JLABS KI2A56FJSD Jbuds Air Executive True Wireless Earbuds User Manual
- June 6, 2024
- JLABS
Table of Contents
JLABS KI2A56FJSD Jbuds Air Executive True Wireless Earbuds
We love that you are rocking JLab!
We take pride in our products and fully stand behind them.
YOUR WARRANTY
All warranty claims are subject to JLab authorization and at our sole
discretion. Retain your proof of purchase to ensure warranty coverage.
CONTACT US
Reach out to us at [email protected]
or visit jlab.com/contact 
REGISTER TODAY
jlab.com/register
Product updates | How-to tips FAQs & more
FIRST TIME SETUP
AUTO-CONNECTING EARBUDS
A. Take earbuds out of the charging case and remove stickers.
B. Press and hold both touch sensors 3+ seconds to turn ON. One earbud turns
solid white and the other earbud blinks blue/white indicating ready to pair to
your device.
CONNECTING TO BLUETOOTH
Select “JLab JBuds Air Executive” in your device settings. Voice prompt
“Bluetooth connected” followed by solid white lights will indicate you are
connected.
ADDING NEW / ADDITIONAL BLUETOOTH DEVICES:
Turn OFF Bluetooth from any previously connected device. Turn ON Bluetooth
from new device. Take earbuds out of the case. Earbuds will automatically
enter Bluetooth Pairing. Select “JLab JBuds Air Executive” in device settings
to connect.
BUTTON FUNCTIONS
- VOLUME DOWN : Single tap
- SIRI (iOS) or “OK GOOGLE” (ANDROID ): Double tap
- SWITCH MUSIC / MOVIE MODE : Press & hold 1+ sec
- EQ CHANGE: Triple tap (Cycles through 3 EQ settings)
- POWER ON: Press & hold 3+ sec
- VOLUME UP : Single tap
- PLAY / PAUSE: Double tap
- TRACK FORWARD : Press & hold 1+ sec ANSWER: Single tap
- HANGUP : Double tap
- REJECT INCOMING CALLS: Press & hold 1+ sec
- BE AWARE ON / OFF : Triple tap
- POWER ON: Press & hold 3+ sec
VOICE PROMPTS
- “Hello” : Power ON
- “Ready to Pair” : JBuds Air Exec are ready to pair to Bluetooth device
- “Bluetooth Connected” : Earbud is connected to device
- “Battery Full”: 100-80%
- “Battery Medium” : 80-20%
- “Low Battery”: Less than 20%When power decreases to 10%,
- “Low Battery” will play
- “Goodbye”: Power OFF
TURN OFF EARBUDS WITHOUT CHARGING CASE:
Enter your Bluetooth device settings and disconnect the JBuds Air Executive.
Earbuds will power OFF after 3 minutes.
EQUALIZER MODES
Triple tap left earbud for different EQ settings. Voice prompts will indicate
EQ settings (JBuds Air Exec will cycle 3 EQ settings)
JLab SIGNATURE JLab C3™ signature sound with amplified bass and vocals
BALANCED Even sound with no additional enhancements
BASS BOOST Amplified bass and sub-bass
CHARGING EARBUDS
Placing the earbuds in the charging case will power OFF earbuds and start
charging. Blue lights indicate earbuds are charging and will turn off when
fully charged.
When earbuds are taken out of the case, they will auto power ON and reconnect to your device.
CHARGING CASE
Connect the JBuds Air Executive to computer or USB 5V 1A (or less) output
device.
FITTING
Try the optional Cush Fins and all ear tips for best fit and proper seal.
Place the earbud in the ear canal and slightly rotate to adjust for best fit.
TROUBLESHOOTING
NO AUDIO IN LEFT EARBUD OR EARBUDS DISCONNECT FROM EACH OTHER (MANUAL RESET)
- Enter your Bluetooth device settings and forget the JBuds Air Executive. Fig
- Open the charging case door and leave both earbuds inside. Starting with ONE earbud, quickly tap the touch sensor 7x times. Light will blink blue 3x times. Leave the earbuds in the charging case. Fig C1
- Repeat with the other earbud. Quickly tap the touch sensor 7x times. 3 Light will blink blue 3x times. Fig
- Take both earbuds out of the charging case and keep them within 2 inches from each other. Wait for one earbud to turn solid white and the other to blink blue/white. You are now ready to pair to your Bluetooth device.
BLUETOOTH DEVICE DOES NOT CONNECT/RECONNECT
- Enter your Bluetooth device settings and forget the JBuds Air Executive. Fig
- Turn OFF then ON Bluetooth. Fig
- Take the earbuds out of the case. Wait for one to turn solid white and the other to blink blue/white.
- Select “JLab JBuds Air Executive” in device settings to reconnect.
- Instructional videos at: JLAB.COM/MANUALS
QUICK TIPS
- Fully dry off the earbuds before putting in the charging case.
- The left or right earbud can be used independently for music and phone calls. Simply choose one and take out of the case to connect.
- Choosing the correct ear tip makes a significant improvement in audio quality due to the proper seal for the driver. Test all ear tips for best results.
- Only ONE Bluetooth device can be connected at a time. Turn off Bluetooth on unwanted devices and turn on Bluetooth on chosen device to connect.
WARNING
Fully dry off the earbuds before placing in the charging case.
If the earbuds are damp or wet, this will cause damage to the charging case.
The warranty will be voided if the charging case shows damage by water/sweat.
CAUTIONS
- Avoid extreme heat, cold, and humidity.
- Avoid dropping or crushing the earbuds.
- Wax may build up in the earbud tips, lowering the sound quality. Carefully remove the wax with a cotton swab or other small tool to improve the sound quality.
- If you experience discomfort or pain, try lowering the volume or discontinuing use temporarily.
- If you experience regular discomfort while using this product, discontinue use and consult your physician.
- We recommend you treat your earbuds as you would a nice pair of sunglasses and keep them in safe location when not in use.
