GAZCO Liberty 85 LED Electric Fire Range Instructions
- June 6, 2024
- GAZCO
Table of Contents
- Instructions for Servicing
- SERVICING AND SUPPORT
- PAIRING THE REMOTE CONTROL TO THE APPLIANCE
- ACCESSING THE FUEL BED
- GLASS EMBERS
- FUEL EFFECT – CRYSTAL ICE GLASS EFFECT
- REMOVING THE FUEL BED
- REMOVING THE EFFECT SPINDLE -FUEL BED
- REPLACING THE FUEL BED LEDs
- REMOVING THE INNER SCREEN
- REMOVING THE FLAME EFFECT
- REMOVING THE EFFECT SPINDLE -FLAME EFFECT
- REPLACING THE FLAME EFFECT LEDS
- REMOVING THE FLAME EFFECT MOTOR
- REMOVING THE RECEIVER
- REPLACING THE HEATER
- REPLACING THE CONTROL UNIT
- PCB
- POWER SWITCH
- BUTTON BOARD
- SPARE PARTS LIST
- WIRING DIAGRAM
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Liberty 85
LED Electric Fire Range
with Thermostatic Remote Control
Instructions for Servicing
For use in
BLACK | BLACK |
---|---|
610-107 | 610-107 |
CONSUMER SUPPORT VIDEO:
www.gazco.tv/support/Liberty85
SERVICING AND SUPPORT
Servicing and Support
To keep your appliance looking and performing at its best, it must be serviced
annually. This service must be undertaken by a suitably qualified individual
and your retailer can organize this for you. Alternatively, Gazco offer a
manufacturers premium service with our friendly team of qualified engineers
which can be booked at www.gazco.com/support
PAIRING THE REMOTE CONTROL TO THE APPLIANCE
Signal Code
The below operations should be carried out before coding when changing to a
new remote or the unit cannot be controlled by the remote:
The reset button is located on the control panel located on the right-hand
side of the viewing window.
Press the reset button for 3 seconds (a pen point may be needed) until 3 short
beeps sound from the unit, release the button.
Within 10 seconds, press the button on the remote. The coding is finished when
1 long beep sounds from the unit.
Resetting the remote control is necessary if the appliance operates wrongly
due to an external interference signal and the remote control is not in use.
Open the back cover of the Remote.
Press the Reset button for 3 seconds and reset the coding.
ACCESSING THE FUEL BED
WARNING! The frame is earthed to the appliance
GLASS EMBERS
Spread the Glass Embers evenly over the fuel bed.
Note: The Ember Logs (See Log Layout) will rest directly on the fuel bed.
LOG SET – LOG LAYOUT
FUEL EFFECT – CRYSTAL ICE GLASS EFFECT
REMOVING THE FUEL BED
REMOVING THE EFFECT SPINDLE -FUEL BED
REPLACING THE FUEL BED LEDs
REMOVING THE INNER SCREEN
REMOVING THE FLAME EFFECT
REMOVING THE EFFECT SPINDLE -FLAME EFFECT
REPLACING THE FLAME EFFECT LEDS
REMOVING THE FLAME EFFECT MOTOR
REMOVING THE RECEIVER
REPLACING THE HEATER
REPLACING THE CONTROL UNIT
- PCB
- POWER SWITCH
- BUTTON BOARD
PCB
POWER SWITCH
BUTTON BOARD
SPARE PARTS LIST
No | Part Code | Quantity |
---|---|---|
1 | EL0900 | 1 |
2 | EL0715 | 2 |
3 | EL0713 | 2 |
4 | EL0711 | 1 |
5 | EL0727 | 4 |
6 | EL0792 | 1 |
7 | EL0706 | 1 |
No | Part Code | Quantity |
---|---|---|
8 | CE1891 | 1 |
9 | EL0718 | 1 |
10 | EL0700 | 1 |
11 | EL0678 | 1 |
12a | CE2017 | 1 |
12b | CE2025 | 1 |
12c | CE2033 | 1 |
WIRING DIAGRAM
COLOUR CODES
RD | RED |
---|---|
BU | BLUE |
YE | YELLOW |
WH | WHITE |
BK | BLACK |
BN | BROWN |
GAYE | GREEN & YELLOW |
NO.|
---|---
1| Top Light LED Board
2| Heater Unit
3| Fan Motor
4| Heater
5| Thermostat
6| Flame Effect Motor
7| Fuel Effect Motor
8| Button Board
9| Receiver Board
10| PCB
11| Flame Effect LED Board
12| Fuel Effect LED Board
13| Plug Connector Incoming
AC Supply:
230V 50Hz required
14| UK BS1363 Plug
13A BS1362 Fuse
FOR ENQUIRIES IN THE U.K (EXCLUDING NI):
Gazco Ltd, Osprey Road, Sowton Industrial Estate, Exeter, Devon, England EX2
7JG
Tel: (01392) 261900 E-mail: info@gazco.com
FOR ENQUIRIES IN EUROPE (INCLUDING NI):
Stovax Heating Group (NI) Ltd (Comp reg NI675194), 40 Linenhall Street,
Belfast, BT2
8BA DX 400 NR Belfast Tel: +44 (0)1392 261990 E-mail: northernireland@gazco.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>