MOTION CM-06 Li-Ion Battery Powered Tube Motors With Pull and Remote User Manual

MOTION CM-06 Li-Ion Battery Powered Tube Motors With Pull and Remote User Manual

CM-06 Li-ion battery powered tube motors with pull and remote operation

Support

Video How to install, program and operate rtube.nl/red1613

WARNING

Read the instructions carefully before assembling and using the product. Assembly can be completed by nonprofessional’s. For indoor use only.

■ Young children can strangle themselves with the loop of pull cords, chains and tapes, and cords that operate window coverings. To avoid strangulation and entanglement, keep cords out of reach of young children.
■ To avoid strangulation and entanglement, keep cords out of reach of young children.
■ Cords may ensnare a child’s neck.
■ Move beds, cots and furniture away from window covering cords.
■ Do not tie cords together.
■ Make sure cords do not twist together and form a loop.

Cleaning
Follow these general rules when cleaning the outside of the device and its components:
■ Use a damp, soft, lint-free cloth. Avoid getting moisture in openings.
■ Do not use aerosol sprays, solvents, alcohol, or abrasives.

Service & Support
Do not perform repairs yourself. Do not attempt to open the device or disassemble it. You run the risk of electric shock and voiding the limited warranty. No user-serviceable parts are inside.

Warranty Service
First follow the advice in this manual. If the product appears to be damaged or does not function properly, go to your local dealer for instructions on how to obtain warranty service.

Recycle
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

Important Safety instructions
WARNING: To reduce the risk of severe injury or death, it is important to follow these instructions for personal safety. Save these instructions.

Important Installation instructions
WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury.

•  Read and follow all installation instructions.
• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children should not play with the appliance. Cleaning and user maintenance should not be performed by children without supervision.
• Do not allow children to play with fixed controls. Keep remote controls away from children.
• Frequently examine the installation for imbalance and signs of wear or damage to cables and springs. Do not use if repair or adjustment is necessary.
• This instruction manual is also available on the website.
• The drive must be disconnected from its power source during cleaning, maintenance and when replacing parts.
• The A-weighted emission sound pressure level of the drive is equal to or less than 70dB(A).
• Indoor and household use only.
• Disconnect the drive from the power supply or switch off the automatic controls when maintenance, such as window cleaning, is being carried out in the vicinity.
• When operating a biased switch, make sure that other persons are kept away.
• Do not operate when maintenance, such as window cleaning, is being carried out in the vicinity.
• The tube motor must only be supplied with safety extra low voltage corresponding to the marking on the appliance.
• Maximum operating temperature of motor is +55°C. Maximum charging temperature of battery pack is +45°C. This appliance contains batteries that are non-replaceable
• This motor can only be used with soft material for driven parts.
• Hazardous unprotected moving parts of the drive must be installed higher than 2.5m above the floor or any other level surface that could provide access to it.
• Install the actuating member of a manual release at a height less than 1.8m.
• The actuating member of a biased switch is to be located within direct sight of the driven part but away from moving parts. It is to be installed at a minimum height of 1.5m and not accessible to the public.
• The mass and the dimension of the driven part must be compatible with the rated torque and rated operating time.
• Fixed controls have to be clearly visible after installation.
• The driven part must be compatible with the rated torque 6 Nm. and rated operating time (12 min).
• Minimum tube diameter: Ø35mm.
• The drive is intended to be installed at a height of at least 2.5m above the floor or any other accessible level surface.
• All-pole disconnection switches must be incorporated in the fixed wiring in accordance with the wiring rules.
• The appliance must only be supplied at safety extra low voltage corresponding to the marking on the appliance.
• Before installing the drive, remove any unnecessary cords or components and disable any equipment not needed for powered operation.

FCC Manual | FCC ID: ZY4CM06B
Regulatory Information

1. FCC Information for User
   This product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals.

2. FCC Electronic Emission Notices
   This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference received, including interference that may cause undesired operation.

3. FCC Radio Frequency Interference statement
   This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be required to correct the interference at their own expense. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the distance separating the equipment and receiver
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

This device complies with FCC radiation exposure limits set forth for an uncontrolled rolled environment. This device should be installed and operated with a minimum distance of 20cm between the radiator and your body.

