Bullard XS Thermal Imager Charger Instruction Manual

: June 6, 2024
: Bullard

Table of Contents

OVERVIEW
- USING THE XS CHARGER ON A TABLETOP
- INSTALLING THE XS CHARGER IN A VEHICLE:
MARKING AND DRILLING THE PANEL
- MARKING AND DRILLING THE PANEL
- MOUNTING THE XS CHARGER
OPERATION
- CHARGING CONFIGURATIONS
INSERTING THE TXS INTO THE XS CHARGER
TROUBLESHOOTING
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Bullard XS Thermal Imager Charger

OVERVIEW

USING THE XS CHARGER ON A TABLETOP

The XS Truckmount Charger can be used as a stand-alone device on a tabletop. To use in this manner, install the optional AC adapter as pictured in Figure

INSTALLING THE XS CHARGER IN A VEHICLE:

Installation

The XS Charger is designed to be mounted on any convenient flat-panel surface in a vehicle. When installed and used in accordance with these instructions, the unit is designed to comply with NFPA 1901-14.1.11.2 and EN1846-2 (see caution for proper installation).
Location Select a conveniently located, flat-panel surface of sufficient size to accommodate the unit. The unit can be mounted in any orientation and will comply with NFPA 1901-14.1.11.2 and EN1846-2. The XS Charger attaches through with five (5) #10 Hex Head Drilling Screws that are also provided with the unit . Allow 6-inch clearance above the charger to remove TXS.

NOTE The adapter plug included with your XS Charger may differ than the plug in Figure 1, according to your region.

NOTE The XS Charger should be connected to an un-switched fused circuit such as the apparatus battery that continues to provide power when the vehicle is not in use. Wiring the XS Charger to a switched circuit or through a relay may result in discharged imager batteries if the vehicle is left idle for periods of more than a few days at a time.

Item	Requirements
Polarity	Red: Positive +

Black: Negative –
Input voltage| 12V – 24V
Input current
Minimum gauge| 2A @ 12V
18 AWG / ø 1 mm²

DO NOT wire the XS Charger to a third-party apparatus battery charger! Failure to comply may result in improper function of the XS Charger.

MARKING AND DRILLING THE PANEL

Print template (located on the back page of this manual) and place the template in the desired position in the truck. Mark the locations of the five countersunk holes and electrical wire hole using the template as a guide. Drill a suitably- sized hole in the truck panel through which the XS Charger wiring will pass, ensuring that there are no sharp edges or burrs that could harm the wiring insulation (Figure 3).

MOUNTING THE XS CHARGER

First, make sure that the power is disconnected from the supply wiring. Next, connect the positive power source wire securely to the Figure 4 red conductor located on the back of the XS Truckmount Charger. Then connect the negative power source wire securely to the black conductor located on the back of the XS Truckmount Charger.
The XS Truckmount Charger screws directly into the flat panel using the five (5) #10 Hex Head Drilling Screws included in your installation kit. Installation is now complete (Figure 4).

Bullard-XS-Thermal-Imager-Charger-Installation

OPERATION

The XS Charger charging station is designed to perform the following functions: ·Securing the imager in the vehicle in accordance with
NFPA 1901-14.1.11.2 and EN1846-2.

Storing and recharging the battery in the imager and maintaining the battery at full charge.
Securing a spare rechargeable battery in accordance with NFPA 1901- 14.1.11.2 and EN1846-2.
Storing and recharging the spare battery and maintaining it at full charge.

CHARGING CONFIGURATIONS

The XS Charger allows for a flexible camera management and can charge simultaneously:

two imagers
two batteries
one imager and one battery

INSERTING THE TXS INTO THE XS CHARGER

NOTE
To store the TXS in the XS Charger, a battery must be installed in the camera. Without a battery installed, the rubber strap will not secure the camera properly. Therefore, storing a camera without the battery installed can result in non-compliance with NFPA 1901-14.1.11.2. Set the imager firmly into place in the XS Charger. Maintain the unit in position, fold over the rubber strap and attach in place so that the rubber ball fits into the hook.

REMOVING THE TXS FROM THE XS CHARGER

Pull down on the rubber strap until the rubber ball comes loose from the hook, unfold the rubber strap and remove the camera from the charger.

REPLACING THE RUBBER STRAPS

The rubber straps are designed to be replaced. To replace the rubber straps, unscrew with a Phillips or flathead screwdriver, pull out the hex head screw and binding barrel, replace the strap, and reassemble. (figure 6)

INSERTING THE SPARE RECHARGEABLE BATTERY INTO THE XS CHARGER

The XS Charger charger is designed so that a spare battery, or second camera can be recharged on the same unit. Set the battery firmly into place in the XS Charger. Maintain the battery in position, fold over the rubber strap and attach in place so that the rubber ball fits into the hook.

CHARGING STATUS

The charger is automatically activated when an imager or battery is inserted. Battery charge condition is indicated by the color of the light emitted by the LEDs.
PULSING GREEN: Battery is charging
SOLID GREEN: Battery is fully charged
FLASHING ORANGE: Error condition (problem with the TI or charging system).

EXPLOSION HAZARD. Do not connect or disconnect the equipment to any charger in an hazardous location.
Do not short circuit, crush, incinerate, or disassemble.
Risk of fire, explosion, or burns.

Only Charge using Bullard XS charger, or Bullard provided USB plug.

Always use the correct charger and refer to the manufactuer’s instructions for proper charging instructions. Retain the original product literature for future reference.

Battery Pack must be recycled or disposed of properly.

Battery Pack charging temperature 0˚C – 45˚C.

TROUBLESHOOTING

If you experience any problems with your TXS we refer to our website (www.bullard.com/txs) for the latest information on fixes, updates, and best practices.

The XS Charger is compliant with NFPA 1901-14.1.11.2 and EN1846-2 and is able to be mounted in any orientation. Please use caution when choosing a mounting location so that, if the camera is accidentally dropped while being installed in the XS Charger, it will not injure anyone nearby. For this reason, we do not recommend mounting the XS Truckmount Charger on the ceiling of any vehicle. Use only a fused power source of 2 amp capacity and 12-24 VDC voltage. Ensure that the polarity of the power supply wiring is correct. Failure to follow these instructions could result in serious injury or malfunction of the unit.

California Proposition 65

Cancer and Reproductive Harm- www.P65Warnings.ca.gov.