 BLE is connected to the host, it detects the type of communications cable (e.g. USB or RS-232), with which it is connected to the host. In case of RS-232: Additionally, the RS-232 is sending a version string via RS-232 to the hos

ENUMERATION

This is only applicable for the USB version: Once the device has been powered up, it is waiting for completion of the enumeration by the USB host. As long as the device is not enumerated, it is entering a minimum power consumption mode, where both LEDs are turned off.

INITIALIZATION

After powering up and enumeration (in USB mode), the device is turning on the built-in transponder-reader logic. The green LED is turned on permanently. Some RFID readers need some kind of initialization, which is performed in this step. After successful initialization, the device sounds a short sequence, which consists of a lower tone followed by a higher tone

NORMAL OPERATION

As soon as the reader has completed the initialization, it is entering normal operation. During normal operation, the reader is searching for a transponder continuously.

DETECTION OF A TRANSPONDER

If a transponder is detected by the reader, the following actions are performed:

• Send the ID to the host. By default, the USB device sends by emulating keystrokes of a keyboard. An RS-232 device sends the ASCII code of an ID.
• Sound a beep.
•  Turn off the green LED.
• Blink the red LED for two seconds.
• Turn on the green LED.

Within the two seconds timeout, where the red LED is blinking, the transponder, which just has been recognized will not be accepted again. This prevents the reader from sending identical IDs more than one time to the host.
If during the two seconds timeout of the red LED a different transponder is detected, the complete sequence restarts immediately.

SUSPEND MODE

The USB version of the RFID reader supports the USB suspend mode. If the USB host is signaling to suspend via the USB bus, the reader is turning off most of its power-consuming peripherals. During this operation mode, no detection of transponders is possible and all LEDs are turned off. Once the host is resuming to normal operation mode, this is also signaled via the USB bus. Therefore, the reader will resume to normal operation too

COMPLIANCE STATEMENTS

TWN4 MultiTech 2 BLE is in compliance with the EU directives and regulations as listed in the respective declaration of conformity (cf. TWN4 MultiTech 2 EC Declaration of Conformity).

FCC

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
   (1) this device may not cause harmful interference, and
   (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution

The Federal Communications Commission (FCC) warns the users that changes or modifications to the unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

FCC §15.105 (b)

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help

FCC ID: WP5TWN4F3
Contains FCC ID: QOQBGM111

IC

This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:

• This device may not cause interference; and
•  This device must accept any interference, including interference that may cause undesired operation of the device.

RF EXPOSURE COMPLIANCE

RF exposure statement (mobile and fixed devices

This device complies with the RF exposure requirements for mobile and fixed devices. However, the device shall be used in such a manner that the potential for human contact during normal operation is minimized.

UNITED KINGDOM

TWN4 MultiTech 2 BLE complies with the requirements of the UK legislations and other regulations as listed in the respective UKCA declaration of conformity.
The importer is responsible for applying the following information to the packaging of the product

UKCA marking

The importer company’s details, including the company’s name and a contact address in the United Kingdom.

APPENDIX

TERMS AND ABBREVIATIONS

Refers to Directive 2011/65/EU of the European Parliament and of the Council of the European Union

B – RELEVANT DOCUMENTATION

ELATEC documentation

• ELASTIC quick start guide
• TWN4 BLE user guide
• TWN4 MultiTech 2 technical handbook
• TWN4 MultiTech 2 BLE datasheet

Zeppelinstr. 1 • 82178 Puchheim • Germany
P +49 89 552 9961 0 • F +49 89 552 9961 129 • E-mail: info-rfid@elatec.com elatec.com

Elatec reserves the right to change any information or data in this document without prior notice. Elatec declines all responsibility for the use of this product with any other specification but the one mentioned above. Any additional requirement for a specific customer application has to be validated by the customer himself at his own responsibility. Where application information is given, it is only advisory and does not form part of the specification. Disclaimer: All names used in this document are registered trademarks of their respective owners.
© 2021 ELATEC GmbH – TWN4 MultiTech 2 BLE user manual DocRev3 – 07/2021

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>