EU Declaration
Hereby, Coulisse declares that the radio equipment type CM-06 is in compliance whit directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.my.coulisse.com
Frequency range: 433 MHz, RF power:<3 dBm Frequency range BLE: 2402 – 2480 MHz, RF power: <20 dBm EIRP

1 Install your blind

2 Download the MOTION Blinds bluetooth app

Scan the QR code on your blind with the MOTION Blinds Bluetooth app to set your end limits and, once the end limits have been set, you can control your blinds with your phone. To set the end limits without your phone, please continue to step 3.

App Store Download the MOTION Blinds Bluetooth app rtube.nl/red1614

Google Play Download the MOTION Blinds Bluetooth app rtube.nl/red1615

With the MOTION Blinds bridge you can unlock more options, such as voice assistants and the ability to control your blinds when you are not at home.

App Store Download the MOTION Blinds Wi-Fi app rtube.nl/red981

Google Play Download the MOTION Blinds Wi-Fi app rtube.nl/red982

3 Find the program button on your blind

4 Activate the motor

Activate the motor by charging it with a USB C cable. A green LED will start flashing. The motor can be used during charging. To activate the motor without a USB C cable, see step 18)

5 Pair a remote

End limits must be programmed to use a blind properly and to prevent it from being damaged. Proceed to step 11 if end limits are already set.

6 Check direction of rotation

7 Set bottom position

8 Set bottom position  center

9 Set top position

10 Set bottom position

11 Set favourite position (optional)

12 De-activate program mode

13 Operate the blind

14 Operate to favourite position

15 Reset favourite position

16 De-activate direct control

When pressing the up or down button on the remote control the blind directly moves to its end positions (direct control). To operate the blind with smaller steps using the up and down button, direct control can be de-activated. Now, the blind only directly moves to its end positions when the up or down button is held longer than two seconds. The motor will also tilt slowly when using the pull function.

16.1 Press the program button on the motor to activate program mode. The blind starts stepping.
16.2 Hold the program button until the blind stops stepping (approximately 5 seconds) to de-activate or re-activate direct control.

17 Recharge the battery

Reset the blind
It is possible to only delete end limits or to do a default factory reset. A default factory reset will delete the end limits and remove the connection to any paired remote.

.1 Press the program button on the motor to activate program mode.

Delete end limits: To delete the end limits of the blind hold the program button until the blind stops stepping for the first time, keep holding the button until the blind stops stepping for the second time. (approximately 10 seconds)
Default factory reset: To reset the blind to the default factory setting hold the button for at least 20 seconds. The blind will stop stepping twice. After the second stop the blind will give one extra step to confirm the default factory reset.

Reset bluetooth

**** Hold the button 10 seconds to reset the bluetooth pairing. Any paired device will be reset.

18 Activate / deactivate the motor

To prevent the blind from getting damaged, the motor has a transport mode that makes sure the blind will not be activated before installation.

18.1 Hold the program button and pull twice to activate or deactivate the motor. The motor can also be activated by charging it with a micro USB cable.

Frequently Asked Questions

For the latest information and updated manuals visit rtube.nl/cm-06

Disclaimer:
© Copyright Coulisse
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, by any means, electronic, mechanical, photocopying, recording, digital or otherwise without the written permission of the publisher. Although this manual has been composed with the utmost care, Coulisse B.V. does not accept any responsibility for damage due to mistakes and/or faults in this manual. Coulisse B.V. reserves the right to revise the manual and to revise 19 and/or change its content at any time, without obligation to notify any person or entity of such revisions or changes. The most recent version replaces older versions of this manual. The most recent version is available at my.coulisse.com or by contacting your Coulisse contact person. We invite you to send remarks and comments about this manual to Coulisse at manuals@coulisse.com.

Coulisse B.V. Vonderweg 48 7468 DC Enter The Netherlands
t +31 547 85 55 55 f +31 547 85 55 50 e info@coulisse.com
coulisse.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>