Pestill PSELECRTZPA Electronic Rat Zapper User Guide

Pestill PSELECRTZPA Electronic Rat Zapper User Guide

SAFETY & WARNINGS

IMPORTANT!

• Always turn off power before handing this product.
• Ensure any leaves, debris, rodent droppings or urine are removed from the metal plates before use.
• Only the base (part with metal plates) of the product is waterproof. Do not expose the top cover to water or other liquids.
• If necessary, the metal plates can be cleaned using water. Ensure the product is thoroughly dried before reassembling and switching the unit on.
• Place the trap in a well-ventilated location, away from water and other liquids.
• During operation, if the trap is exposed to water is may cause a short-circuit resulting in incorrect operation.
• If the product is not being used for an extended period. Disconnect it from the power outlet or remove the battery

WARNING!

• Never place your hands or any objects into the device unless the power is turned off.
• This product emits a high voltage shock. Do not allow children or pets to play with, have access to or be in close proximity to this product. If a small or newborn pet enters this product, it may be fatal.
• Individuals with heart conditions or similar ailments should not operate and stay away from this device.
• Please use the device indoors or in a non-humid environment and avoid using the device in a flammable and explosive environment.
• This product can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved. Children shall not play with the product. Cleaning and user maintenance shall not be made by children without supervision.

OVERVIEW

1. Bait Cup : Place food inside to lure rodents.

2. Metal Plates : Delivers high-voltage shock to rodents.

3. Entrance : Allows rodents to enter the trap.

4. Battery Compartment : Requires x4 “D” batteries (not included).

5. Indicator Flashing GREEN : Rodent has been exterminated.
   Flashing RED & GREEN: Low battery.

6. AC Input : Use AC adaptor to connect the trap to a power outlet (optional).

7. Extension Port : Output for the remote LED.

8. Power Switch : Turns product on and off.

OPERATION

Connecting to Power

This product can be connected to a power outlet using the included AC.
If a suitable power outlet is not available, the trap can be powered using x4 “D” batteries.

• Remove the battery compartment cover.
• Insert x4 “D” batteries into the battery compartment (pay close attention to the orientation of the polarity symbols).
  Note : When the batteries are low and need to be replaced, the indicator will flash RED and GREEN.

Remote LED

• Connect the remote LED cord to the extension port on the trap.
• Mount the LED in a visible location.
• The LED will flash BLUE when a rodent has been exterminated.

Removing the Top Cover

• Hold the trap with both hands, slide the top cover away from the entrance until you hear a ‘Click’ sound.
• Remove the top cover by lifting it in an upwards direction.

Replacing the Top Cover

• Lower the top cover onto the base lining up the tabs with the four holes.
• Slide the top cover towards the entrance until you hear a ‘Click’ sound.

Baiting the Trap

Place a small piece of food onto the bait cup to use a lure for rodents. Food such as nuts, breadcrumbs, peanut butter and dry cat food will provide better results.

Using the Trap

• Place the power switch in the ‘On’ position. The switch indicator will flash GREEN and RED once.
• Every 10 seconds the indicator will flash RED, signalling that the trap is set.
• When a rodent enters the device, the indicator will turn solid RED, and the trap will emit a high-voltage shock (5000V-7000V).
• Once the rodent has been exterminated, the indicator will turn from solid RED to flashing GREEN.

WARNING : Do not touch or handle unless the indicator is flashing GREEN or the device is turned off.

• To dispose of the rodent, first ensure the trap is turn off then remove the top cover and tip the rodent into a garbage bin.

False Triggering

In some cases, the trap will indicate that it has exterminated a rodent but upon checking there will be nothing inside. This is completely normal and is caused by rodents triggering the alarm then escaping. If this occurs, the trap will need to be turned off and the bait replaced, if necessary.

SPECIFICATIONS

Power supply  :      x4 “D” batteries (not included) or 6V 1A power adaptor
Working voltage :  Up to 5000-7000V
Working current : ≤500mA
Standby current : ≤0.5mA

NOTES

Need more information?

We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>