Akuvox R20B Wall Mounting IP Video Intercom User Guide

Akuvox R20B Wall Mounting IP Video Intercom User Guide

Unpacking

Before you begin using the device, please check the version you got and ensure that the following items are included in the shipped box:

Universal Accessories:

• R2OB x 1

• Back cover x 1

•  Cable locking plate x 1

• Rope x 1

• Rubber Plug x 3 (S,M,L)

•  M2.5×6 screw x 6

• Name Pad x 20

• Pry Bar x 1

Wall-mounting Accessories :

• Wall-mounting bracket x 1

• M4x30 screw x 2

• ST4x20 screw x 4

• Plastic wall anchor x 4

• Allen Wrench x 1

• M3x6 Allen screw x 2

• Wall-mounting template x 1

• Wall-mounting screw x 4

Product Overview

Installation Environment

Indoor and outdoor installation are supported. If installing the device outdoors, please don’t place device under direct sunlight, it will bring a bad effect or be broken with the high temperature.
If installing the device indoors, please keep device at least 2 meters away from light, and at least 3 meters away from window and door .

Wall-mounting Installation

Stepl: Wall-mounting Bracket Installation

1. With embedded one-gang junction box(86×86 mm or 2×3 inches in size) in the wall.

2. Without Embedded Junction Box in The Wall
   

Step2: Back Cover Intallation

Installation Tips

Open the name pad cover with a pry bar, put the filled-in name pad in the name pad cover, and put back to close it.

Device Wiring

Application Network Topology

IP Announcement

1. While R2OB starts up normally, press 3258, voice system will enter IP announcement mode.
2. In announcement mode, the IP address will be announced periodically.
3. Press Cancel Button again to quit the announcement mode.
4. In announcement mode, phone announces “IP 0.0.0.0” if no IP address is gained.

Configuration

1. Access the Web UI: Input the IP address into web browser to configure the phone.
2. Account Registration: On web UI, go to the path: Account -> Basic page Register Account and fill in the account information. ( Please refer to user manual for more information)
3. Configure the Push Button: On web UI, go to the path: Intercom -> Basic -> Push Button to configure the call number.
4. Configure the code to open the relay: On web UI, go to the path: Intercom -> Relay -> Relay ID/DTMF and choose the DTMF code number in corresponding area.

Operation

• Make a call: Press the SIP number or IP address and dial key to make a call.
• Receive a call: R2OB supports Auto Answer by default. Incoming call will be answered automatically.
• Unlock:

1. During the talk, called party can press pre-configuredcode number to unlock the door;
2. Scan the predefined RFID card nearby the card reader tounlock;
3. Press the predefined pin code to unlock.

Indicators

Note: For more LED settings, please refer to R20B webUl: Intercom -> LED Setting.

Notice Information

Akuvox R20B firmware contains third-party open source software under the terms of the GNU General Public License(GPL). Akuvox is committed to meeting the requirements of the GNU General Public License (GPL) and will make all required source code available.

The source code of software under the terms of GNU GPL can be downloaded online: http://www.akuvox.com/gpl.

Information contained in this document is believed to be accurate and reliable at the time of printing. This document is subject to change without notice, any update to this document can be viewed on Akuvox’ s website: http://www.akuvox.com (0 Copyright 2020 Akuvox Ltd. All rights reserved.

AKUVOX (XIAMEN) NETWORKS CO., LTD. ADD:
10/F, NO.56 GUANRI ROAD, SOFTWARE PARK II, XIAMEN 361009, CHINA www.akuvox.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>